Search Documents

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By George T. Krempasky

This report is one of a series of Bureau of Mines Information Circulars dealing with mining methods and costs throughout the United States. It describes drifting, crosscutting, and raising operations at several mines in the Coeur d'Alene mining district, Shoshone County, Idaho. Ore bodies in the Coeur d'Alene district are generally in steeply dipping tabular ore zones, are irregular in shape, erratic in occurrence, and have been extensively mined along the strike and down dip. Because of the extended attitude of the deposits a great deal of development work is required. Drifting, crosscutting, and raising methods are described in this report. Shaft sinking is the subject of another report in the same series.

Jan 1, 1960

By W. F. Faragher, W. A. HORNE

Previous interrogation of German scientific personnel by numerous in- vestigators and the examination of evacuated documents indicated that fur- ther information was desirable on a miscellany of products and processes of interest to the Petroleum Industry. Accordingly, Dr. Pier and a large number of other men of the I.G. Farbenindustrie, A.G. plant at Ludwigshafen/ Oppau were further interrogated in July-1945. The information contained in this report supplements that previously reported in the CIOS report of 16 August, 1945: "Report on Investigations by Fuels and Lubricants Teams at the I. G. Farbenindustrie A.G. works at Ludwigshafen and Oppau", edited by Lt. Col. R. Holroyd, (FP).

Aug 1, 1943

By R. A. Guereca

The Bureau of Mines conducted an analysis to determine criteria for steady-state, laminar flow boundary conditions for a coiled-tube gas viscosimeter by comparing experimental data from a thick-walled, stainless steel capillary in a horizontal, straight-tube condition, with similar data taken after the same capillary was formed into a helix. Overlapping volumetric f10wrates and pressure drops are covered for both configurations at pressure levels of 28, 225, and 1,000 psia at 3000 K. Friction factor, Reynolds number, and Dean number correlation plots show conditions where the coi1ed-tube flow deviates from straight-tube flow. The coiled-tube data indicate departure from Poiseui11e steady-state laminar flow at a Reynolds number close to 390 and a Dean number of about 15. Below these conditions and consistent with the data reported, Dean's circulation appears negligible. For the particular coil used, a conservative upper limit of 10 is chosen for the Dean number corresponding to an upper limit of about 250 for the Reynolds number.

Jan 1, 1967

By Andrew Allan

During recent years underground production for the Pennsylvania anthracite region has reached the lowest output per man per day figure of the last decade and a half. This fact, combined with increased unit costs for labor and material, has forced the market price of anthracite ever higher. Over the years the mines have become deeper, and haulage distances have increased, thus adding to the mining costs. The industry now recognizes the need for new mining techniques to offset increasing costs. The Federal Bureau of Mines, through its Anthracite Research Laboratory, is engaged in a program of underground-mining research in cooperation with anthracite-producing companies to aid in reestablishing the economy of the region by introducing methods and/ or machines that will reduce underground-mining costs and, at the same time, enhance the safety of the workmen.

Jan 1, 1953

By George T. Faust

The petrographic microscope plays an important role in the mineral dressing of nonmetallic materials. Petrographers and mineral technologists have evinced an interest in the technique developed, specifically, for mineral-dressing problems. The following dissertation makes the informa¬tion more generally available. ACKNOWLEDGMENTS The authors are indebted to O. C. Ralston, chief engineer, Nonmetals Division, and to Will H. Coghill, supervising engineer of the Southern Experiment Station for a critical reading of the manuscript. They are also indebted to their colleagues for technical information obtained in the course of cooperative work, in particular to J. B. Clemmer for the use of the data on fluorite.

Jan 1, 1940

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and. charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known, or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between metal and coal mine main airways, and the methods presented are equally applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine's proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions.

Jan 1, 1932

By P. T. Brooks

Semipilot scale tests were made to demonstrate a newly developed electrorefining process which could be extrapolated to commercial scale in producing high-purity nickel and cobalt from crude nickel metal and high-grade ferronickel. The new process comprises application of solvent extraction techniques to remove and separate cobalt and iron from nickel and the electrodeposition in diaphragm cells of pure nickel and cobalt from chloride-based purified electrolyte. Using water insoluble organic amines, the solvent extraction operations enabled production of commercial-sized nickel and cobalt cathodes of higher purity than that of commercial electrolytic metals. The solvent extraction operation for separation of cobalt from nickel was made simpler than the conventional method. Furthermore, the solvent. extraction operation for iron removal made possible the electrorefining of ferronickel without the prohibitive loss of nickel resulting from the method ordinarily used for iron removal.

