Search Documents

By R. C. Buehl

Pilot-plant tests have been in progress at the Bureau of Mines, Pittsburgh, Pa., on the recovery of manganese from open-hearth slag.3/4/5/ In the process, 1 the slag is first reduced in a blast furnace to make a high-phosphorus spiegeleisen containing 12 to 22 percent manganese. A slag containing 55 to 60 percent manganese is made from this spiegel by oxidation in a basic-lined converter. The metal from this blowing operation contains about 3 percent phosphorus, 1 percent manganese, and less than 1 percent carbon. Economic efficiency in the manganese-recovery process requires that this metal be converted into steel. Because of its high phosphorus content the metal is suitable for blowing in a basic-lined converter. In most of the tests described in this report, metal of this composition was used as the starting material in a 1-ton, side-blown, basic-lined converter. Although basic-lined converters are not used for steel production in the United states, in Europe a considerable portion of the steel is made in them. Open hearths largely have replaced converters for steelmaking in the United States; mainly because open-hearth steels have better physical properties than converter steels because of lower nitrogen and phosphorus contents. However, by improving converter design and operating technique during the past 15 years, metallurgists have found that low-nitrogen steels with physical properties equal to open-hearth steels can be produced in converters.6/ Tests at Jones & Laughlin steel Corp. with side-blown, acid-lined converters of 3 and 22 tons capacity showed that steel with a low nitrogen content comparable to that of open hearths operating on scrap charges could be made by surface blowing.7/

Jan 1, 1955

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Portugal, prepared from the best available information in Washington, has been slightly amplified in accordance with suggestions trans- mitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By G. W. Jones, F. E. Scott

"INTRODUCTION As a part of its program of promoting safety in mining and other industries, the Bureau of Mines investigates the explosion hazards of combustible Gases, vapors, and solids. It also investigates various means and methods of controlling and mitigating explosions.Dichlorodifluoromethane, CC12F2, has been found to be very efficient as a quenching agent for methane flames. 4/ This substance is a gas at ordinary temperatures and pressures and is relatively nontoxic and stable at mod rate temperatures.Tremendous quantities of dichlorodifluoromethane were used daring the late war as an expelling agent for aerosol mixtures in ""aerosol bombs."" At one time during the war the demand for Dichlorodifluoromethane became so gent that there was barely enough of it to supply the Army and Navy and virtually none for civilian needs. During this period of scarcity the Bureau of Mines, in cooperation with the Bureau of Entomology, Department of Agriculture, investigated the possibility of substituting other materials in part for the dichlorodifluoromethane. It was required that the resulting mixtures be satisfactory expellant and noninflammable under all normal conditions of use."

Jun 1, 1946

By R. V. Ramani

"In Part 1 of this two-part paper the characteristics of mine disasters and their effects are presented with case studies from coal, metal and non-metal mines leading to an amplification of their causes and opportunities for control. The disasters discussed encompass those which threaten the health and the safety of miners and those which affect the general population. In Part 2 of the paper, which will be published in the November 1995 issue of Natural Resources Forum, the approaches to hazard and disaster control are reviewed with particular attention to laws and regulations to promote health and safety at the workplace, and general welfare in mining communities. Further, a systems approach to disaster control is outlined.The mining industry is one of the three basic industries the other two being agriculture, and wildlife and fisheries. It is the process of mining which makes available the riches of the earth - the energy and mineral resources - to benefit humanity. In fact the progress of the human race through the ages is indelibly attached to prowess in exploiting these riches. The stone, iron and bronze ages are markers not just of a time in history but achievements of monumental proportions in the mining and beneficiation of natural resources. Even in agriculture, the remarkable success stories are associated with the prudent use of mined products to enhance production and productivity. The significance of a thriving mining industry to the wealth and security of a nation is therefore unquestioned.Unfortunately, the public's image of the mining industry is often associated with the mining disasters which receive wide coverage in the local and national media. Mine disasters command tremendous attention because of their infrequent occurrence and the extent of human suffering involved. Whether it is an explosion or a fire, or the opening or closing of a mine, the lives of people are touched by the personal and societal impacts of these events.Courts of inquiry of mining disasters have often concluded that the disaster situation was ever present and could have been detected with diligent search. In addition human error has been identified as one of the most frequent immediate causes for the precipitation of the disaster. For the most part, then, mining disasters are caused by man."

Dec 1, 1996

During 1990-1999, a total of 458 fires occurred in all coal mining categories; 157 of those fires caused 164 injuries and 2 fatalities. The greatest number of fues and fire injuries occurred at surface mines, whch also had the highest risk rate values. A total of 66 fuefighting interventions were required. Of these, there were 25 mine rescue team interventions in underground mines, including 5 mobile equipment firefighting interventions, and 41 fire brigade and fire department interventions at all surface operations, including 19 mobile equipment interventions. In all, 50 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 1 14 fires were detected late by smoke, and 42 fires were not detected.

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolaniccement concrete to develop a low- strength backfill . Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan ( fly ash ) and lime . Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressivestrength curves that can be used to estimate the best backfill mix for any mine .

Jan 1, 1964

By Frank J. Wiebelt

The Mohawk lead-zinc mining in San Bernardino County, Calif., was examined by D. W. Butnor, an engineer or the Bureau of Mines, at the request of Dunton, Ray, and Greenwood, leaseholders. Current operations were on a marginal economic basis, and government aid was sought in an endeavor to outline ore reserves so that production might be maintained.

