Search Documents

By Joseph J. Wallace

1. The Pittsburgh is the most important bed in Washington County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 4,181 million short tons as of January 1, 1954. Of this total, 4,132 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By Frederick Bloetscher

An improved parachute-type stopping for changing the course of mine ventilation air during mine emergencies has been developed by Goodyear Aerospace Corporation for The Bureau of Mines. The stopping can be quickly deployed by one man from a single attachment point and provides excellent stopping performance with the flow in the design direction. Adding pin and foam attachments between its skirt and the passage-way surfaces improves its performance with flow in the design direction and maintains the stopping with zero or reverse air flows. Stopping performance results for a range of airway sizes including 7.5 X 10 ft simulated airway with pressure differentials of up to 3.0 inches of water are presented. Predicted performance values for this stopping design for larger passageways are also presented.

Jan 1, 1977

By Larry Gsellman

This report presents the results of a benefit/cost analysis of the Bureau of Mines' Coal Extraction RCD Program for the period FY 1977 through FY 1982. The analysis is an update of the analysis performed on the Coal Extraction R&D Program for EY 1975 - FY 1980 and presented in a MITRE report, MTR-7225, published in May 1975. Major changes included: new production scenarios and an update of R&D cost estimates.

Jan 1, 1977

The Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining (hereafter referred to as the Panel or the TSP) was established by Section 11 of the Mine Improvement and New Emergency Response Act of 2006 (MINER Act). The Panel was charged with providing “independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant properties of belt materials in underground coal mining.” The TSP was impaneled by the Honorable Elaine L. Chao and commenced its work on January 9, 2007. At this first meeting, Mr. Richard E. Stickler, Assistant Secretary of Labor for Mine Safety and Health, asked the Panel to report on many issues including how recent technological advances could be applied to atmospheric monitoring systems, point-type heat sensors, current state of fire-resistant vs. fireproof belt materials, and belt fire suppression systems to improve miner safety. In addition, Mr. Stickler asked the Panel to review belt air velocity limitations. The Panel members attended 12 days of public meetings over a nine-month period. Three of the public meetings were scheduled for the Panel to hear from technical experts and those persons or organizations interested in providing input. The meetings were held in Coraopolis, Pennsylvania with emphasis on belt fires, belt maintenance, belt flammability and toxicity, ventilation, and escape issues; in Salt Lake City with emphasis on ground control and convergence issues; and in Birmingham with emphasis on fire detection, sensors and atmospheric monitoring systems. National Institute for Occupational Safety and Health (NIOSH) researchers, Mine Safety and Health Administration (MSHA) personnel, representatives of the major belt conveyor manufacturers and a representative of the National Mining Association provided discussions at the Coraopolis meeting. In Salt Lake City, Utah, MSHA district managers and ventilation specialists, a member of the Aracoma Mine No. 1 investigation team, a representative of the Bureau of Land Management, and industry and consulting representatives of the Utah Mining Association and the Colorado Mining Association made presentations. In Birmingham, Alabama, atmospheric monitoring system representatives, NIOSH researchers, representatives of coal mining companies, and UMWA workers from two Alabama mining companies made presentations. In addition, a staff member of The Center for Regulatory Effectiveness also presented comments to the Panel. In conjunction with the meetings in Salt Lake City and Birmingham, three-member subcommittees of the Technical Study Panel made field visits to the Skyline Mine, the Aberdeen Mine, and the Jim Walter Resources Mine No. 4. The mine visits were scheduled to see first-hand the mining conditions under which belt air was being utilized as an additional source of intake air for working sections.

By L. C. Brichta

The Tri-State zinc-lead catalog, compilation of which was initiated by the Bureau of Mines in August 1949, is designed to provide a continuing record of avail-able drill-hole logs and maps of mine developments in the zinc-lead district in southwestern Missouri, southeastern Kansas, and northeastern Oklahoma. The maps and data thus preserved constitute a reservoir of factual information readily available to individuals and firms interested in planning mineral explorations, to Government agencies for formulating estimates or ore reserves, and to the mining industry in the district for general uses. The areas to be included in the catalog embrace the explored and mined tracts within 760,000 acres of the more active western part of the district. The consensus among local mine operators, geologists, and mining engineers is that over 100,000 boles, costing more than $30,000,000, have been drilled in the district. Records of some of the early drilling and mine developments are destroyed or lost, but the Bureau of Mines has copies of about 47,500 drill-hole logs and is accumulating and recording on microfilm those that are currently available. As of May 1, 1954, the logs of approximately 28,000 drill holes had been microfilmed and are available for inspection at the Bureau of Mines office, Joplin, Mo.

