Search Documents

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

By Harold H. Fukubayashi

The effect of various zinc electrowinning solution impurities on the surface morphology of deposited zinc was investigated. Impurities studied included Al, Ag, Cd, Co, Cr, Cu, Ge, Mn, Ni, Sb, Sn, Ti, Pb02, PbSO4, and HC1. Also, the effect of animal glue, gum arabic, and Na2SiO3 additives on the deposited zinc surface structure was studied. Results were compared with deposits from a pure electrolyte consisting of H2SO4 and Zn+2, 200 and 65 gpl, respectively. Zinc was deposited on a Al cathode, 99.9 pct pure, using Pt anodes. Time, temperature, current density, and impurity concentrations were con¬troller The bulk of the tests were conducted at 40° C and 75 A/ft2 (82 mA/cm2). A scanning electron microscope (SEM) was used to examine the surface morphology. X ray diffraction techniques were used to determine crystal orientation and nondispersive X-ray spectrometer analyses were employed in an attempt to locate impurity concentrations on the zinc deposit when pitting or re-solution occurred. The impurities were categorized by their effect on current efficiency, morphology, and apparent mechanism of H2 evolution from the cathode.

Jan 1, 1974

By Francis X. Cannaday

The purpose of this investigation was to find whether the moduli of elasticity obtained were the same for the following methods : ( 1 ) Deformation of a borehole in a prism subjected to uniaxial stress ; ( 2 ) deflection of a thin beam of uniform cross section uniformly loaded ; ( 3 ) sonic - pulse velocity measurements , and ( 4 ) strain measurements on a prism under uniaxial stress . The rock tested was chosen for its good elastic behavior and relatively good homogeneity and elastic isotropism . The same rock was used for all methods . Results indicate that for given environmental and stress conditions the moduli obtained by each of the four methods check one another within the limits of experimental error and that the differences introduced which are characteristic for each method are smaller than physical variations within the rock tested .

Jan 1, 1964

By Jr. Holmes

The Bureau of Mines drilled and sampled the more important magnesite deposits in the Currant Creek Mining District, White Pine County, Nev. The properties of the Ala-Mar Magnesium Co., Inc., and the Nevada Magnesite Co. were examined in August 1942 by D. W. Butner, engineer of the Bureau of Mines, to determine the advisability of investigating the deposits under the strategic minerals program. Development involving diamond drilling, trenching, and sampling was started September 1, 1942, and was completed in the latter part of November 1942. The deposits are on unsurveyed public land in T. 12N., B. 59 E., M.D.B.&M., in an area of high relief ranging from 7,300 to 8,100 feet in altitude. Both properties are situated northwest of the Tonopah-Ely Highway, U.S. Highway 6, from which a dirt road extends about 4.6 miles northwesterly, about 35 miles southwest of Ely, to the Ala-Mar property, and another dirt road extends about 10 miles westerly, about 26 miles southwest of Ely, to the Nevada Magnesite property. The magnesite occurs as irregular nodules, veins, and lenses in a bedded calcareous tuff formation, which overlies a group of volcanic rocks, and which is capped by remnants of rhyolite flows.

Jan 1, 1950

By Felix duBreuil

The present sampling procedure for evaluating the rock dusting conditions in a coal mine is time consuming. This study considers means by which this procedure could be simplified. Surveys were conducted in six coal mines in Pennsylvania to determine the in¬combustible content of the deposited dust. Some 2,000 samples were analyzed and statistically evaluated. It is suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error.

Jan 1, 1972

By D. W. Dareing

Multiple branch wellbores and horizontal holes, when applied to deep lying ore bodies, have the potential of significantly reducing well costs by reducing total footage drilled per acre of well pattern. In addition, horizontal holes may increase sweep efficiency. Well completion is a major problem. They must be cased to contain leaching solutions within the underground portion of the production loop. Several drilling and completion concepts are given and evaluated in the report. Our evaluation shows that there is economic incentive to further develop these concepts for field application to ore bodies 1,500 feet. Multiple branch concepts are the most attractive. They can reduce well costs by as much as 30° when applied to 2,000 feet ore body depths (44%, at 5,000 feet) and can accommodate a lamer pump than conventional vertical wells. We recommend this concept be developed further to accommodate either dual or triple branches.

