Search Documents

By Chulgi Suk, Hoon Park, Hyonsoo Kim, Hakman Kim, Sangho Cho

Dust emission from blast demolition and other construction activities can be a nuisance; it is widely recognized that fine particles less than 10 µm in equivalent diameter (called PM10) may cause health problems. Mist spray systems, such as rain guns, sprinklers, water/surfactant sprays (or foams) etc., are some of the most effective dust suppression methods. A large amount of research has showed that when water droplets are produced in an equal amount to that of dust particles, the airborne dust is suppressed by the agglomeration of dust and mist particles. A method for generating micro-sized mist from water, achieved by the detonation of explosives in the water tube, was suggested and is called the ‘detonationdriven water bag burst system’. There are many experimentally observed limitations of the explosioninduced water break-up process. The water bag explosion tests were simulated using the AUTODYN software, in order to investigate the aerosolization mechanisms of the detonation-driven water and water break-up process into micron-sized droplets. As a result of the numerical analyses, the diffusion direction of water when detonating in the central interior part of water tube was radioactive and significantly stronger than when detonating in the bottom exterior part; this is due to the compressive flow of the volume change inside of the water tube, which resulted from the blasting wave inside of the tube, as well as the reflected pressure on the ground. Blast tests of full-scaled reinforced concrete columns were conducted to verify the effectiveness of the suggested detonation-driven water bag burst system. The water breakdown and dispersion that occurred while blasting the reinforced concrete columns were observed using a high-speed camera, and dust generation was monitored using four density detectors. The suggested detonation-driven water bag burst system showed that the average dust density decreased by up to 7 mg/m3.

Jan 1, 2016

By Nikolaos Petropoulos, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature. In this study, pure emulsion was tested in confined conditions to better simulate the behavior of the detonation of the explosive in rock mass conditions. A methodology is proposed for carrying out the evaluation of the explosive performance. The blasthole diameter of the samples varied from Ø 25 mm (0.98 in) up to Ø 65 mm (2.55 in). The confiner was a magnetic mortar cylindrical sample with mechanical properties similar to a rock mass. A streak camera and VoD probes were used to measure detonation front curvature and VoD. The data was analyzed and correlated with the physical parameters of the explosive. Additional to this, the data was further used to calibrate numerical models in LS-Dyna.

By Gordon M. Matheson, Douglas A. Anderson, David K. Miller

"Traditionally, analysis of vibrations from blasting has been focused on peak particle velocity fordetermining the likelihood of both annoyance and damage. The US Bureau of Mines, in RI 8507,indicated the importance of frequency in vibration. Methods of controlling the vibration by reducingthe vibration concentrated in certain frequency bands using delays have been successful over the past decade."

Jan 1, 1997

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By Douglas A. Bartley, Davey Bickford, Raphael Trousselle

The long awaited arrival of a high accuracy detonator to reach the explosives end user will provide new opportunities the blasting community to become better equipped and able to improve upon the current approaches and methodologies used in blast design as they apply to the mitigation of adverse effects from blasting. This paper will detail the approach and findings throughout a several month research project to quantify the high accuracy detonator benefits and to mitigate a long standing vibration problem at a hard rock stone quarry in the state of New York. The tests conducted in this study were designed to provide important information as to the relationship between the use of high accuracy detonators and overall blast performance in terms of ground vibration prediction, control and improved rock fragmentation.

Jan 1, 1998

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Kagan Ozdemir, Adiguzel Deniz

This paper presents the results of ground vibration measurements induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel which has been driven at a depth of approximately 20-40 m deep under a highly urbanized region of Istanbul city in Turkey. This tunnel is being constructed by a joint venture group. The formation encountered during the construction is classified as hard and strong rock by laboratory and field tests performed by the joint venture group. Within the scope of the study, for the prediction of the peak particle velocity and to determine the slope of the attenuation curves together with the maximum charge per delay for the S4 shaft tunnels and S12 shaft tunnels of this tunnel route, ground vibration components were measured carefully by using four vibration monitors (Instantel Minimate Plus model) during the advancement of the tunnels which required blasting. The particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms in order to predict, and compare the influence grades to the neighbouring buildings, and structures. Also, data pairs of scaled distance and peak particle velocity obtained from 114 records at S4 shaft tunnels and 79 records at S12 shaft tunnels were analysed statistically. Empirical relationships with correlation at the 95 % confidence interval were established for different rock units (diabase and arkose) and suggested for the test sites in order to estimate particle velocity of the ground vibrations.

