Search Documents

By Julio Cesar Barbosa de Freitas, Rafael Gonçalves Araujo, Túlio Soares, Jair Koppe, Augusto Ferraz Ribeiro, Pedro Barreto Garcia

This study thesis was motivated by the fact that it is of fundamental importance for open pit mining that the slopes initially have a geometry in accordance with what is proposed in the mining planning. This occurs because an inconsistency in this design can impact the operational safety and economic solutions of the mining project. These consequences can be explained by the fact that rock blasting close to mining limits requires specific study due to the attention required. Because, when this operation is not carried out properly, the mining plan in the mine may not be respected and may create risks to the operation due to the presence of unstable blocks on the slopes (Mackenzie). In this sense, Mackenzie (2004) cites pre-split, trim blasting and buffer as commonly used explosive blasting techniques that aim to limit damage beyond the projected wall. Therefore, Enaex Brazil realized the need to better understand the pre-split method. To do this, it is necessary to understand how the energy released during detonation is perpetuated in the rock mass when this technique is used and when it is absent. Thus, this analysis is based on a seismic study that allows the creation of vibration attenuation laws and an elementary wave damage model, which allows the local characterization of the rock. With this model it is possible to relate the peak levels of vibration during blasting and the extent of damage, but a critical level of vibration (PPVc) and its relationship with the Uniaxial Comprehension Resistance (UCS) are also defined for the start of fracturing and its level (McKenzie et al, 1995). And, mainly, this work aims to address a way to measure the pre-split filter potential by comparing the attenuation law with and without pre-split, ultimately knowing whether this finishing blasting is being effective, to understand the pre-split filter capacity.

Jan 21, 2025

By Paul Worsey, Gillian Worsey

The explosives industry is about to reach a critical turning point in human resources. The average age of employees of the largest US explosives company is over 50 and an estimated 5,000 engineers are due to retire from the mining industry over the next decade, with less than 200 mining graduates per year nationally. Not just in the USA, this is a worldwide problem. In Canada the Mining Industry Human Resources Council (MIHRC), reported that older mining engineers are retiring early – at the age of 59.5 on average. It predicts that mining companies will need to hire 370 mining engineers by 2016 and 665 by 2021. The Minerals Council of Australia has predicted the need for an additional 86,000 mining professionals and skilled mine workers by 2020, and the Indian mining industry is also facing a shortage of between 2,500 to 3,000 engineers per year.

Jan 1, 2014

By Michael Wieland

Work-principle computations for explosions underwater or in rock reveal the way the thermodynamic characteristics of surrounding material influence the resulting shock and heave. To reach total thermodynamic equilibrium under such transitory dynamic circumstances, reactions must quickly readjust to changing circumstances, which works for molecular (military) explosives where the fuel and oxidizer type atoms are originally in close proximity. For non-molecular mixtures with their dispersed zones of oxidizer or fuel, in particle or droplet form, there are numerous unproductive collisions, increasing the wait time required to reach chemical equilibrium. Underwater test data for molecular explosives compare rather well with the shock and heave resolved from the work-principal model, while the non-molecular explosives normally used in mining tend to yield a noticeable discrepancy. Years ago, it was recognized that the underwater shock was lower than expected and the heave was higher than expected for ammonium nitrate fuel oil (ANFO), though their resultant sum for the total work was roughly what was expected. When the readjustment of thermodynamic equilibrium warrants quicker chemistry than occurs in underwater or rock shooting, the time-retarded chemistry reduces the shock and raises the heave within the surrounding material without reducing the total work, unless the reaction retardation is quite severe. This technical complication in reality is a nonequilibrium issue that is difficult to resolve with just thermodynamics, though a rational set of transformation factors is formulated herein to represent those circumstances.

