Search Documents

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By Thomas M. Barczak

Roof support technology for longwall tailgates has changed dramatically during the past decade. Filling tailgates with conventional wood cribs is becoming the exception rather than the rule. Modern engineered timber support systems and a host of other alternative support products provide far greater capacity as well as stiffer response, thereby allowing the supports to resist roof movement with much less displacement than the soft wood cribbing used in the past. For these reasons, these products can provide superior roof control. In addition, the material handling requirements for support installation have now become a major consideration in the support design and selection process. Products such as conventional wood cribbing that require piece-meal construction of bulky, heavy components have diminished, while prop-type supports and products that can be installed with machinery and pumpable support technologies have grown in use resulting in fewer injuries to mine workers. Now, the opportunity exists to provide the safest, most cost effective support system, through engineering design rather than by trial and error and to optimize the use of the support system chosen. Yet this is rarely done. The key to accomplishing this task is to understand the interaction of the support system with the ground conditions at the installation site. A major focus of the paper is to conceptualize the support and interaction through the use of a ground reaction curve which relates the support resistance to the convergence of the longwall tailgate. The goal of any roof support design is to control the ground deformations and maintain the structural integrity of damaged or broken ground to the extent possible to provide a stable mine opening. In general, deformations will be a function of the stress environment and inherent strength of the surrounding rock mass. However, if the deformations are intimately linked to the stress changes such that the deformation can be controlled by the load resistance or reinforcement provided by a roof support system, then the loading behavior can be described as load-controlled. Conversely, if the deformation occurs irrespective of the installed support (assuming practical limitations), then the loading behavior is described as displacement-controlled. In this case, the deformation can be considered irresistible from a practical standpoint. In this context, the nature of the loading has significant consequences on the support design requirements. Finally, examples using the NIOSH Support Technology Optimization Program (STOP) to develop design criteria using ground reaction data from underground studies and ways to include uncontrolled convergence as part of the design criteria for standing roof supports will also be discussed.

By Eleanor Abshire

THIS PUBLICATION is the third to be prepared as a result of a cooperative project by the Bureau of Ships and the Bureau of Mines for accumulating literature published on zirconium and hafnium. The undertaking also resulted in the establishment of an information center on zirconium and hafnium at the Bureau of Mines station at Albany, Oreg., for the use of research organizations and others. The present bibliography consists of references (with abstracts) to pertinent literature on zirconium. The first publication in this series was Information Circular 7771, Bibliography of Zirconium, published in April 1957. It consists of 969 abstracted reports and 645 U.S. and foreign patents. The second publication, called a supplement to Information Circular 7771, is numbered Information Circular 7830 and consists of 844 abstracted reports and 62 U.S. and foreign patents. It was published in October 1958.

Jan 1, 1962

By R. W. Dougherty

From time to time interest has been evidenced in transporting coal with water in pipe lines. About the year 1895, United States patents broadly covering a method of pumping coal with water through pipelines were granted to W. C. Andrews. His process was used to some extent in pumping anthracite culm and waste back into the worked-out portions of the mines. About 1905, W. T. Donnely was granted patents relating to pumping anthracite silt away from the breakers. From about 1913 until 1924, a British engineer, Gilbert G. Bell, used a short pipeline to convey coal with water from barges on the Thames River to the Hammersmith Electricity Generating Station, London. Minus 5-inch coal was transferred 660 yards through an 8-inch pipe. Some trouble was experienced with fine coal, which tended to plug the line. Bell made several proposals to transport coal by pipeline overland from the Midlands to London, a distance of about 100 miles, but these were never adopted. This survey is concerned mainly with the problems presented by actual pipeline transportation of coal with water. It is assumed that the coal will have been processed to remove most of the abrasive impurities by conventional methods prior to introduction into the line, and that it has been crushed to the required top size. Dewatering at the discharge end of the line is considered part of the conventional cleaning process. There still remain many pump-performance and behavior of water-coal mixture problems that can be solved only by actual performance tests. It is recognized that the distribution of coal to other than very large users is not changed. Large storage areas would be required to supply seasonal markets. Large users, such as power plants and heavy industries, could be supplied by branch lines directly to the point of use, It is also recognized that pipe lines might not be able to carry a full range of sized coal to meet market demands in many areas.