Jan 1, 1980

By Lloyd A. Morley

Research performed on computer modeling of mine power systems under USBM Grant G0155003 1S described. The work was performed at the Pennsylvania State University from 5 November 1975 through 4 November 1976. Results presented are interim in nature, and future research is planned to integrate the simulations which have been developed. The thrust of this research has been divided into three main areas. 1. Modification of a previously developed model (Mine Power System Simulation or MPSS) to include interactive operation and the use of default (average) load data. 2. Development of a dynamic simulation of interdependent mine power system induction motors. 3. Development of an approach to modeling of motor shaft loading of induction machines for mining operations. During the course of the current year's research, significant results have been achieved in all areas. Construction of an interactive MPSS model has been completed and checked. This simulation was written in APL code and is fully interactive. In addition, default data representing 158 different pieces of mining equipment has been developed for use with the interactive model. Additional work described includes the construction of a dynamic simulation of interdependent continuous miner induction motors and the development of an approach fo: motor shaft load torque computation from experimental data.

Jan 1, 1976

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By Henry P. Chandler

TONNAGE of natural abrasives sold or used in the United States in 1959 increased 12 percent. Artificial abrasives produced in the United States and Canada jumped 24 percent. Imports, exports, and reexports of abrasive materials also showed gains. Sales of grinding wheels were up 33 percent and coated abrasives 17 percent. FOREIGN TRADE Imports of abrasive materials totaled $91 million, an increase of nearly 51 percent over 1958. Chief commodities contributing to [ ]

Jan 1, 1960

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By N. A. C. Smith

[The beau of Mines made its first survey of motor gasolines sold throughout the United States in 1915, a second in 1917, and a third in April. 1919. These surveys shored that motor gasoline had become notably less volatile during each two-year interval. In order to ascertain whether this change was continuing, it was planned to institute semi-annual surveys, the first of which teas made in January, 1920. Contrary to expectations based on the previous surveys, the average volatility of the gasoline tested at this time was practically identical with that of the average volatility of the gasoline from the same districts in 1919. The next survey, made in July, 1920, showed a very marked decrease in volatility but as it has long been recognized that the volatility of motor gasoline manufactured for sale during the summer months is loss tan that of gasoline made and sold during the winter, part at least of the change was attributed to this factor. The average boiling point of the samples collected in the present survey is 263 degrees Fahrenheit, as compared with 264 a year ago. This shows that the average gasoline marketed at the present time is fully as volatile as that marketed a year ago. There has been, however, a noticeable change in the character of the product: the initial boiling point and 20 per cant point are lower than a year ago, whereas the 90 per cent and end-points are higher, which indicates a greater proportion of gasolines made by blending casing-head, or natural gas-gasoline, and naphtha.]

Jan 1, 1921

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A series of four coal combustion experiments was conducted at the National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Laboratory (PRL) in the Safety Research Coal Mine (SRCM) to evaluate the response of fire sensors to a small 0.61 m square smoldering coal fire which transitions to flaming combustion in the presence of diesel emissions. An optical path smoke sensor alarmed earlier than a point type diffusion mode ionization smoke sensor which alarmed prior to a CO alert value of 5 PPM above ambient. The presence of steady state diesel emissions resulted in a decrease in the optical smoke sensor analog output voltage signal by less than 1.4 pct for the three coal fire experiments in which a diesel engine was operating, whereas the ionization smoke sensor output decreased between 10.8 and 26.7 pct after the initial surge of the diesel engine. A commercial diesel discriminating fire sensor did not alarm for a fire in the one experiment for which it was used. The results of the experiments demonstrated that an optical path smoke sensor might be used to detect a coal fire under the experimental conditions considered of starting a diesel engine followed by a slowly developing coal fire.

By John M. Devine

Hydrogen sulphide associated with natural gas was noted as early as 1892, at Point Albino, Canada.4 The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence urea by no means common. However, in recent years, with the development of the producing zones of west Texas and the Texas Panhandle, the production of "sour" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor--frequently a major problem--in the drilling and operation of many wells in those areas. The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is mane of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen sulphide. From the standpoint of safety end health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. 5 Likewise, the problem of hydrogen-sulphide

