Search Documents

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Monongalia County, W. Va. It is one of a Bureau of Mines series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. Over 9.5 million tons of coal was produced in Monongalia County in 1957, of which more than 7 million tons was cleaned mechanically in 8 cleaning plants. On January I, 1954 the Bureau of Mines estimated that 1,576 million tons of recoverable coal remained in the county in beds 28 inches or more thick.

Jan 1, 1960

By C. A. Komar

The Bureau of Mines conducted oil-displacement tests in the laboratory with three water-in-oil and five oil-in-water emulsions that were created with ultrasonic energy at a frequency of 20 kHz and an acoustic intensity of approximately 100 watts per cm2. Emulsions of either crude oil or kerosine, brine, and 112 to 2 percent emulsifier were formed during 30 seconds of acoustic irradiation. Results indicate that ultrasonic energy induces greater and more uniform dispersion of one liquid in another in the presence of small amounts of chemi¬cal emulsifiers. When the emulsions were injected as a buffer slug before waterflooding, recovery of the oil-in-place was 8 to 22 percent greater than with conventional waterflooding in the test specimens, regardless of the con¬tinuous phase (oil or brine). The emulsions do not appear to be applicable to the Appalachian area; however, because the oilfields are too "tight," the clays in the formation remove the emulsifier from the displacing fluid, and not enough additional oil is produced, compared with recovery using conventional waterflooding, to warrant the increased operating costs.

Jan 1, 1969

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By W. W. Adams

The United States Bureau of Mines, in cooperation with the National Send and Gravel Association conducted a safety contest in 1929 Among producers of sand and gravel. Only 26 plants were enrolled, as the contest was late getting under way. It is hoped that a ranch larger number of plants will be represented in the safety competition of 1930. Two trophies, both of which were provided by Rock Products magazine, were awarded at the end of the contest; one trophy was given for the best safety record among plants working 100,000 or mare man-hours during the year and the other for the beat record among plants working less than 100,000 man-hours. The trophies were presented to representatives of the winning, companies on January 29, 1930, at the annual convention of the National Sand and Gravel Association at Memphis, Tenn.

Jan 1, 1930

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By Fred Leighton

The Bureau of Mines has developed rock noise source location techniques that may be used to obtain precise and practical source locations from micro-seismic field data. These techniques enable one to monitor all or any part of a rock structure and map progressive stress buildup or rock movement. Thus, the microseismic method of determining instability in rock structures is becoming an invaluable engineering tool for the mining or civil engineer engaged in rock excavation and construction.

Jan 1, 1970

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

By T. J. Ballard

Chromite deposits in the vicinity of Louise, Troup County, Ga., were studied y the Bureau of Mines from September 1, 1942, to March, 15, 1943. They are about three-fourths of a mile southeast of Louise and 8 miles northeast of La Grange, Troup County, Ga. The existence of chromite deposits in that area has been known for more than 75 years, but no active prospecting was done until World War I. Prospecting continued intermittently' until 1928. The Bureau became interested in the deposits in connection with its strategic minerals investigations during World War II. The chromite in these deposits occurs as grains ranging from "pin-head" size to 3/8-inch and occasionally 1 inch. Some of the material is magnetic, indicating the presence of magnetite. Of the 300 samples taken during the course of the project, 266 were analyzed. Tables showing the analyses accompany this report.

Jan 1, 1948

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By William R. Vogel

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral- material production or consumption.

Jan 1, 1988

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By William N. Patterson

This report describes the design and testing of an improved quiet hard rock percussion drill. The improved drill incorporates a tappetless design with independent rotation in a hand held drill weighing 50 lbm. Laboratory and field testing in three mines were conducted. The testing showed improved drilling performance with no increase in measured noise levels over the fist design.

Jan 1, 1985

By G. P. Houston

This is the final, report submitted for the Contract No. H0220002 with the U. S. Bureau of Mines for the design and development of a Permissible Automatic Data Acquisition System (PADAS) to measure and record roof stresses in underground mines Basically the PADAS is a portable, battery powered, 24-channel data acquisition system designed for safe unattended operation of up to 30 days duration in explosive environments. The unit will accommodate twenty-four pressure transducers or eight borehole deformation gages (or any combination) at distances up to 300 feet from the PADAS to measure pressures up to 10, 000 psig. All 24 channels as a selected group are scanned sequentially at one of several selectable rates.

Jan 1, 1973