Jan 1, 1955

By A. Gene Collins

The Bureau of Mines undertook research to determine the bromide and iodide content of Mississippi and Alabama oilfield waters of the Tertiary and Cretaceous Period to determine genetic relationships of the ions, to determine their origin, and to determine their genetic relation to petroleum. The 280 samples were analyzed after a pretreatment to remove interferences. The iodide was oxidized to iodate and was titrated with thiosulfate. The bromide was oxidized to bromate and was determined iodometrically. A computer was used to calculate the correlation coefficients of iodide to bromide and to other ions. The other ions are sodium plus potassium, calcium, magnesium, chloride, bicarbonate, and sulfate. The mineral content of the samples ranged from 52 to 1,760 mg/l for bromide and from 2 to 65 mg/l for iodide. The mean bromide-to-chloride and iodide-to-chloride ratios were 0.0065 and 0.0002. The correlation coefficient matrix and linear plots indicated a definite bromide-to-calcium relationship for the brines investigated.

Jan 1, 1967

By G. G. Morgis

A reasonably clear and broad definition of occupational disease as originated by the Supreme Court of Ohio is: "A disease contracted in the usual and ordinary course of events which from the common experience of humanity is known to be incident to a particular employment." An ailment does not become an occupational disease simply because it is contracted on the employer's premises. It must be one that is commonly regarded as natural to, inherent in, and concomitant of the work in question. The important distinction between accidental-traumatic injuries and occupational-disease injuries is that accidents occur at specific times, ordinarily are discovered readily, and usually leave no question as to the particular employer it whose development the accident occurred. On the other hand, occupational diseases may develop slowly, unknown to the employer and employee until disability occurs, and the injuries sustained are continuing disabilities over an extended period of time and may be incurred while the employee is working for one of several employers.

Jan 1, 1952

By James J. Dawd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the ninth of a series of reports giving results of studies by counties under part (1) of the investigation. (See Appendix.) This report covers Raleigh County, W. Va., which comprises parts of Bald Knob, Eccles, Beckley, Meadow Creek, Mullens, Flattop, and Big Bend quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, location of drill holes, bed and total coal thickness, and outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas. areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By G. W. Jones

The Bureau of Mines has advocated the use of stenches as warning agents in metal mines and in gas-distribution systems since 1920 A considerable amount of research has been conducted on ethyl mercaptan and other compounds to determine their effectiveness when used for this purpose.4/5/6/7/8/9/10/11/12/13/ Miners are warned of danger by a stench injected, in measured quantity, into a compressed-air line through which it is rapidly carried to the working faces, where it escapes from the compressed-air equipment and imparts a characteristic odor to the air. This method is not applicable to mines where only a limited number of com-pressed-air lines are used, as for example, many coal mines; the ventilation currents available in these mines may be too slow for warning purposes.14/

Jan 1, 1954

By J. C. Duchon

The use of extended workdays or compressed workweeks (regular shift lengths exceeding 8 h) is attracting growing interest in many industries using continuous operations. While extended workdays promise increased worker satisfaction due to more days off, including weekends and holidays, there are legitimate concerns about the potential effects on the health and safety of such a schedule. The U.S. Bureau of Mines (USBM) conducted a study at a Canadian underground copper, lead, and zinc mining operation that was designed to study the safety and performance implications of extended workdays. Measures were taken before and after a change from the old 8-h continuous schedule to the new 12-h continuous schedule, including behavioral performance measures to analyze perceptual-motor changes, continuous heart-rate monitoring and aerobic capacity to measure physical fatigue, a variety of self-report questionnaires to measure perceived adaption and satisfaction with the new schedule, and pulmonary-respiratory measures to examine air contaminant exposure. Based upon the overall acceptance of the new schedule by the workers and lack of change in fatigue-sensitive behavioral and physiological performance measures, this study recommends that the mine retain the 12-h schedule. However, certain precautionary measures are suggested to insure the safety of the workers.

Jan 1, 2010

By J. B. Vander Sande, L. C. Rainey, P. Bolsaitis, B. Dirsa

"The structure and composition of silica-rich particles recovered by lavage from the lungs of three active miners with different medical histories were studied using high-resolution electron microscopy and chemical microanalysis. The results arc compared to the similarly determined structure and composition of respirable-size mineral particles obtained from roof-bolter dust-box samples from two coal mines of widely different bulk quartz concentrations. The results show that the lungs of the miners contain silica-based particles with structures not found in the mine samples. Also, the particle structures and compositions found in the macrophages were different in each of the miners. The rau.lu suggest the possibility that intracellular processes may affect the susceptibility of individuals to silica-induced pneumoconiosis. The cytotoxic and fibrogenic potentials of mine dusts result from the activity of their individual components. Whether this effect is additive or even mass (i.e., dose) related is questionable and has been the subject of many investigations. Particle size and size distribution of various constituent minerals, the surface structure and properties of individual particles, and the self-cleaning capability of the lung (i.e., the capacity of the macrophage system) may, among other variables, affect the pathogenic changes induced by dusts lodged inside lungs. Extensive epidemiological investigations conducted on miners from different coalmining districts, where equivalent dust exposures have been shown to result in vastly different frequencies of lung disease incidence, also confirm this hypothesis (1) In a recent study, Ferrer et al. (2) used energy-dispersive X-ray analysis (EDXA) to investigate the inorganic element content in pleura and lung in reference, silica exposed non-pneumoconiosis, and silicotic populations. Constant depositions of silicon and calcium were detected in visceral pleura, parietal pleura, and lung of the refence group and in visceral pleura and lung of the exposed non-pneumoconiosis and silicotic groups. Comparison of the silicon content in pleura between silicotic and exposed non-pneumoconiosis subjects showed a nonsignificant probability of difference, whereas there were no differences with respect to the silicon content in lungs."