Jan 1, 1931

By R. G. Warncke, D. Harrington

"INTRODUCTION The use of black blasting powder as an explosive in coal mines has long been recognized as hazardous and has been responsible for many of the worst disasters in American coal mines. One of the most pressing of the numerous problems confronting the Bureau of Mines, upon its creation in 1910 was to determine methods that would lessen the hazards created by the use of explosives in coal mines. The Bureau continued the study begun by the Technologic Branch of the Geological Survey as to the nature of explosives and made numerous tests to determine types of explosives suitable for blasting in coal mines. The Bureau has tested and approved hundreds of types of explosives and has disseminated information on methods and conditions for use underground to make them permissible as to safety. The Bureau of Mines has encouraged the use of permissible explosives for coal-mine blasting, and its experts both in the laboratory and in the field believe that the use of black blasting powder in any form (granular or pellet) is hazardous in any underground coal mine. Despite the information published at various times and innumerous ways and the general knowledge of the hazards that the use of black blasting powder in any form creates in the blasting of coal, the coal mines in the United States, during 1947 used approximately 34 million pounds of black blasting powder (granular or pellet), or approximately 11.8 percent of the total quantity of explosives used by the coal-mining industry.Many coal mines of the United States, for various and sundry reasons, probably will continue the use of black blasting powder, and this circular has been written for the benefit of such users, not that any suggested method or methods will make the use of this explosive safe, but it has been found that methods and conditions of use of black blasting powder can be improved so as to lessen, though not eliminate, the hazards created by its use."

Mar 1, 1949

By R. J. Leary

This investigation was conducted to determine the effects of various rare-earth metal addition practices upon the macrostructure and the pattern of sulfur distribution in steel ingots. Heats of plain carbon steel were melted in a 1-ton, basic electric-arc furnace. Melts were treated with mixtures of rare-earth silicides, aluminum, and cryolite either in the furnace before tap or in the ladle after tap to determine the effects of this form of rare-earth treatment upon ingot macrostructure. Steels thus treated with rare earths in the furnace were characteristically free of the gross subsurface nonmetallics which typically result from conventional rare-earth treatments. Steel treated in the ladle showed only a few such nonmetallics, and practical techniques were developed for eliminating most of these. Results showed that furnace deoxidation was controlled by the concentration ratio of rare earths: aluminum. During casting, deoxidation was controlled by the concentration of rare earths. Oxygen contents equivalent to vacuum ladle degassing resulted from air-melt furnace treatments with the rare-earth mixtures described. Rare earths in steel inhibited the onset of equiaxed grain formation during ingot freezing, and also virtually prevented interdendritic segregation of sulfides.

Jan 1, 1968

By J. Robert Wells

The Bureau of Mines has developed a spectrochemical procedure for determining 19 impurity elements in high-purity titanium metal, titanium oxides, and titanium halides in which all samples are converted to titanium dioxide. Determination of these impurities was studied in the general concentration range of 0 to 1,000 p.p.m., but different determination limits were found for the various elements. The procedure is quantitative for 18 elements but semi-quantitative3 for beryllium and has an overall relative standard deviation of 15.8 percent. Two mixtures were used, one composed of graphite and lithium carbonate plus gallium oxide and the other of graphite and lithium carbonate plus germanium dioxide. Each mixture was blended mechanically with an equal weight of titanium dioxide. Lithium carbonate served as buffer-diluent. Gallium was the internal standard for 1 impurity element, germanium for 7, and titanium for the remaining 11.

Jan 1, 1962

By H. B. Humphrey, F. E. Cash

The Southern Appalachian coal field extends southward across Tennessee in a belt about 50 miles wide between the eastern and middle sections of the State. The earliest record of the production of coal in Tennessee is for 1840, and the first inspection laws were passed in 1881. In 1887, a second act of the legislature created the office of Chief Inspector, but little was done until 1891 when a new act was passed giving to the Department of Mines added duties and powers. Since that time, except for the years 1915 to 1918, com¬ prehensive annual reports have been published. Data for the tables given in this paper are taken from these annual reports, from those of the Southern Appalachian Coal Operators' Association, and from the publications of the United States Bureau of Mines, which has main¬ tained a station at Jellico, Tenn., since 1911. Complete figures for 1930 are not available yet and they are not included in the averages. The State Department of Mines, the operating companies, and the United States Bureau of Mines cooperate in accident-prevention work. It is the purpose of this report to present in uniform tables the available statistics in regard to fatal accidents in Tennessee and in the coal mines of the United States, in order that the progress in mine safety in Tennessee may be compared with that of the country as a whole, and the present period may be compared with various periods of the past, to indicate the main points of attack in the reduction of accidents.

Sep 1, 1931

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952