Jan 1, 1970

By Otto Ruhl

As the result of a study of an area comprising some 100 square miles in the Missouri-Kansas Zinc district known to have produced zinc Ore from horizons below the Grand Falls formation, it was concluded that these horizons could become an important future source of zinc. To test this conclusion and to ascertain the general conditions associated with these lower-horizon ore deposits, the Bureau of Mines undertook detailed drilling of localities thought to be favorable for deposition of ore in the Reeds Spring and. Fern Glen formations. Two sites in the Galena, Kans., mining camp were chosen for this purpose. Ninety churn-drill holes totaling 19,338 feet of bore were completed by the Bureau in two campaigns that extended from October 1944 to June 1946. Approximately 25 percent of the holes encountered ore and indicated three separate ore bodies containing substantial tonnages. Observations made during the course of the work revealed that certain structural conditions are common to ore deposits in the Reeds Spring and. Fern Glen formations.

Jan 1, 1949

By M. L. Skow

Large tonnages of the manganese ores found in Aroostook County, Maine, are refractory to conventional mineral-dressing techniques and to the common chemical- extraction procedures. The Maple Mountain-Hovey Mountain ores are typical of this type. Because the most promising method of recovering the manganese from these ores has been a chloridizing roast in which the ground ore is in contact with gaseous hydrogen chloride, preliminary batch tests were made with a fluidized bed. On the basis of these tests, it was concluded that fluidization, with careful control of operating conditions, could be employed for this cloridization and warrants further study. Selective volatilization of the iron at 600° C. was unsuccessful. An operating temperature of approximately 950° C. was necessary for a practicable rate of volatilization of manganese chloride. Hydrogen chloride contents of 10 to 100 percent of the fluidized gas gave essentially equivalent manganese recoveries with an 80- minute retention time, For shorter periods reaction was more complete with the higher hydrogen chloride concentrations. At the 80-minute retention period the lower hydrogen chloride concentrations volatilized somewhat less iron and also improved the physical operation of the process. Fluidization gave results superior to comparable tests on chloridization in a fixed bed.

Jan 1, 1956

By Ralph V. Higgins

The present methods of appraising the long-range performance of oil reservoirs are based upon physical properties of the crude oil and the permeability of the reservoir rock. By means of these methods the performance of a reservoir may be estimated throughout its entire life. Before these methods were used, the future performance was estimated mostly by extrapolating pressure-decline curves -a method that is satisfactory for extrapolating only for a short period into the future. One factor that affects satisfactory long-range prediction of reservoir performance is the extent to which small changes in the physical properties of the oil and differences in the choices of relative permeability influence the calculated oil recovery. Selection of the physical properties of the samples to represent those of the oil and rock for the entire reservoir is difficult. This report is concerned with the error in calculated recoveries that may result from these inherent difficulties.

Jan 1, 1956

By Robert J. Anderso

Few elements have received more attention and developed greater interest in the last ten years than titanium. The substantially pure metal has been din...ie. cult to isolate, and so far has been little employed oommercially, but the use af alloys and chemical compounds of titanium has increased markedly in recent years. The earlier attempts at preparing pure titanium resulted in various impure forme which, from their metallic appearance, were always mistaken for the metal. Hunter in 1910 isolated pure titanium by the reduction of titanium tetrachloride with sodium. This brief statement is issued by the Bureau of Mines in response to numerous inquiries which have been received concerning titanium. More complete in. formation on the metal may be had by consulting the referenpes appended. The Literature is voluminous and only the more important references are Riven. It has been drawn upon freely in preparing this report; also information was supplied by M. g. Hunter, Arthur Braid, M 1. Schmid, C. M. Johnson, N. B. Hoffman, and de Courny Browne. The pioneer investigator in titanium is A. IL Rossi.

Oct 1, 1922

By J. H. Maysilles

The Bureau of Mines is conducting research on various technologies to recover alumina from domestic resources for feedstock to existing aluminum smelting capacity as a means to reduce dependence on imported bauxite, which represents 93 pct of U.S. aluminum requirements. One of the more promising technologies being investigated is the hydrochloric acid leaching of kaolinitic clay. In the hydrochloric acid leaching technology, alumina is recovered from iron-free aluminum chloride leach liquor and separated from impurity elements by sparging the liquor with HC1 gas to crystallize aluminum chloride hexahydrate (ACH). A large-scale crystallizer with a 336-gallon usable volume was constructed and operated to obtain engineering and design data for potential scale up and to demonstrate the ability of the technology to produce specification grade alumina. Test campaigns involving about 1,400 hours of operation were completed. ACH meeting all chemical purity requirements could not be produced by a single crystallization, but was produced by recrystallizing the product from the calcined kaolin clay leach liquor. Product crystals with a size distribution of more than 80 pct plus 100 mesh and 65 pct plus 65 mesh were made at a rate of 10 pounds of ACH/(hr)(ft3). The zirconium tube heat exchanger used to maintain constant process temperature operated with an over-all heat transfer coefficient of 420 to 500 BTU/(hr)(ft2)(°F).