Dec 1, 1995

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978

By Joseph J. Wallace

1. The investigation shows that nine coal beds have been mined in Harlan County, of which the Harlan and Upper Elkhorn No, 3 are the most important from the standpoint of present production. Of less importance are the Hindman, Flag, Haddix, Wax, Fire Clay, Armburgy, and Upper Elkhorn No. 2. The Harlan, Upper Elkhorn No. 3, and Upper Elkhorn No. 2 beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 2,138 million short tons as of January I, 1932. Of this total, 1,956 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study, Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By C. P. Mishra

The Bureau of Mines investigated the availability of mercury from 22 deposits in market economy countries. The 15 significant deposits evaluated have demonstrated resources of approximately 25 million metric tons of ore containing 5.3 million flasks of mercury and account for more than 85 pct of the demonstrated resources for market economy countries. Using data gathered as part of its Minerals Availability Program, the Bureau determined the mercury production potential of each deposit. At a January 1984 mercury market price of $300 per flask, the deposits evaluated could economically produce an estimated 2.5 million flasks of mercury from six mines operating at the time of this study; no mercury is available at this price from nonproducing operations. At $600 per flask, approximately 4.5 million flasks of mercury are available. For production costs up to $300 per flask, operating mines could supply mercury at the current production rate of 114,000 flasks per year until 1988, when the amount of mercury available from these deposits would decrease. This decline could be offset by the development of resources currently reported at the identified level (17 million flasks) at much higher production costs.

Jan 1, 1985

By Parry. V. F., W. S. Landers

"INTRODUCTION Approximately 1,250,000 tons of 2-1/2-inch and 1-1/2-inch slack, representing over half of the output from 40 to 50 mines, is produced in the Denver region each year. Part of this slack is made by crushing lump, and some of it is rescreened to make pea and modified pea sizes measuring 1-1/2 inches by 2-1/2 inches and 3/4-inch by 1-1/2 inches, round-hole. Modified pea is popular as domestic stoker fuel. Approximately 900,000 tons of slack 0 by 2-1/2 inches, 0 by 1-1/ 2 inches, and 0 by 3/4-inch in size are consumed by industrial plants, the principal consumers being a large power plant and the beet-sugar industry. The power plant uses annually 250,000 to 275,000 tons of pulverized fuel and can pulverize slack of any size, while the sugar factories consume about the same quantity of coal in stokers. The sugar factories store about 110,000 tons of 2-1/2-inch slack under water from January to October, and burn the remainder of their consumption directly during the campaign season from October to December. For this purpose, sugar-factory power plants can use any size of slack, which is recrushed to pass a 3/4- or 1/2-inch screen before burning on chain-grate stokers. About one-third of the 2-1/ 2- inch slack produced in the field is used in smaller industrial plants that employ stokers.Certain factors affect the utilization of 2-1/2-inch slack in the Denver region. The increasing production of hydroelectric power has reduced the consumption of coal at power plants slightly. If more hydropower is generated, the trend of consumption of slack might be downward, unless industrial activity offsets this greater output. Rapid increase in number of domestic stokers during recent years has necessitated preparation of greater quantities of stoker coal, with the result that more lump is crushed, and preparation facilities are changed. At present about 19 percent of the coal produced is crushed to meet the constant demand for industrial fuel as well as the increasing but variable demand for the small domestic stoker sizes. The quantity crushed has increased 12 percent during the last 6 years. These factors are shifting constantly. The trend toward the use of clean and smaller sizes for domestic stokers gives a slack having a larger proportion of fines. In future, even greater quantities of small stoker coal probably will be prepared, and the resulting greater quantities of small slack will have to be used for industrial purposes."

Aug 1, 1942

By Phillip N. Yasnowsky

This Bureau of Mines report summarizes State severance taxes imposed on minerals and mineral fuels, provides a hypothetical example of how a State severance tax affects selected components of a firm's income statement, and uses the Bureau's Minerals Availability System (MAS) to estimate the effect of assumed changes in State severance tax rates on copper recovery cost at given levels of potential copper availability. A reduction of the rates to zero or a doubling of them results in changes in costs that are of the same order of magnitude as the cost of transporting copper to the United States from major foreign producing countries.

Jan 1, 1982

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976