Search Documents

By I E. "Chip" Harris, G Alan Foster

Whilst a great deal of published data exists as to safe ground vibration and air blast levels which result from blasting little documented research has been carried out to determine how and why human beings complain about blasting operations. This paper gives the authors thoughts and experiences of why complaints arise and practical steps to minimize such complaints.

Jan 1, 1977

It is a case study of huge rock-mass, loosened out from the parent rock-body, & posing a potential danger to structures down below the slope on which this rock mass was standing. Case was dealt in two phases, by tying/stitching the rock mass to the parent rockbody and breaking it using controlled blasting technique.

Jan 1, 1997

By Terry Graf, Bill Thompson, John Guenther

SYNCRUDE CANADA LTD.. operates the largest synthetic crude oil production facility in the world. Over 60,000,000 Bank Cubic Metres of oil sand is mined each year from their open pit located in Fort McMurray, Alberta. Despite the extremely cold temperatures encountered during the winter months and the problems associated with frost buildup, SYNCRUDE has continued to operate on a 12 month per year basis. In 1989 SYNCRUDE mine management embarked on a comprehensive Frost Blasting program to improve mine production of their oil sand moving equipment. The following paper will discuss the development of their frost blasting program to its current status.

Jan 1, 1993

By P D. Kasbanis, Lyall Workman

The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of "available energy" associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

Jan 1, 1996

By Gregory S. Parker

The explosives community has seen tremendous technological advances during the past several decades. When this industry was in it's infancy and even past, Powder Monkey's defied the odds by relying on daring and cunning to unleash the power contained in nitroglycerin and black powder. Unlike the manufactured improvements, there has been little in professional evolution amongst the blasting fraternity unless provoked (for the most part) by the government. It is the intent of this author to advance the cause of an industry wide training and certification program, uniform in nature and broad-based enough to be voluntary, giving states whose outstanding programs are already in place, the opportunity to provide input. In creating this type of atmosphere, grandfathering, reciprocity and accessibility would be paramount. With ISEE taking a firm leadership role during the inception and NICET's involvement in the administration, the idea postulated here is intended to spark interest and debate, bringing the inception of such a program to the forefront.

Jan 1, 1995

By Yoshihiro Moriyama, Toshihiro Okitsu, Ryouichi Banno

The fracturing composition using the gas pressure generated by the thermit decomposition reaction gives the following performances.

Jan 1, 1995

By Thomas L. Linton

The results of an extensive literature review and field experiments regarding the effects detonation of high energy explosive have upon various aquatic organisms are reported. These results were used to modify regulatory permitting criteria in Texas. Three separate field experiments were conducted. In the first study, surface placed charges were used in a marine habitat. In the other two, the charges were placed in drilled holes. In one, which was in a freshwater environment, the drilled holes were filled with drilling mud after placement of the charges. In the second, which was in an estuarine environment the holes were allowed to sit for thirty days prior to detonation to permit natural back-filling to occur by water transported sediments. A variety of aquatic organisms held in wire cages were exposed to detonations. Immediate and long-term effects of the exposure were determined based on external and internal visual observations. Damage to aquatic organisms was found to be reduced by placing the explosives in drilled holes and back-filling the holes prior to detonation of the explosives.

Jan 1, 1997

By Alan Hooper

This paper and slide presentation is a brief rundown on what is probably the worst natural devastation I have ever witnessed. The epicenter of the quake that so violently shook Mexico City occurred 230 miles away near Mexico's west coast. The first calculation placed the quake at 7.8 on the Richter scale. This was later upgraded to 8.1. Each unit increase on the Richter scale indicates about a 30 fold increase in energy released. The quake was felt in much of Mexico and south Texas and damage occurred in many other Mexican cities. On the morning of September 19, 1985, at 7:18 A.M., the ground went into motion and shook for approximately 2 to 4 minutes. During this period most of the devastation occurred. At 7:38 P.M. the following day, the second quake hit and more buildings fell from this 7.5 quake. The ground in Mexico City moves like jello since it is a dry lake bed 7,350 feet above sea level.\

Jan 1, 1986

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

In March of 2001 Barrick Goldstrike Mines, Inc. began evaluating the potential benefits of electronic detonators at the Betze Post open pit gold mine. The original evaluation focused on increased fragmentation, and excavator productivity. During the original evaluation there was an attempt to quantify mill throughput. Early tests indicated that there would be a benefit to mill throughput, however management was hesitant to take on the added cost of electronic detonators based on the initial evaluation. In early 2002 a decrease in mill throughput was being forecast as a result of harder ore being encountered. As a result of the initial electronic detonator evaluation a team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative. This initiative was targeted at improving mill throughput as the harder ores were encountered. Batch tests were conducted to determine if adjustments to drilling and blasting in the open pit could increase mill throughput and justify a 50% increase in drilling and blasting costs for the harder ore material.