Jan 1, 2007

By G. Adderley, A. Wetherelt

The problems of poor drilling in underground operations have been highlighted on many occasions. Incorrect collaring and poor angular deviation can all lead to an increased block size, dilution, over-break adding to both cost and time, while in a tunnelling operation sidewall damage and a poor percentage pull from a blasted round has similar consequences. This paper sets out to further investigate the ability of the laser scanner method of obtaining drill hole deviations and collaring errors at the face as described by Wetherelt and Williams (2006). Tests were carried out to compare measured inter-hole burdens from this method in comparison to that obtained using a total station survey. To investigate the ability of these methods to accurately determine drilling errors, a field test was carried out through an analysis of a series of pre-drilled blast holes of known inclination and direction. A time-motion study was also conducted for a varied number of holes to assess the usability of each method. In line with current research into blast vibration being undertaken at the Camborne School of Mines, 6 cut blasts were carried out to establish the effect of poor drilling on a blasts success to see whether an increased burden at the toe of a hole had an influence on vibration.

Jan 1, 2009

By Brian Lewis, Reinhold Daykin Schnell

Blasting is the primary and most effective method for breaking and moving material at most mine sites. The blast design is often adjusted in efforts to optimize the effectiveness of the blasts’ explosive energy while minimizing costs. When adjusting blast design parameters, it is important to adjust one parameter at a time, observing and analyzing the potential effects of the change on the overall blast performance.

Feb 6, 2023

By Dean Nichols, Matt Ortel

Explosive accidents in the United States have brought increased attention to emergency operation plans (EOP) at all facilities that manufacture, transport, or store hazardous materials – particularly explosive materials. Explosions are sudden, powerful, and complex events that are difficult to characterize in terms of the thermal, over pressure, and debris effects. Industry, regulatory, and public officials require emergency response planners to not only anticipate the blast effects of an explosion, but also to prepare an appropriate response.

Jan 1, 2016

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By Tamara Whitaker, James Gunderson, Ruilin Yang

This paper presents the results of a vibration control project conducted in soft overburden at a surface coal mine located in the western United States. The study uses near-field blast vibration monitoring, analysis and modeling techniques developed in house. Accelerometer-equipped seismographs were utilized for near-field vibration monitoring and analysis. Vibration control was achieved through field data regression as well as vibration modeling using the multiple seed near-field blast vibration model (Yang and Scovira, 2007). The regression was conducted between peak particle vibration parameters and the minimum scaled distance per delay. From the regression analysis, the curves of upper bounds for peak particle vibration parameters and charge weight were developed. The dominant frequencies of the blast vibration were also addressed in this project. The regression curves and near-field vibration model guided the blast design to control blast vibration for maximizing the recovery of coal and maintaining mine productivity.

Jan 1, 2008

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By Brian W. Stump, David P. Anderson, John Wiegand

Mining explosions are designed for a variety of purposes including the fragmentation and movement of materials. The blast design is dependent on the particular application intended and the material properties of the rock. The range of mining applications from hard rock quarrying to coal exposure to mineral recovery leads to a great variety of blasting practices.

