Search Documents

By Edward L. McHugh, Stanley M. Miller, Jeffrey K. Whyatt

The point estimation method can be applied to the safety factor (SF) equation for any specified rock slope failure mode (such as plane shear, step path, or wedge) to obtain reliable estimates of the mean and standard deviation of the SF probability distribution. A gamma probability density function is recommended for modeling this probability distribution, because it allows only for positive values and is flexible enough to provide symmetrical shapes and right-skewed, exponential-type shapes for the SF distribution. The mean and standard deviation define this distribution, which then can be integrated numerically from 0 to 1 to obtain the probability of sliding, PS (portion of the SF distribution where SF < 1.0). The overall probability of failure, PF, for the potential slope failure mass is the joint probability that the rock discontinuities are long enough to allow kinematic failure (PL) and that sliding occurs along the rock discontinuities (PS); that is, PF = PSPL. This method for estimating the probability of sliding is extremely efficient computationally, and thus, expedites slope stability simulation routines used by NIOSH software to stochastically describe rock slope behavior and assist the engineer in designing catch benches for large rock slopes. Enhanced bench design translates into increased operational efficiency and safer working conditions in open pit mines and quarries.

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By H. J. Lechtenberg

Preliminary results are given of solvent stimulation of two wells producing viscous oil (14°-17° API) from the Tar zone in the Wilmington field, California. The solvent (coker oil, an intermediate refinery product) was injected into the formation, and after a soak period, the well was returned to production. Data are given on crude oil properties, solvent properties, determination of volume of solvent in the produced oil, rate of oil production before and after stimulation, volume of additional oil produced, and volume of solvent recovered. Although further study and improvement of the method arcs needed, cyclic solvent stimulation appears to be an unqualified success in one well and a moderate success in the other.

Jan 1, 1972

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

By R. R. Sayers

"The number of investigations reported during the past year indicates that control of the health hazard due to abnormal air conditions is still a matter of serious consideration in the mining, metallurgical, and allied industries.Australia. - In an investigation into the health and working conditions of employees in the mining industry of Tasmania and Victoria3, it was found that although pulmonary tuberculosis may occur early in life, silicosis is e disease of slow evolution and does not appear frequently under the ace of 40. A period of at least ten years in the industry was found necessary to produce silicosis, and in no case was the disease found in those who had not worked underground. A very high incidence of silicosis was found in all fields among those who had worked underground 20 years and longer. There was some evidence that silicosis complicated by tuberculosis may occur earlier than uncomplicated silicosis.England. - In a paper presented before the Section on Occupational Diseases of the British Medical Association, Dr. E. L. Middleton, the medical inspector of factories, called attention4 to the occurrence of silicosis in various industries throughout the country.punitive on some quite harmless industries. Thus Middleton says: ""Where the amount of dust is small the action of the phagocytes is likely to be effective, but where it is great . . ."" What dosage is indicated by ""small"" and ""great"" in this connexion? If the meaning of ""small"" were known, would it be correct to go on to say, as he does, ""each successive dose of silica produces a summation of effects""? Then, again, would it be fair to say ""a comparatively brief period of exposure may be the only determining factor""? What, in minutes, hours, or days per week, per month,' or year, is intended by ""a comparatively brief period""? ""Intermittency of the process"" is another expression used in summing up the reasons for and against a standardization of air purity by a gravimetric process or enumeration of the particles; the arguments against such a standardization are, by Middleton, considered strong, but they are by no means convincing to us. A standard has been accepted in respect of the amount of lead in milligrams per 10 cubic metres of air; Dr. Ronald Lane showed in another paper read that adherence to this makes the occurrence of poisoning highly improbable. Mavrogordato has placed on record figures of silica dust at different stages of the improvements in the workings of the Rand mines, and such a control is in constant operation in them today.We emphasize these points because apparently the Government has taken the unusual course of legislating first and postponing inquiry to a later date, as in the ""Various Industries (Silicosis) Scheme, 1939."" The insurance companies also have a considerable interest in the matter of compensation for the silicosis risk. Where exposure - as in the refractories industries, the grinding industries, sandstone industry, and pottery industry - is day in and day out, they rightly demand a premium far higher than for any other disease scheduled under the Workmen's Compensation Act - 5 per cent on the wages bill. row every industrial employer, such as the paint and varnish manufacturer, who has a sack of crushed silica in his store .room, from which he extracts once a week enough to make a paste With spirit and add to his other ingredients in order to give them the necessary ""bite,"" becomes involved, and may have to abandon the use of the material or pay 8 per cent on his wages bill for an absolutely negligible risk.. For meting out justice standardization seems urgently called for."

