Search Documents

By William R. Vogel

The Bureau of Mines Information and Analysis organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 3291, to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1989

By Bruce E. Stauffer

The report recommends criteria for the design of safe surface mine haulage roads. Information relevant to road design at surface mine sites delineates vertical and horizontal alignment; subbase and surface materials; drainage; cross-slope, superelevation; runaway vehicle protection; and road and vehicle maintenance criteria. An appendix Is included which details the study methods used in compiling the final report information. A bibliography following the main text lists literature referenced for the report data and which is available as a valuable tool for use by individuals involved in haul road design.

Jan 1, 1976

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

By J. H. Jones

The original term of grant No. 1115174 was September 1980 through December 1983. An extended progress report, covering this time period, was forwarded to the Bureau of Hines in January 1984. The principal investigators were given a no-cost extension of their grant to cover the period January through December 1984. The report which follows covers this latter time period only.

Jan 1, 1985

Reduce the danger to personnel and destruction of equipment caused by fires on surface coal augers. Approach: A reasonably priced reliable system which automatically senses a fire and activates dry chemical extinguishers, has been built and field tested. How It Works: Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system.

Jan 1, 1976

By C. A. Herbert

The mine of the Alpha Portland Cement ..Co., Iroaton, Ohio, ..working in. a. bed of limestone 96 feet thick at a depth of approximately 510 feet below the surface, has established a won¬ derful safety record, having operated 6 years—frcra September 21, 1926,. to September 21, 1932 - without a lost-time accident. This mine, with 61 to 86 employees (average 68) and daily output of 1,000 to 1,200 tons of limestone, operated 1,041 days during the 6-year period, or the equivalent of 578,894 man-hours of exposure. ...... ... . Immediately above the limestone is a 20-foot .bed of hard..sandstone.. At present about 10 feet of limestone is left up as. a roof and.about. 42 feet is being extracted. Of the lower portion of the bed it is believed that about. 25 feet. ..immediately below . the .present workings is suitable for cement and will be extracted later. The mine workings are reached by two rectangular concrete shafts, one a 2-compartment hoisting shaft and the other a 2-compartment air and escape shaft- In the latter shaft one compartment is used as an airway and the other, as a cage compartment fo.r a man and material cage. .. . - . The tipples at both the air shaft: and. hoisting shaft are-of steel. The.ground landings at both shafts are fenced in with hand-operated gates in front of the cage compartments.- The two shafts and the crushing plant, which .is.a part of the hoisting shaft-tipple structure, are adjacent to the mill buildings. The rock is hoisted on self-dumping cages in 4 ton capacity, end-gate, steel cars. An electric hoist with automatic overwind device is used at both the main shaft and air shaft. The controls for the main hoist are in the tipple where the engineman is stationed and from which point he has an unobstructed view of both the ground, landing and the cage coming into the dump.

Jan 1, 1933

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By George A. Morgan

The successful expansion of crude oil production begun in late 1977, led to promising development of the nonfuel minerals sector. Although actual production of nonfuel minerals was limited both in variety and in percentage of output on a world scale, the potential for expansion with a rapidly developing infrastructure was significant. The energy base was expanding with construction of two new hydroelectric powerplants in addition to the existing plant near Edea. The Song Loulou plant will have a 240-megawatt capacity, and a hydroelectric plant under construction in the northern part of the country by mainland China will have 72 megawatts of installed capacity. Inflation of between 15% and 20% resulted in a real gross domestic product (GDP) of $2.8 billion2 in fiscal year 1980 (July 31 to June 1), up 6% from that of the previous fiscal year. Petroleum became the leading export item in terms of value, surpassing coffee and cocoa exports. Mineral exports as a whole increased eightfold in value, mainly because of oil sales. Oil exports also caused a reduction in the trade deficit by nearly one-third, and the Government expected its 1980-81 budget to be balanced at $1.17 billion. The Port of Douala accounted for about 8 million tons of cargo, or 93% of total maritime traffic for Cameroon. Expansion plans for the port call for an initial increase to 5 million tons, and a cargo handling capacity of 7.5 million tons in 1985 and 10 million tons by 1990. The Port of Victoria will gain importance with the startup of an oil refinery. The country's third seaport at Kribi was used solely for timber shipments, and capacity at the Port was to triple by 1981. The Government operated its own shipping line with six oceangoing freighters. France was the dominant trading partner, accounting for 25%