Jan 1, 1997

By Charolett Hayes, A. L. Russell, Anthony J. Bednar, Jared Smith, Valentine A. Nzengung, Stephen L. Pilcher

The manufacture of Energetics Materials (EM), including maintenance and demilitarization of munitions causes dangerously high levels of explosives residues to be harbored in building features. The two commonly approved methods of decontaminating energetics contaminated equipment and building features are thermal treatment and steam washing. The current regulatory environment is generally becoming more stringent and unfavorable to thermal and steam decontamination because of their adverse impact on air, soil, and water and their ineffectiveness to completely remove accumulated energetics from foundation cracks, internal and external piping, voids in walls and ventilation systems, and internal cavities of fixed equipment. However, chemical destruction of energetics, especially high explosives, is gaining acceptance as a safer, cost-effective and environmental friendly alternative to thermal and steam decontamination. Organic explosives, including nitramines and nitrate esters are oxidized organic compounds that are susceptible to chemical oxidation and reduction reactions. Under suitable conditions, a chemical reagent consisting of sulfur-based bulk reductants (neutralent) commercialized as MuniRem generates highly reactive free radicals that very rapidly degrade many energetic compounds to innocuous end products while stabilizing metals as the insoluble metal sulfides.

Jan 1, 2016

By Türker Hüdaverdi, Özge Akyildiz

"In this research, image analysis technique, Kuz-Ram and KCO Models were used to examineefficiency of the quarry blasts. Investigations were performed in Cendere region, Istanbul. As a firststep, image analysis software was used to determine particle size distribution of muckpiles.Additionally, the results of KuzRam and KCO fragmentation models were compared to the results ofthe image analysis technique. The efficiency of KuzRam and KCO models was investigated and theimportant points to be considered were explained. Additionally, the effect of the rock factor valueson the size distribution curves was investigated. The blasthole diameter is 89 mm. (3.5 in) in thestudied quarry. Each measured blast has a different burden, spacing and stemming length. Blastholes was drilled in a staggered pattern. It is concluded that, KuzRam and KCO models can be successfully used to determine fragment size distribution in Cendere Region Quarries, Istanbul. Site engineers can predict blast fragmentation using the theoretical fragmentation models and they may change blast design parameters before blasting operation if necessary. It is possible to calibrate the Kuz-Ram and KCO fragmentation models using the measurements obtained by image analysis technique."

Jan 1, 2016

By Stephen H. Chung

The SABREX computer blast simulation program permits the study of the effective use of explosive energies and predicts the total performance of a blast in terms of:fragment size distribution: muckpile profile; breakage at grade, column and collar with respect to the control case; crack penetration; damage envelope behind and beneath blastholes; a complete cost analysis including explosives, drilling and accessory costs

Jan 1, 1995

By Francisca Tapia, Jorge Blázquez, Paulo Couceiro, Patricio Vergara, Luis Manriquez, Luis Martínez, Juan Navarro

Efficient energy transmission is critical for effective rock fragmentation in open-pit blasting. However, in zones with highly fractured or soft rock, mismatches in acoustic impedance between the explosive and the rock can lead to significant energy loss. These mismatches reduce fragmentation efficiency and, when energy input is increased to compensate, can trigger unintended side effects such as NOx fume generation. This paper presents a novel methodology that integrates the Fragment Size Energy Fan model with acoustic impedance theory to dynamically optimize explosive energy delivery. A redefined impedance formulation captures volumetric energy transfer and enables the calculation of a Rock Impedance Factor (RIF), calibrated through non-linear regression. To operationalize the model, rock impedance is estimated using the X-4Traits Model—a meta-learning algorithm that interprets Measurement While Drilling (MWD) data from both autonomous and manually operated drills to produce high-resolution, spatially distributed impedance maps. The methodology was calibrated and applied at Minera Escondida Limitada (MEL), using data from over 218,447 blastholes and 526 blasts. Two case studies illustrate its application: Expansion 1 demonstrates improved fragmentation consistency and a 10.7% reduction in powder factor by aligning explosive energy with local impedance variations; Expansion 2 highlights the model’s utility in managing NOx emissions in fractured zones by optimizing energy distribution and confinement without compromising fragmentation. This impedance-based framework provides a robust tool for improving fragmentation outcomes, optimizing energy use, and enhancing control in geologically variable blasting environments.

Jan 26, 2026

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016