Jan 1, 1949

By M. M. Fine

Small-scale laboratory mineral-dressing studies were made on a total of nine individual or composite samples of manganese-bearing material from the west-central Arkansas, or Mena, district. Of these, only three yielded concentrates that would probably be acceptable for purchases by the Federal Government fur the National Stockpile. Concentrates from some of the other properties, however, contained more than 40 percent Mn and might be merchantable to other purchasers of manganese ore. In most instances, a too-intimate association of manganese oxides and gangue is conducive to low grade, low recovery, or both, so that mechanical concentration processes do not promise much for this district.

Jan 1, 1956

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By Ivan F. Avery

OUTPUT of carbon black in 1959 increased in all producing States except New Mexico. The national increase was 20 percent. Domestic sales and exports increased 22 percent and 16 percent, respectively, resulting in a 21 percent gain in sales. Sales to the rubber industry, which purchased 95 percent of the domestic output of carbon black, increased 23 percent. Sales to all other major consumers also increased. Stocks decreased 82 million pounds during the year. [ ]

Jan 1, 1960

Develop technology that can reduce the dust exposure of a mine worker at the tailgate end of the longwall face by providing him with a clean split of air. Approach Use the jet spray air mover (JSAM) developed under a Bureau of Mines contract (refer to Technology News No. 117 for details on the development), to clean a small portion of the face air and to discharge the clean air behind a brattice partition. How It Works At most longwalls, air flows along the face from head-to-tail. Most of the airborne respirable dust generated along the face during mining is transported to the tailgate with the airflow. Any miner required to work at the tailgate is exposed to this dust. The only practical means of removing airborne respirable dust is with a scrubber. Simplicity and size made the JSAM the best choice for cleaning a portion of the tailgate air. The scrubber has no moving parts and is operated by water at low flow rates (<10 gpm) and fairly high pressures (250-500 psig). Many longwalls have sufficient water systems to supply the JSAM with adequate water pressures and flow rates. Also, the JSAM&apos;s size (4&apos;x 2&apos;x 1&apos;) allows it to be hung on one of the tailgate&apos;s shields or at some other convenient location. A clean split can be maintained at the tailgate by discharging the cleaned air behind a brattice partition at the work area. This should effectively seal off the clean air from the dusty air and provide the tailgate worker with a less dusty work environment.

Jan 1, 1983

By R. F. Abernethy

Analytical results, including ash fusibility data, are presented by the Bureau of Mines for 10 major constituents in coal ash from 373 samples of commercial U.S. coals. Determinations of Si02, Al2O3, Fe2O3, and P2O5 were made by colorimetric methods, Na2O and K2O by flame photometry, Ti02, CaO, and MgO by a spectrochemical method, and SO3 by a gravimetric method. In bituminous coal ashes the silicon, aluminum, and iron calculated as oxides often make up about 90 percent of the ash.

Jan 1, 1969

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

By R. L. King, J. Cervik, A. A. Campoli

The Bureau of Mines performed laboratory experiments to evaluate the triboelectric effect of particulate-laden gas streams on polyethylene pipe at various velocity, humidity, dust-size, and dust-load conditions. Charges in excess of 10 kV were produced on the outside and inside surfaces of laboratory pipe samples, when exposed to 40 pct relative humidity (RH) gas stream containing coal dust. However, no charges were produced in laboratory tests that duplicated the over 75 pct RH and dust-free gas streams found in working underground pipelines. Bare cop- per wire, which is wound around the polyethylene pipe in a 1-ft (31-cm) spacing and grounded, eliminated the charge on the outside surface of the pipe, but not on the inside of the pipe surface,

Jan 1, 1986

By Robert J. Hundhausen, GEORGE M. GRISMER

This circular describes the methods and costs of deepening the Silver Summit three-compartment shaft in the Coeur d'Alene mining region of Idaho. A noteworthy rate of advance was achieved at this operation by the successful use of a mechanical shaft-mucking machine. The Silver Summit mine is 1 mile west from the town of Osburn, Idaho, via U. S. Highway 10. The adit-level portal of the mine is on the south slope of the Coeur d'Alene River Valley at an altitude of 2,700 feet. The Silver Summit shaft is 6,000 feet from the portal. In past years this shaft had been sunk from the adit level to a depth of 1,500 feet. During 1946 the Polaris Mining Co, deepened it to 3,095 feet. The work was done under a co- operative development agreement between the Silver Summit Mining Co. and the Polaris Mining Co.

Jan 1, 1948

By N. S. Dalal, X. Shi, P. M. Gannett

"Chromates are known to induce tumors (1, 2), mutations (3), and DNA damage (4-6). However, the underlying biochemical mechanism(s) is (are) not fully understood (6). Recent studies have indicated that hydroxyl (·OH) radical may play an important role (7-11). The mechanistic studies of Cr(Vl)-related ·OH radical generation in biochemical systems have shown the reaction of a Cr(V) species with hydrogen peroxide (H20 2 } through a Fenton-like mechanism to be one of the important steps (9-11): Cr(V) + H20 2 - Cr(VI) + ·OH + OH-. (1)In biological systems the Cr(V) species are generated via the reduction of Cr(VI) by a variety of components, such as microsomes (12), mitochondria (13), mitochondrial electron transfer complexes (14), and at least three flavoenzymes (glutathione reductase (GSSG-R),3 lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase) (9, 15, 16). In the case of flavoenzymes, Cr(V) formation is accompanied by the reduction of molecular oxygen ( 0 2 ) to H20 2 • The Cr(V) species then reduces H20 2 to generate •OH radicals and Cr(VI) (16).To understarid the mechanism by which Cr(V}-generated ·OH radicals cause cytotoxicity, Aiyar et al. (8) investigated the reaction of Cr(VI) and H20 2 to generate ·OH radical and its reaction with 2'-deoxyguanine (dG) to form 8-hydroxy-2'-deoxyguanine (8-0HdG}:"

Mar 1, 1992

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill and blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963