Jan 1, 1982

By R. J. Traube

The purpose of the Inherently Safe Mining System (ISMS) project is to develop continuous and conventional coal mining equipment and systems which will reduce the incidence of fatal and nonfatal accidents in the working sections of underground bituminous coal mines by application of existing technology. This 3-year program, initiated on 18 June 1971, is being conducted in three phases: ? PHASE I (8 months) Systems Analysis Concept Design Planning ? PHASE 11 (16 months) Design Procurement Manufacture Preliminary Testing ? PHASE III (12 months) Underground Coal Production Demonstration.

Jan 1, 1972

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau's program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

By Mark S. Stagg

Blast-induced ground vibrations from surface coal mine, quarry, and construction blasting were measured and analyzed for frequency content and duration characteristics. Eighteen commercially available ground vibration measurement systems were evaluated in the field and laboratory for linearity, accuracy, and crosstalk. Buried, surface, and sandbagged transducer placement methods were compared, along with peak and vector-sum measurements. The recommended minimum frequency ranges for ground vibration instrumentation are 2 to 150 Hz for coal mine and quarry blasting, and 5 to 200 Hz for construction and excavation blasting. When higher or lower frequency vibrations are possible, as in construction blasting or for a quarry shot close to a residence, care should be taken to insure proper choices of instrumentation and vibration criteria. Several instruments operating in these ranges are available, and all but one of the seismographs tested fell within ±3-dB accuracy limits (+41 pct, -29 pct). Waveform recordings of all three ground vibration components are recommended as the peak amplitude and frequency may vary among the three. Peak or vector-sum readings are adequate if only amplitude levels are desired. The soil density matched box should be anchored or buried, particularly for high-frequency, high-amplitude construction blasting.

Jan 1, 1980

The investigation summarized in this report addressed two primary issues: the determination and use of correction factors, and the development of guidelines for velocity measurement site selection. Other ancillary issues which were addressed include a comparison of measurement methods and devices, aircourse cross-sectional area measurement, and characteristics of mine airways. An exhaustive literature search and analysis was performed; extensive in-mine experiments were conducted; a quantitative analysis of the data was used to develop correction factor tables and site selection guidelines. The reported results of other researchers who have examined the correction factors and site selection criteria, were analyzed in light of the results of this study. The measurement devices included in the experimental phase were: vane anemometer, vortex shedding anemometer, a prototype thermoanemometer, smoke tube, and, oil of wintergreen. The measurement methods include single-point centerline, timed¬-point traverse, continuous traverse for the anemometers, and various distances and cloud positions for the smoke tube and oil of wintergreen devices.

Jan 1, 1983

By Travis Q. Lyday

During 1983, Ecuador's gross domestic product (GDP) decreased by a reported 3.3% in real terms, the second consecutive decline in the economy after more than a decade of growth generated mainly by petroleum export revenues. The slowdown was due, in part, to the effects of the world recession, lower foreign demand for oil, depressed world oil prices, and reduced demand and prices for Ecuador's traditional agricultural exports. Inflation accelerated to an estimated 55% annual rate. The sucre was devalued in March, for the second time in less than a 12-month period, by 27% after remaining unchanged during the previous decade. In addition, continuous adjustments were made every weekday, effectively devaluing the sucre another 30% by yearend. Ecuador's production of crude petroleum increased almost 12% in 1983 compared with that of 1982. Average daily production was 237,100 barrels per day (bbl/d), up from 211,300 bbl/d in 1982.