Feb 1, 1930

To provide an engineering solution to wood crib design and deployment strategies that will ensure safety for underground coal mine workers. This is accomplished by preserving necessary ground control requirements while minimizing support costs or by developing new support strategies to enhance ground support in difficult conditions. A secondary objective is to be able to quantify wood crib support performance to define support requirements for alternative support systems. These objectives have been achieved through a simple-to-use computer program called the wood crib performance model (wcpm).

Jan 1, 1997

By W. H. Ode

Because trade increased among various nations after World War II, the Coal Committee of the Economic Commission for Europe established a Classification Working Party in 1949 to develop an International system for classifying coal. Although national classification systems existed, they had been developed in accordance with characteristics of domestic coals without reference to coals of other countries. Terms for describing similar or identical coals differed in each nation. This caused confusion in evaluating coals shipped in international trade and also hampered exchange of technical information on problems of coal utilization. Experts4/ participating in the classification project early in their work agreed that two systems should be formulated, one for the higher rank coals or so-called "hard" coals in European terminology and the other one for the lower rank coals, the latter designated mainly as brown coals and lignites in the various countries. Rank refers to the degree of metamorphism (progressive alteration) in the natural coalification series from lignite and brown coal to anthracite. The system for classification of hard coals was published late in 1956 as a document of the United Nations.5/ Results of a study for applying this system to American coals were published in 1958.6/

Jan 1, 1960

"INTRODUCTIONThe information compiled in this volume initially formed the response by the Generic Mineral Technology Center for -Respirable Dust (GTCRD) to a review of its research and technology transfer programs performed in 1990 by the Advisory Committee on Mining and Mineral Resources Research. This review for each mineral technology research center is accomplished, as required of the Bureau of Mines by the House/Senate Joint Conference Committee, through site visitation to the research institutions of the GTCRD and an in-depth questionnaire. The information provided by that questionnaire becomes an important factor in their recommendations concerning future directions of the program.The site visitations took place during January and February 1991 at the Milton S. Hershey Medical Center~ The Pennsylvania State University, West Virginia University, University of Minnesota, and Michigan Technological University, in addition to an in-mine visit conducted at the Loveridge Mine in West Virginia. The questionnaire was prepared and made available to the Advisory Committee and the Research Council for their review at the GTCRD annual project review meeting in Hershey, Pennsylvania, in April 1991.The comprehensive nature of the questionnaire and the scope of the information contained therein make it an excellent retrospective of the Center. Having a clear vision of where the Center has been and knowing where it is now helps to guide it into the future. It is believed that such a detailed view of the Center's facilities and research program will be of value to Center personnel and Advisory Committee members. Each aspect of the questionnaire was examined, answered in detail and documented thoroughly. With the completed questionnaire as a guide, this review of the Center's activities provides an update to Respirable Dust Center Research Program Review 1988, published in 1989 as the seventh of the Generic Mineral Technology Center for Respirable Dust volumes. As does that volume, this review presents the complete General Mineral Technology Center questionnaire, with the GTCRD's expanded responses and supporting documentation appended. An examination of the research program, Center personnel currently active on GMTC projects, the number of graduate degrees granted with GMTC supports GMTC publications, the degree of individual interaction, technology transfer activities, the reference center, GMTC equipment and facilities, and envisioned plans for future research directions provides updated information in these areas. In addition, this year, information has been included to demonstrate the interaction between the Center's goals and its research projects, with thorough consideration of actual research needs as specified by the National Academy of Sciences. This volume serves as a review of the years 1989 through 1990, the sixth and seventh years of the Center's operation."

Jan 1, 1990

By J. B. Janus

In connection with the purchase of coal under specifications for Government use, the Bureau of Mines in this report has compiled data on 81 mines located in 15 States. This annual report lists analytical data on the composition and quality of tipple and delivered samples of coal collected during fiscal year 1973. Tipple samples were collected by Bureau of Mines engineers at tipples as coal was being loaded into railroad cars or trucks. Ultimate analyses are given for most of the coalbeds listed. The deliveries were sampled at destination in accordance with instructions issued by the Bureau of Mines. All samples were analyzed in the Bureau laboratory at Pittsburgh.