Jan 1, 2004

By TA Louw, Dr CM Lownds

In an era where profits are constantly being eroded, mines are looking towards technology developments to assist them in solving mining problems and reducing mining costs. An emerging technology that could assist mines in becoming more cost effective is electronic detonators. Electronic detonators have been under development for several years. Over the past three years, the spotlight has fallen on commercial use of electronic detonators and the extent to which the promise of precise and programmable timing can assist mines with their environmental and productivity problems. This paper uses case studies to demonstrate both surface and underground applications where electronic detonators and blasting systems were used to solve typical mining problems such as vibration and fragmentation. Safety aspects such as hanging wall conditions and high wall stability also benefited from the use of electronic detonators. The paper also demonstrates how the use of accurate electronic detonators and blasting systems has resulted in improved/more even fragmentation with further downstream efficiencies. These efficiencies may include increased cast percentages, reduced oversized rocks, quicker cleaning times and increased production rates.

Jan 1, 2004

By Francis O. Otuonye

The results of an ongoing study to determine the response of full contact rock bolts to shock waves due to blasting are presented. A time domain systems modeling and analysis technique was used to identify the axial and bending response of the bolt when explosives charges are detonated at close-in distances.

Jan 1, 1993

By Dale S. Preece, Lee M. Taylor

Computer simulation of the physics involved in conventional rock blasting can be split into two phases; transient stress wave propagation and rock motion. Because the two phases involve totally different mechanisms and time scales, they must be numerically modeled with two different computer programs. The first phase is usually modeled with a finite element or finite difference code which treats the rock as a continuum and simulates the transient stress wave and subsequent fragmentation of the rock. The second phase is usually modeled with a distinct element technique where the rock mass after fragmentation is no longer treated as a continuum but as a finite number of distinct particles that interact with each other through collision mechanics.

Jan 1, 1989

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

By Vincent Thorne

On January 2, 1992, the R. Zoppo Company of Stoughton, Massachusetts started drilling and blasting operations on U.S. Army Corps of Engineers Project Number: DACW33-91-B-0072 to widen and deepen the Portsmouth Harbor and Piscataqua River Navigation Channel.

Jan 1, 1993

By Ron Fish, Cherokee Stone

Drilling and blasting in open pits is very unique in Southern Florida. Crushed limestone, the state's most abundant mineral resource, is retrieved from the bottoms of huge open pits that are completely inundated with fresh water. It is this industry that makes southern Florida the fastest growing area in the United States.

Jan 1, 1986

By Gungor Tuncer, Ali Kahriman

"In bench blast design, not only the technical and economical aspects, such as block size, uniformityand cost, but also the elimination of environmental problems resulting from ground vibration and airblast should be taken into consideration."

Jan 1, 1999

By P N. Blakey

The base metal orebody of Texasgulf Canada Ltd. was mined initially by open pit. Conventional mining techniques were followed underground, but experimentation showed that open pit methods of drilling and blasting could be adapted. This paper deals with the consequent development of blasting techniques to suit underground stope design and damage criteria, in a large tonnage operation.

Jan 1, 1978

By G F. Baur

Even though the benefits of an effective, perimeter control program in production and development blasting are evident to most everyone involved in the mining industry, there continuer to be only select properties where such a program is in effect and is producing on-going and measurable results.

Jan 1, 1992

By AN Gupta, N V. Srinivasa Rao

Initiating devices like detonators use sensitive primary explosives. Successful detonation of secondary explosive is achieved by suitable source of energy from primaries. The most widely used primaries contain toxic lead azide and lead styphnate, dinitrodiphenol or tetracine. All these primaries are very sensitive to friction, impact and heat. The handling of these chemicals is very hazardous and many accidents reported in detonator manufacturing were from these primaries only. In addition to this high sensitivity, lead azide and lead styphnate contain lead which is toxic.

Jan 1, 2014

By Ralph King

Blasting has been completed when the lawyer calls to say that a landowner has filed a suit alleging damages to the roof of his home. Mitigation talks fail to produce an adequate resolution and the case goes to court. The blaster has pictures of the area made after the blasting was done showing the good condition of the roof. However the judge fails to allow the photographs to be entered as evidence and the homeowner wins the case.

Jan 1, 2008