Search Documents

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill und blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

"The following articles were produced through funding under Generic Mineral Technology Center for Respirable Dust research. Full articles appear in the proceedings, 3rd Symposium in the Mineral Industries, published in 1991 by the Society for Mining, Metallurgy and Exploration, Inc.Personal Diesel Exhaust Aerosol SamplerV.A. Marple, K.L. Rubow, and Y. TaoParticle Technology, Mechanical Engineering Department, University of Minnesota, Minneapolis, Minnesota(Section ill. Diesel I: Diesel Particulate Measurement, pp. 73-81)Abstract. Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective 18Dlpling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler.Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8 µm while mineral dust is greater than 0.8 µm.One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the nonrespirable particles while the inertial impactor state, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles ( <0.8 µ.m and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol."

Mar 1, 1992

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical studies have been prepared for the US Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which we may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to- noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna con- figurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National Bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by NBS. The recent NBS data is that used by Collins in the final predictions. The following outline indicates the order and subject matter treated in the subsequent sections: Section 2 - Signal-to-Noise Analysis for Loop-to-Loop Mine Communications Section 3 - The Horizontal Electric Dipole Section 4 - Signal-to-Noise Analysis for Down-Link Line Source Mine Communications Section 5 - LF Communication Section 6 - The Application of Recent NBS Noise Data to Mine Communications Section 7 - Analysis of Mine Communication Propagation Programs

Nov 15, 1974

By Joe L. Castagno, Kenneth H. Johnston

Several hundred membrane - filter tests were made as part of a program to develop equipment and procedures to evaluate the quality of waters and to determine the quality of water suitable to efficiently flood oil sands of known permeability . Results indicated that neither the color of the water nor that of the precipitate on a membrane filter is a criterion for determining the quality of injection water . Reasons for poor water quality include poor operation of filtering systems , dirty filtering aggregates , excessive amounts of oil in injection water , commingling of incompatible waters , and excessive use of chemicals . A good water is required to efficiently flood sands of low permeability , but fair results may be obtained in flooding more permeable sands with poorer quality water .

Jan 1, 1964

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By W. F. Marshall

This Bureau of Mines report discusses tests conducted with four different catalytic reactor designs to determine the influences of exhaust treatment systems on emissions from diesel engines. Although there was significant differences in oxidation efficiencies at light to intermediate engine loads, all four catalysts were very effective in reducing emissions at heavy loads. Compositional determinations included carbon monoxide, carbon dioxide, unburned hydrocarbons, oxides of nitrogen, aldehydes, sulfur dioxide, sulfates, and particulate loading. Particulate size, exhaust odor intensity, and the character of the unburned hydrocarbon component were also determined.

Jan 1, 1978

By V. A. Marple, K. L. Rubow, S. M. Behm

"An eight-stage cascade impactor, with cut-sizes ranging from 0.056 to 18 um at a flow rate of 30 L/min, has been developed, calibrated, and tested in field programs. This impactor, called a microorifice uniform deposit impactor, has several features not normally found in cascade impactors. Ultrafine particles as small as 0.056 um are collected while keeping the pressure drop moderate by utilizing multiple nozzles (up to 2000) as small as 52 um in diameter. At each stage the collected particles are deposited uniformly over the entire impaction plate by rotating the impaction plate relative to the nozzles and by the correct radial placement of the nozzles. The particle cutoff characteristics (collection efficiency curves) of each stage and inter-stage losses were determined by means of monodisperse aerosols. The cutoff characteristics were found to be sharp and similar for all stages.Inertial impactors are widely used for the size-selective collection of aerosol particles. One reason for their wide usage is that the principle of operation is simple: a jet of particle-laden air is directed at a flat impaction plate. Large particles are collected on the plate while smaller particles follow the airflow out of the impaction region and are not collected. The division between the size of particles collected and those that are not is quite sharp. Secondly, the particles in an impactor are classified by their aerodynamic diameter (an important size parameter in many fields of study, including those related to respirable particle health effects). Thirdly, it is easy to collect particles in discrete size ranges by passing the aerosol through a number of stages (one stage consisting of a nozzle and impaction plae) in series, with each subsequent stage collecting particles smaller than the one before it. This is known as a cascade impactor. Finally, impactors can classify particles over a wide range of particle sizes: as low as 0.005 um (Fernandez de la Mora et al., 1990) and as large as approximately 50 um (Vanderpool et al., 1987).This paper describes a general purpose cascade impactor that has been developed in our laboratory and used in a variety of studies including visibility studies (McMurry et al., 1986; McMurry and Zhang, 1989), underground mine studies (Marple et al., 1986; Rubow and Marple, 1988; Rubow et al., 1988), and general atmospheric pollution studies (Macias et al., 1981; Dzubay et al., 1984). The impactor, called a microorifice uniform deposit impactor (MOUDI model 100, MSP Corp., Minneapolis, Minn.), is the integration of two earlier impactor de¬velopments: the microorifice impactor (M01) (Kuhlmey et al., 1981) and the uniform deposit impactor (UDI) (Marple et al., 1981).The MOUDI has several features normally not found in other cascade impactors. These include collection of particles as small as 0.056 um in aerodynamic diameter with a moderate pressure drop, uniform particle collection on the impaction plates, inter-changeable impaction plates to allow for the plates to be easily and quickly changed in the field, and covers for these substrates to provide a means for safe storage and/or transport of the collected particles to the laboratory for analysis."