Jan 1, 2008

By John Wright

As part of the redevelopment of the Royal Brisbane Hospital complex in Australia, a number of antiquated buildings were to be demolished and replaced by newer, modem facilities. Aside from the decommissioning of the hospital buildings, the project called for the removal of approximateIy 24,000 bank cubic metres (bcm) of varying quality rock material. Given the sensitivity of the project, in particular the close proximity of the required excavation to the existing hospital structures (-3 metres at the closest point), and the requirement that these were to remain lily operational during the construction phase, it was initially proposed to use hydraulic rock hammers as the primary means of excavation. Poor production rates and unexpected dif3icuIt rock conditions led to a revision of the excavation methods and a feasibility study on drill and blast practices was undertaken. Subsequent to an initial series of trial blasts to illustrate that vibration and flyrock could be adequately controlled, drill and blast methods were used in conjunction with mechanical methods of rock breakage. This paper reviews the drU and blast processes and the practices which were necessary to comply with the multiple constraints imposed on the project. The project has highlighted that modified drill and blast practices remain a cost-effective method of excavation, even in sensitive areas which are commonly deemed inappropriate for such methods.

Jan 1, 2000

By Steven Townend, Don Wadden

In today's global economy the need to stay competitive is essential for commercial survival and growth. To this end Inco is committed to continuous improvement in its operations. Various aspects of the mining process have been examined to find ways of improvement.

Jan 1, 1994

By Peter Moser, Andreas Grasedieck

In modern rock blasting it is becoming more and more important to achieve a certain specified fragmentation. This means that the rock particles formed as a result of the blast should conform to a desired particle size distribution. An important issue with respect to achieve a desired blast result in terms of fragmentation is both the availability of models for the prediction of the characteristic of the particle size distribution of blasted material and the determination of the energy necessary to achieve a certain fragmentation status. Within the research project “Less Fines” funded by the European Union under project reference G1RDCT200000438, the latter has been addressed by the Department of Mining Engineering& Mineral Economics of the University of Leoben. For that purpose fragmentation results from lab scale blast tests have been analyzed and the relationship between the specific charge used for the blasts and the resulting specific surface of the fragmented material has been examined. Linear relationships between the specific charge and the specific surface of the resulting fragmentation were found for various types of rocks to apply over a range of 10 for the powder factor.

Jan 1, 2004

By John Kemeny

There are many methods used to predict blast fragmentation, including empirical and numerical models, field trials, and experience from ongoing blasting. All of these methods require an accurate measurement or prediction of the rock mass properties. These properties include the characteristics of the rock fractures, including fracture density, friction angle, orientation, length, roughness, fill, etc. They also include the hardness of the intact rock, water content, and other parameters. This paper describes three new technologies that can be used to automatically or semi-automatically obtain rock mass properties: digital image processing, 3D laserscanners, and drill monitoring systems. Each of these technologies is described, including the current state of the art, current limitations, and their future potential. Each of these three technologies has advantages and disadvantages. These new technologies, however, have the potential for providing accurate rock mass information in an automated and real time fashion. This information can then form the basis for a new generation of real-time, database driven blast fragmentation models.

Jan 1, 2004

By J. D. Aubertin

Rock blasting is a complex engineering process that requires in-depth knowledge of operations and geomechanical conditions. Acknowledged design precepts are based on cratering behavior associated with stiff hard rock masses. Other cratering mechanisms may however arise under certain geomechanical conditions such as extremely fractured rock masses, or with soft rocks such as rock salt and potash. The burden dimension also plays an important role in the prevalent cratering mechanisms of a given blasting condition. The present article investigates the variability of cratering profiles and geometrical trends based on characteristic geomechanical differentiation and considering the influence of burden. The differences in observable mechanisms are examined through small and large-scale single hole blast (SHB) tests. SHB tests involve a series of individual shots blasted parallel or sub-parallel to an open face. The burden dimension is varied to obtain burden dependent characteristic trends. The breakout shape is represented by a crater model in the form of a power law equation capable of describing prismatic, concave and convex cratering. The formulation comprises two reference index parameters that can describe the geometrical and geomechanical conditions. SHB test campaigns conducted in rock salt, limestone, massive amphibolite, pinolite, and grout blocks are compiled in quantitative manner to demonstrate the influence of geomechanics on cratering profiles. The observed trends are corroborated through numerical modelling carried on Finite Element Model (FEM) LS Dyna to investigate the prevalence of specific cratering mechanisms. A series of SHB tests at large and small burden values are also used to showcase the influence of geometry on the prevalent cratering mechanism and the resulting crater