Jan 1, 1985

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Martin J. Gavin

During the recent study of lubricating oils carried on in the San Francisco laboratory of the United States Bureau of Mines, it became desirable to distill the oils used in the experimental work at pressures as low as 10 millimeters (mercury column) absolute. In the effort to Overcome difficulties and eliminate sources of error, certain changes were made in the apparatus for vacuum distillation used by the Bureau of Mines for crude petroleum.4 These changes were described in R.I. 2819, issued in July, 1927. Subsequent to the publication of R.I. 2819 several other changes have been made, and the present form of the apparatus for vacuum distillation of lubricating oils is described in this revision of R.I. 2819. These changes were found to give more accurate checks on duplicate distillations. The major part of the credit for the laboratory work which developed the changes in the apparatus and method revised herein is due to Boyd Guthrie, assistant petroleum chemist, and R. V. Higgins, junior chemist, o the San Francisco laboratory, United States Bureau of Mines. DESCRIPTION OF APPARATUS The distilling flask employed is essentially the Hempel flask as used by the United States Bureau of Mines for the analytical distillation of petroleum.5 he complete apparatus is shown in Figure 1. The fractionating column and exposed portion of the flask is wrapped with 4 inch asbestos rope and then surrounded by a cylindrical hood of 1/8 inch pliable asbestos sheet with a narrow air space between the wrapping and the cylindrical hood. This was found necessary to prevent any radiation or convection heat losses from the column, and resulted in obtaining a more even and constant fractionation by eliminating any dephlegmating action caused by temperature changes around the column.

Jan 1, 1930

By Lon A. Williams

This appendix contains drawing lists and drawings of components and assemblies designed for the prototype portable and machine mounted lighting systems per Tasks II & IV of Contract No. H0220065.

Jan 1, 1976

By L. B. Phelps

A method is presented for the burial of potentially toxic spoil in high density zones or packages within spoil piles. Such burial could reduce the outflow of pollutants and thus minimize contamination of groundwater flows. Laboratory model studies using ammonium bromide tracer were performed to quantify the expected outflow mixing that could be achieved through package construction in spoils. Field drilling and geophysical density logging of spoils was carried out at three sites in Pennsylvania and Ohio to obtain a range of field spoil bulk density measurements and spoil samples. These data are analyzed to determine the relationships between spoil density and the controlling factors of lithology, depth, age, particle size distribution and mining method. A separate series of spoil permeability tests were performed in the laboratory to investigate the relationship between permeability and its related parameters. Research results are applied to the toxic package method to suggest guidelines for pack-age size, shape, density and placement for future field prototype development.

Jan 1, 1981

By B. G. H. Thomas, W. P. Yant, A. C. Fieldner, R. R. Sayers, W. J. McConnell

"One of the outstanding problems confronting automotive engineers in attempting to construct motors of greater economy is that of eliminating the ""knock"" from the operation of the engine. Recent investigations of this detonation or knock in internal-combustion engines, especially of the high-compression type, have demonstrated that it can be eliminated or reduced by decreasing the reaction velocity of combustion by adding small quantities of certain compounds to the gasoline, This makes it possible to use engines of a higher compression ratio, thereby greatly increasing the mileage per gallon of gasoline consumed. The savings in fuel reserves from increasing the proportion of crude oil marketable as motor fuel and in permitting the designing of more efficient engines are obvious.Ethyl gasoline, one of the widely used anti-knock fuels, is ordinary motor gasoline to which has been added 3 c.c. of tetraethyl lead and 2 c.c. of a halogen carrier, as ethylene dibromide or trichiorethylene, or approximately 0.06 per cent of the lead compound and 0.04 per cent of ethylene dibromide by volume. Ethyl gasoline should not be confused with ethyl fluid, which is a mixture of concentrated tetraethyl lead and ethylene dibromide in the prowler proportions for mixing with gasoline, but is not a motor fuel and is not sold to the public. Also tetraethyl lead is not a motor fuel, and likewise is act sold to the public."

Dec 1, 1924