Jan 1, 1951

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

C THRM 1 C CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA TURN 2 C PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT THRM 3 C THRM 4 C THRM 5 C THIS PROGRAM CALCULATES PRESSURE LOSSES USING THERMODYNAMIC RELATION- THRM 6 C SHIPS BASED ON POLYTROPIC FLOW BETWEEN STATIONS. FOR REFERENCE SEE THRM 7 C "A NEW TREATMENT OF MINE BAROMETER SURVEYS" BY M. J. MCPHERSON IN THRM 8 C 'THE MINING ENGINEER' NO. 109, VOL. 129, P 23. THRM 9 C THRM 10 C THRM 11 C THRM 12 C IDENTIFICATION OF ARRAYS THRM 13 C NOTE THE PROGRAM HAS BEEN DIMENTIONED FOR FOURTY (40) DATA POINTS THRM 14 C BASEC(6;2) BASE INSTRUMENT TEMPERATURE CORRECTIONS THRM 15 C TRAVC(6,2) TRAVERSE INSTRUMENT TEMPERATURE CORRECTIONS THRM 16 C BASER(I) BASE INSTRUMENT READING THRM 17 C TRAVR(I) TRAVERSE INSTRUMENT READING THRM 18 C TDRY(I) DRY BULB TEMPERATURE AT TRAVERSE STATION THRM 19 C TWET(I) WET BULB TEMPERATURE AT TRAVERSE STATION THRM 20 C ELEV(I) ELEVATION AT TRAVERSE STATION THRM 21 C VEL(I) AIR VELOCITY AT TRAVERSE STATION THRM 22 C TBDRY(I) DRY BULD TEMPERATURE AT BASE STATION THRM 23 C BASC(I) BASE READING CORRECTED FOR INSTRUMENT TEMPERATURE THRM 24 C TRAV(I) TRAVERSE READING CORRECTED FOR INSTRUMENT TEMPERATURE THRM 25 C BBASE(I) TEMPERATURE CORRECTED BASE READING IN BAROMETRIC THRM 26 C PRESSURE THRM 27 C BTRAV(I) TEMPERATURE CORRECTED TRAVERSE READING IN BAROMETRIC THRM 28 C PRESSURE THRM 29 C BTRAVS(I) BAROMETRIC TRAVERSE READING CORRECTED FOR ATMOSPHERIC THRM 30 C CHANGES THRM 31 C RELHUM(I) RELATIVE HUMIDITY THRM 32 C ASW(I) AIR SPECIFIC WEIGHT TURN 33 C R(I) GAS CONSTANT FOR MOIST AIR THRM 34 C STPRES(I) STATIC PRESSURE CHANCE BETWEEN STATIONS (I) AND (1-1) THRM 35 C TOPRES(I) TOTAL PRESSURE CHANCE BETWEEN STATIONS (I) AND (I-1) TURN 36

Jan 1, 1977

By J. W. Paul, J. N. Geyer

"GENERAL STATEMENTThe purpose of this report, which is the first of a series of three covering mines in the Fairmont district of West Virginia, is to give the result of a' study conducted in seal mines to ascertain the nature of the safeguards employed to prevent injury to the workmen from falls of roof and coal. In presenting the subject matter, consideration must necessarily be given to factors, features, and conditions such as method of mining, timber regulations and practices, supervision and natural conditions; and, for comparative purposes, a certain amount of statistical matter bearing upon the relation of fatalities and injuries to their causes, tonnage produced, men employed, days worked, and time lost.Those features and practices found to promote safe protection are summarized and suggestions made for such additional safeguards and practices as appear to give greater protection against injury from falls of roof or coal.ACKNOWLEDGMENTSThis study of falls of roof and coal in mines in Harrison County has been conducted by the U. S. Bureau of Mines in cooperation with R. M. Lambie, chief of the Mining Department of the State of West Virginia who assigned L. W. Brown, a district mine inspector, to assist in the field work and in the preparation of individual reports on each mine visited in this study. The writers acknowledge the helpful suggestions and cooperation given by these officials, the latter of whom assisted in the field work and prop red most of these sketches for the individual reports which wore submitted to the operator by the chief of the department. Thin report is a summary of the contents of the individual reports heretofore furnished the individual operator."

Aug 1, 1931

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

The accompanying supply/demand flow diagrams and 10-year tables for mineral and fuel commodities present essential data required by government, industry, and others to formulate policies and programs that can help assure an adequate and continuing supply of mineral raw materials. The 10-year data base terminates with 1973 figures because adequate world information was not available beyond that date. Moreover, 1974 was an anomalous year with respect to prices, supply, and demand for many commodities. The selected mineral supply/demand tables and flow diagrams comprise but one "output" from the massive body of "information and data collected and com-piled by the Bureau of Mines on a continuing basis covering mineral production consumption, prices, shipments, imports, exports, and stocks, as well as industry activities in all States and abroad.