Jan 1, 2024

By W. L. Saunders, Richard T. Dana

The dynamites are graded according to the percentage of nitroglycerin that they contain. Thus a “40% powder” would be one in which the sticks, weighing one-half pound each, would include one-fifth of a pound of pure nitroglycerin. Dynamite is usually packed in paper cartridges weighing about one-half pound each which will vary in diameter. When ordering, it is customary to specify a size of cartridge that will as nearly as possible fill the drill hole, the commonest size being 1 ¼” in diameter by 8” in length. It is nearly always shipped in 50-lb. boxes, which have a volumetric capacity of 3/4 cu.ft.

Jan 1, 2013

By Jody Todd, Ernesto Villaescusa, Ronald Lachenicht, Kelly Fleetwood

In the underground environment, characterisation of a rock mass during the mining cycle becomes increasingly difficult due to a lack of rock mass exposure for measurement or observation. In most cases rock mass characterisation occurs prior to mining by inspection and logging of exploration drill core, or prior to mass excavation through drive mapping for geological and geotechnical data. Characterisation strategies, if applied during the mining cycle, can reveal near-field anisotropies that may affect the behaviour of the rock mass with respect to excavation. These methods can aid in understanding the performance of stopes based on geometry, in-stope extraction sequence, and stress modelling. One such method of characterisation involves the use of production blast vibration monitoring and analysis as indicators of rock mass anisotropy through travel-time tomography.

Jan 1, 2008

By David Harrison

The Charleroi Locks and Dam (Figure 1) was completed in 1932 and is located on the Monongahela River, approximately 22 miles (35 km) south of Pittsburgh, in Charleroi, Pennsylvania. It is comprised of a 420 foot (128 m) gated dam, and a 720 foot (219 m) by 56 foot (17 m) land side lock which provides for a 16.6 foot (5 m) vertical lift.

Jan 1, 2015

By Winfried Rosenstock

AEBT has been available for a couple of years and is successfully applied in Australia. Up to now it was mainly used in coal surface mining at the Australian East- Coast. Presently, the proved results reach ~ 50 % reduction of Drilling & Blasting costs and a productivity increase of between 10 and 20 %. In 2003 it was for the first time used in surface metal-mining. The mine features for the time being an extremely difficult geological environment and had above to be carried out in the transition level waste/ore. Reductions of wall control, powder factor and vibrations were the main target.

Jan 1, 2004

By Nickolas Vlahopoulos, Nicholas Stowe

A concept has been proposed for the focusing of underwater energy. An array of spherical TNT charges is used to achieve this aim. The goal of the present research effort is to model such a system and identify optional arrangement and detonation timing schemes. A fast-running model is necessary to perform optimization analysis due to the highly iterative nature of most optimization algorithms. This requirement renders the use of sophisticated numerical solvers impractical. An analytical, physics-based model must be developed to satisfy the demands of the multiple charge optimization problem. This model must capture shock propagation speed, pressure-time histories throughout the fluid domain, and multiple charge interaction phenomena. Such a model is presented herein.

Jan 1, 2012

By Hairong Zeng, Shahram Tafazoli, Edmond Chow

Blast fragmentation is one of the main parameters for optimizing mineral processing, but reliable data is difficult to acquire, resulting in unpredictable performance and efficiency. Crusher and grinder circuits are designed to process specific rock size ranges. Oversized rocks require extra energy to reduce before feeding into the process, and undersized rocks indicate that the process is not used to its full extent. Blast design is the key to controlling the blast fragmentation, so the ability to accurately monitor the particle sizes is imperative.