Jan 1, 1973

By H. F. Coward, G. W. Jones

"IntroductionIn the course of an investigation on the influence of black damp (a mix of nitrogen and carbon dioxide) on the limits of inflammability of fire damp (methane) in air, some new information was obtained concerning the factors that determine whether or not a gas mixture is capable of self-propagation of flame. Volume for volume, carbon dioxide exceeds nitrogen in its extinctive action on flame, an effect which is generally attributed to the higher molecular heat capacity of the former. Argon, a as of lesser heat capacity than either, proved to Lave less extinctive notion. If, as seemed likely, the extinctive action of a chemically inert gas could be attributed entirely to its heat capacity, then helium should behave like argon; equal volumes of these two oases should exhibit equal extinctive action, for their molecular heat capacities are nearly identical at laboratory temperatures and, in all probability, remain constant up to and beyond flame temperatures. The experiments reported here show, however, that helium has proved to be more extinctive of methane flames than argon.Method Used in ExperimentsThe limits of inflammability of methane, in various ""atmospheres"" composed of mixture of air with one or other of the diluent were determined in a vertical glass tube, 6 feet long and 2 inches in diameter. The lower end of the tube was opened by sliding away a ground-glass joint and the flame of a small spirit lamp was immediately passed across the aperture. The tube was sufficiently long to enable observers to judge whether a flame was self-propagation for if a mixture were incapable of continued self-propagation pf flame, the lamp of flame formel above the source of ignition was extinguished within feet of its passage up the tube."

Jun 1, 1926

By S. Stephen Uslan

The purpose of the study was to demonstrate the effect of positive reinforcement, specifically, social reinforcement (SR), on the frequency of eye, hand, and back injuries at four experimental salt mines. Injury data was collected from January, 1976, for the prePOMOST period and from the onset of training to September, 1978, for the post-POMOST period. All data was collected on a month-by-month basis. For the training period approximately 100 managers and supervisors from five plants were trained in the use of positive reinforcement for occurrences of "safe behavior." Each supervisor was also provided manuals and other supportive materials. Additionally, following training, all supervisors were provided some coaching experience to keep the knowledge and capabilities gained during training from being extinguished. The analysis showed significant injury reductions in two sites and no injury reductions in the other two. When the injury data was corrected for the additional man hours expended in the postPOMOST period, a third site showed reduction in injuries. Similar findings were shown when the experimental sites were compared to other sites in the industry. The results were interpreted to support the hypothesis that the application of social reinforcement is related to a reduction in injuries.

Jan 1, 1978

By W. W. Adams

The extent to which coal mines have installed various types of haulage systems and mining machines is a subject about which there is little definite information available in convenient form for the country as a whole . A few State mine inspectors include in their annual reports such information for their respective States , but uniform data for the United States have not until recently been compiled . Several years ago the Bureau of Mines compiled from one of the standard mining directories * a statement showing the kinds of machines and haulage used in coal mines . The first statement was prepared from the 1918 edition of the directory in which detailed descriptions of coal mines were given . The information presumably related to the calendar year 1917. Similar statements have been compiled from the directories for 1919 , 1920 , and 1922 , the statement for 1921 having been omitted because the directory for that year did not become available . The latest statement is given below and is based upon the directory for 1922. It relates to conditions prevailing in 1921 , and covers a total of 7,088 coal mines . Of these , 5,064 mines . or more than 71 per cent , were using animal haulage . As compared with the total number of all classes of mines , those in the animal - haul age group constituted 71.4 per cent , the percentage having remained practically stationary during the past four years , although the actual number of mines in the group has increased . Rope haulage was reported by 1,066 mines , or 15 per cent of the total , representing a larger number of mines than in 1918 , but a decrease of 2 in the percentage for the group as compared with all classes of mines . Electric haulage was reported by 3,274 mines (46.2 per cent ) , and the number of motors in use was 11,265 . The percentage of mines in this class has not changed materially, but the actual number of mines has shown a gain of about 900 during the past four years . Compressed-air locomotives have not increased either in actual or relative number , the percentage for the past year being but 1.2 . The number of mines using storage- battery locomotives has increased from 3.6 per cent of the total shown four years ago , to 9.8 per cent for last year, the latest figures showing 693 mines with 1,428

May 1, 1922

By N. A. Eilertsen

Among the numerous Low-grade manganese deposits in eastern Aroostook County, Maine, the Dudley deposit near Mapleton in the northern district is one of the few known to contain an appreciable tonnage averaging above 10 percent manganese. The ore body, consisting of stratified manganiferous hematitic shale, is over 5,000 feet long and ranges in width from 30 to 175 feet. The deposit was extensively explored during 1942-44 by the Manganese Ore Co., a subsidiary of M. A. Hanna Co. of Cleveland, Ohio. Data obtained from this work were made available to the State and Federal Geological Surveys for estimating ore reserves. An estimate by the Maine Geological Survey, using a 10-percent manganese cutoff and to a depth of 200 feet, shows 609,000 long tons of manganese metal in material averaging 12.6 percent manganese. By lowering the cutoff limit to 5 percent manganese, the estimate was increased to 919,000 long tons of metallic manga¬nese in material averaging, 10.4 percent manganese,

Jan 1, 1957

By Richard J. Mainiero, James H. Rowland III, Marcia L. Harris

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NOx). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed. These include: • Minimizing the quantity of toxic fumes produced. • Determining where the fumes may go so workers and neighbors can be moved out of harm’s way. • Preventing the fumes from moving towards workers and neighbors. • Monitoring the air near workers and neighbors so they can be relocated if fumes appear. • Ventilating structures or confined spaces until CO falls below a hazardous concentration.