Jan 1, 1975

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,070 Bcf as of January 1, 1985. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 280 Bcf, (2) helium in probable natural gas resources, estimated at 243 Bcf, (3) helium in possible natural gas resources, estimated to be 287 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 260 Bcf. These helium resources are further divided into depleting, non-depleting, and stored classifications. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 900 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 133 Bcf. There is 37 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1987

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By William E. Eckard

Production of oil from a narrow shoestring sand presents problems unique in the oil industry. Especially important, from both an engineering end an economic standpoint, are the limitations imposed upon well patterns and spacings by the shape of the field. This report concerns a study of the Paola shoestring, Miami and Franklin Counties, Kane., where well density of 0.85 acre per well was not uncommon to insure profitable primary recovery in a reasonable time. However, such a great number of wells increased the operator's investment and reduced his profit considerably. It was the purpose of this study to investigate various well patterns and spacings applicable to water-flooding a shoestring reservoir and the effect of these factors upon recovery of oil and the most profitable operation of the pool. The designer of well patterns for a shoestring sand should evaluate carefully the edges of the shoestring, even though they may be considered too thin to drill. These comparatively thin edges contain large quantities of recoverable oil; moreover they are resaturated with oil as the pool is water-flooded.

Jan 1, 1951

By Richard L. Fowler

Study and development of sensing techniques and sensors were performed to aid shuttle car drivers in detecting obstacles and in guiding the car along the face haulage route. Microwave, acoustic, and optical sensing techniques were considered as part of the feasibility study for obstacle detection. Various guidance techniques, including wire-following and rib-ranging were investigated. Active optical sensing was selected for obstacle detection to obtain the beam coverage and sharp angular cutoff characteristics required within the packaging limitations defined by the shuttle car configuration. Rib-ranging guidance was selected to achieve a completely self-contained shuttle car system which responds to the existing mine geometry without need for wires, stripes, or other path defining devices. Extensive hybrid computer simulation runs were performed to evaluate various guidance techniques during the feasibility study. Subsequent simulation runs were performed to establish parameter values for the rib-ranging guidance system. The obstacle detection and guidance system was designed, fabricated and installed on a standard shuttle car. The system satisfied all applicable permissibility requirements of Schedule 2G. An experimental permit was issued to Bendix for operation in an underground coal mine. System evaluation tests were performed first above ground at the Bendix Research Laboratories. The simulation model was validated by these runs. Final testing was performed underground in an operating mine with an experienced shuttle car driver. All sensors successfully demonstrated the predicted performance capability during underground face haulage tests. Dust did not impair system performance and lens cleaning was not required during working shifts. Further development is required to achieve the desired obstacle detection performance. Closed loop steering control with manual override is recommended for the lateral guidance system. The guidance system should be an invaluable aid to low-coal shuttle car drivers where continuous mining machines are utilized.

Jan 1, 1973

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health are investigating technologies that could be used to detect objects, small vehicles, and pedestrian workers that may be in the blind areas of haulage equipment used in mining and construction. A detection system that warns the equipment operator that there is an obstacle nearby could prevent collisions and save many lives each year. One popular technology for collision warning systems is radar. Several different types of radar have been tested in the laboratory and on mining equipment. Early in the study, questions arose concerning the best way to test radar systems. Many factors affect the performance of radar, including the size, shape, and composition of the object that is to be detected; the height of the radar antenna(s); and the relative motion of the radar system and/or object. This report discusses several different test procedures and test targets and recommends methods to determine how effective a radar system will be in detecting a person near heavy equipment.

Jan 1, 2002

By Stephen C. Tadolini, Raymond A. Mazzoni

The International Ground Control Conference in Mining has always provided an open forum for the publication, presentation, discussion, and often heated debate on roof bolting systems mostly with attention to how, when, and why they work. During the last 24 Conferences at least 170 papers have been presented by International Experts on these “simple” devices that range in length from 30-inches to 20 ft and from 5/8 to 2 inches in diameter. Roof bolts are primarily mechanically anchored, glued, cemented, or driven. Bolts are placed vertically, angled, or tied together with special fixtures (trusses and slings). They have been termed active, passive, stick-slip, and several other descriptive acronyms or mining slang expressions. This retrospective paper will present the changes in bolt types and usage, point out some of the biggest myths and hail the most significant advances (according to the authors’ opinions of course).