Jan 1, 2011

By Greg S. Williams, David L. McDorman, Richard W. Givens

This paper examines the effect of prill size consistency, internal particle density, and oil absorbency on Ammonium Nitrate Fuel Oil (ANFO)-emulsion blends. By analyzing these physical properties of prill and the nature of the blending process, a mathematical model has been developed to theoretically predict blend densities. Calculated densities can now be compared to actual field densities to give an operator a basis for comparing various manufacturers' emulsions and Ammonium Nitrate (AN) during bid solicitation. The lowest priced emulsion and/or AN may not be the most economical, due to the impact of specific physical characteristics. These factors dictate the blending mechanics and resulting density yields for various mixes. The research was driven from observed 'field' mixing relationships and data. Ultimately, such a model can be an effective tool in evaluating blends from a cost and performance basis.

Jan 1, 1990

By David E. Siskind

U.S. Bureau of Mines Report of Investigation 8507 was published in 1980. In a comprehensive analysis of all known blast damage studies plus new definitive data, the USBM authors adopted new safe level criteria of 0.5 & 0.75 in/sec for the frequency range corresponding to structure resonances. These were 3 to 4 times lower than the existing limit of 2 in/sec and are the most restrictive scientifically-based blasting criteria for the prevention of threshold hairline cracks in homes. The Bureau's own tests involved 76 homes in six states. In USBM RI 8507, those tests were combined with data from nine other studies from the US, Canada, Czechoslovakia and Sweden in an overall conservative summary analysis intended to preclude blasting damage.

Jan 1, 1998

By Muhammad Yamani, Marsell Riviera, Herry Saputra, Rizky Amin

Drill and Blast processes in hot and reactive ground conditions are a severe challenge in mining, especially in the blasting process. Our main objective is safety issues without compromising the blasting outcome. Safety concerns include unexpected detonation, product damage, and misfire. However, apart from the issue of blasting safety, it is also crucial to maintain good results such as fragmentation, loader productivity, and ore dilution control. Therefore, we use a different product selection method to produce a safe and efficient blast. Pit Araren is one of the pits of the Tokatindung Gold Mine Project in North Sulawesi Province, Indonesia, classified as hot and reactive ground conditions that range from elevation of 25mRL temperature could reach to 98⁰C (208,4⁰F) based on actual measurement. The previous practice for blast holes with temperatures above 70⁰C (158⁰F) loaded with the primer that was specifically designed for hot and reactive ground conditions consisting of detonating cord and packages emulsion that specifically formulated to inhibit exothermic reaction then tied in with a combination of non-electric surface delay detonator and detonating cord initiator (short length non-electric surface delay detonator housed in plastic connector).

Feb 6, 2023

By Javier Illanes Pizarro, Gustavo Huerta Valer, Jorge Cárdenas Miranda

Bench stability is the basis of sustainability in an open pit mining operation. Taking care of the pit walls while maintaining fragmentation results can prove a challenge. In this study, technical proposals have been developed for extra hard rock mass (UCS>175MPa) with presence of unfavorable structural planes in high copper grade zones. The base case shows low compliance of fragmentation results and a significant loss in berm width, with over size boulders causing low primary crushing rates. Paradigms in current drill and blast design were overcome to improve fragmentation results and achieve objectives.

Feb 6, 2023

By Adrian Moore, Bryan Goodwin, David Fales, David Lam

This paper describes the development of blasting protocols used to successfully create a 450m long blast fractured permeable trench in a basalt aquifer up to 20m thick, at a petrochemical facility in Australia, to enable the remediation of contaminated groundwater.

Jan 1, 2011

By Blair Jackson, Tjaart Louw

Martha Mine, owned by Newmont Mining, Australia appointed Macmahon Contractors (NZ) Ltd as the mining contractor to drill, blast, and crush and convey ore for processing, followed by construction of a tails dam facility from the waste material. The open pit is located 140km(90miles) south east of Auckland, New Zealand in the middle of the township of Waihi (the main street of the town with a population of 3,500 is 90m from the perimeter of the open pit mine). Mining must proceed at 325,000m3 (of which involves blasting approximately 11,000 holes per month, in order to ensure continued ore supply.

Jan 1, 2003