By G. W. Jones, R. E. Kennedy

"INTRODUCTION In the manufacture, storage, transportation, and use of combustible gases and vapors, explosion hazards, which at times may be present when air becomes mixed with the gases and vapors, become of primary importance. Such conditions are especially dangerous where large volumes of gaseous atmosphere are involved, because an explosion under such circumstances is capable of doing tremendous damage to both property and personnel.Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated, and published results dealing with, the explosibility of various types of combutible atmospheres. The explosion hazards of natural gases have received attention, and results giving the limits of inflammability and ignition temperatures in air have been determined and published. 4/ Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide. 5/Because of the increased demand for crude oil for war purposes, the application of secondary-recovery methods of stimulating oil production have received considerable attention during the last few years. The process consists in the injection of natural gas into partly depleted oil wells to cause the oil in the sands to flow into producing wells and so increase the amount of recoverable oil. 6/"

Feb 1, 1945

By Joseph S. Coffman

To determine the availability of manganese for metallurgical purposes from selected world resources, the Bureau of Mines evaluated the potential production of contained manganese in concentrates based on the demonstrated resources of 23 foreign and 8 domestic mines and deposits in 9 market economy countries. All but 2 of the 23 foreign deposits are operating mines; none of the domestic deposits are in operation. The demonstrated resources of the mines and deposits used in this study represent an in situ ore resource of approximately 2.2 billion tons," containing 780 million tons of manganese with a total recoverable production potential of 514 million tons of contained manganese in concentrates. The analyses of mines and deposits in this study indicate that about 213 million tons of the contained manganese (41 pct) is potentially available at a January 1981 constant dollar long-run total cost of up to $1.50 per long ton unit (22.4 lb, or 10.15 kg contained Mn), approximately 428 million tons (83 pet) is potentially available at a cost of about $1.75 or less, and 491 million tons (95 pet) is available at less than $3.30. The remaining 23 million tons, which is potentially available at much higher costs (about $8 to $35 per unit), represents the U.S. deposits. On an annual basis, with a cost range of up to $1.75 per long ton unit, the availability from currently operating mines would last at least 80 years based on 1980 world production data. Total manganese production costs are estimated to comprise mining-8 pet, beneficiation-3 pet, transportation-26 pet, and smelting-63 pet.

Jan 1, 1984

By L. C. IlsLey

The theory and practice followed by the Bureau of Mines in investigating electrical equipment4/ made for service in gassy mines are of particular interest not only to manufacturers but also to those organizations that deal with safety anal inspection at the mines. This publication purposes to discuss the theory upon which tests of equipment in explosive atmospheres are based and to consider inspection and other matters pertaining to investigations made by the Bureau in ascertaining whether a machine merits approval. The material in this report is taken from an earlier bulletin,5/ which is row out of print, and has been revised and brought up to date to make the information again available to manufacturers, inspectors, and others interested in the development of safe equipment.

Jan 1, 1954

By Stephen C. Tadolini, Thomas E. Marshall, Cecil Banta, L. J. Prosser, Anthony T. Iannacchione

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) endeavors to provide national and world leadership in the prevention of work-related illness, injury, and death. This is accomplished by using a scientific approach to gather information, assemble and create knowledge, then translate the knowledge and results into products and services. These products and services are then delivered to all personnel who can effect prevention. Obviously, the development and use of instruments to monitor mine roof conditions provides an opportunity to execute that mission. In the late 1990’s, based on observations at a number of underground limestone mines, only a few used roof monitors. Subsequently, NIOSH introduced the Roof Monitoring Safety System (RMSS) as an aid to roof inspection beyond traditional visual and sounding techniques. Initial expectations were that by gaining roof movement information, ultimately roof sag rates could provide indications of eventual failure. During this investigation, RMSSs were installed in 13 underground limestone mines in six states and this paper analyzes the data obtained at three of these mines. This paper also provides an overview of the system, data, analysis, and applications relevant to the RMSS.

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.