Jan 1, 1981

By David L. Veith

Caustic scrubbing followed by silica flotation with cationic ether primary amine proved effective in upgrading commercial magnetic concentrates to supergrade products containing 2 percent SiO2, or less. Samples representing 41 million long tons per year of commercial magnetic concentrates from the Lake Superior region were tested by the Bureau of Mines. Bench-scale and pilot plant research indicated an estimated potential of 32 million long tons per year of superconcentrates to be available. Two pilot plant investigations yielded superconcentrates containing 1.1 and 1.9 percent SiO2 that were derived from commercial concentrates containing 7.0 and 4.2 percent SiO2, respectively. Corresponding iron recoveries were 90 and 93 percent at reagent costs of just over 33 cents per long ton of superconcentrates produced. Additional sources evaluated on a bench scale resulted in iron recoveries of 72 to 95 percent in products containing 1.7 to 2.0 percent Si02. Although reagent cost ranged up to 60 cents per long ton of superconcentrate, it is probable that these costs would be reduced in plant applications where benefits are derived from material and reagent recycle.

Jan 1, 1974

By I. L. Nichols, K. C. Dean, P. H. Johnson

Hydrochloric acid , sulfuric acid , and chloridizing roast- water leaching methods for dissolution of cesium and rubidium from Maine , Canada , and Southern Rhodesia pollucite ores and their flotation products were investigated by small- scale tests . Optimum conditions were determined to be ( 1 ) for hydrochloric acid leaching , use 12.7 equivalents of 8.8 normal acid per equivalent of cesium in the sample and leach for 6 hours at 100 ° C ; ( 2 ) for sulfuric acid leaching , use 12.7 equivalents of 14.4 normal acid and leach for 2 hours at 120° C ; and (3 ) for chloridizing roast - water leaching , roast minus 200 - mesh ore, limestone , and calcium chloride in a ratio of 2 : 4 : 1 , respectively , for 1 hour at 900 ° C , and leach the calcine for 1 hour at 80 ° C with enough water to give 35 pct solids . Extractions of cesium from ores and flotation products containing over 20 pct cesium were in excess of 97 , 93 , and 96 pct for the hydrochloric acid , sulfuric acid , and chloridizing roast - water leach processes , respectively .

Jan 1, 1964

By R. L. Schmidt

Research conducted over the past 20 years in France, Great Britain, and the United States on the use of the large-hole burn cut has established cer¬tain advantages for this system. Advantages include longer pull and more complete fragmentation from blast rounds. However, research is needed to establish a set of parameters for optimum performance. As part of the Bureau of Mines Advancing Mining Technology for Marginal Resources program, the Twin Cities Mining Research Center, Twin Cities, Minn., acquired a horizontal rotary drill capable of boring holes up to 24 in. in diameter. This was used for a series of underground experiments at White Pine mine, White Pine, Mich., during 1973. Exceptional results were obtained with a 12-1/4-in void hole that yielded up to 18 ft of pull in a 10- by 20-ft drift, Fragmentation was excellent, and the compactness of the muck pile facilitated loading.

Jan 1, 1975

By Ludwig Schmidt

Steel tanks often corrode rapidly in oil fields where the gas produced with crude petroleum contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion. Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide gas in solution, and has exhibited no serious corrosive action. These uses indicated that aluminum tanks might be equally effective in counteracting hydrogen sulphide corrosion. Consequently, in the spring of 1928, an all-aluminum stock tank of 500 barrels capacity and a "composite" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co. in Crane County, Tex. These tanks were under observation for one year, the test being sponsored by the Gulf Production Co., the Aluminum Co. of America, rind the Parkersburg Ric and Real Co. The results of this preliminary test sustained the belief that aluminum is highly resistant to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the Wake were not subjected to contact with the large quantities of highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of .the Aluminum Co. that additional tests be made to include production conditions in which large quantities of brine would be handled, for past experience had shown that aluminum often is susceptible to the corrosive action of brines.

Jan 1, 1931

By Ludwig Schmidt

[Steel tanks often corrode rapidly in oil fields where the gas produced with crude petroleum contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion. Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide L; as in solution, and has exhibited no serious corrosive action. These uses indicated that aluminum tanks might be equally effective in counteracting hydrogen sulphide corrosion. Consequently, in the spring of 1928, an all-aluminum stock tank of 500 carrels capacity and a "composite" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co. in Crane County, Tex. These tanks were under observation for one year, the test being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Real Co. The results of this preliminary test sustained the belief that aluminum is highly resistant to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the large quantities of highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the Aluminum Co. that additional tests be made to include production conditions in which large quantities of brine would be handled, for pact experience had known that aluminum often is susceptible to the corrosive action of brines.]

Jan 1, 1931