Mar 1, 1992

By R. R. Wells, K. C. Vincent, A. O. Ipsen

"INTRODUCTION The Philipsburg Mining District, Granite County, Mont., has been the largest producing area for battery-grade manganese (70 percent MnO2) in the United States since the First World War. Two companies, the Trout Mining Division of the American. Machine & Meals Co., and the Moorlight Mining Co., have intermittently mined and milled 120 to 250 tons of 25-percent manganese ore per day for the production of concentrates of this grade.Investigation of the district by engineers of the Federal Geological Survey and Bureau of Mines indicated that further exploration and develop¬ment would make available additional oxide and carbonate manganese ores for milling and production of metallurgical-grade manganese. If the battery-grade producers converted their plants to the production of metallurgical-grade concentrates, their production also could be increased through greater recoveries.Until February 1, 1944, the Metals Reserve Company, through its agent, the Sunshine Mining Co., purchased milling-grade manganese oxide and carbonate are for stock-piling at Philipsburg. After that time, only carbonate ore was purchased. Based upon the assumption that the stock pile was a true cross-section sample of the producing area, metallurgical studies were made on representative samples from the Metals Reserve stock piles. Testing also was conducted on two other samples of Philipsburg oxide manganese ore obtained by engineers of the Bureau of Mines from the Little Dandy claim of the Donlan group and from the Marie mine. All ore samples tested were found to be amenable to concentration by ore-dressing methods for the production of concentrates that when sintered met Metals Reserve Company specifications for metallurgical-grade manganese."

Nov 1, 1947

Objective Develop a method to warn of hazardous conditions and enhance safety during operation and inspection of vertical mine shafts and hoists. Background Mine hoisting is the most critical and potentially the most dan¬gerous operation in underground mining. Many hazards are related to falls of miners and materials, ground instability, and malfunction or lack of safety devices. All have the potential to cause a cata¬strophic accident. A condition known as "slack rope" is particularly dangerous, expecially if it occurs without the operator&apos;s awareness. The most common occurrence of slack rope is in metal or nonmetal mines that have a history of ground control problems near the "haft. Approach Studies of hoist safety features and Mine Safely a and Heath Administration (MSHA) accident statistics suggests a need to measure wire rope tension, conveyance speed and position, and shaft guide misalignment. The most accurate data are obtained directly from the conveyance. Such data could warn of potentially dangerous situations during hoisting operations, as well as during inspections, maintenance, and lowering of large equipment. Figure I shows the concept for monitoring wire rope tension, conveyance position, and guide displacement. Progress to Date A conveyance-mounted system has been developed that monitors rope tension: hoist conveyance position, speed, and load; and shaft guide misalignment. A "flex-beam" load sensor mounted just above the- conveyance protects against slack and tight rope. The measurements are transmitted 60 times a second via wireless equipment from the conveyance to the hoist room. An encoder mounted on the conveyance eliminates the need to correct the position because of rope stretch. Figure 2 shows the encoder wheel and guide displacement sensors being mounted on a cage in¬spection deck. A potentiometer monitors misalignment of the shaft guides during inspections. Information about the cage or skip can be acquired by the shaft inspector using a hand-held indicator. Inspection can also he conducted remotely from a station or hoist room using the wireless link to a laptop computer. Figure 3 shows test results from a simulated slack rope condition. Patent Status NIOSH has a patent pending on this device entitled "Cable-Load¬Sensing Device." For More Information NIOSH is seeking cooperators to assist in further tests of this technology to improve hoisting safety. Additional information can he obtained by contacting Michael J. Beus, Steven Iverson, or Elaine Cullen, Technology Transfer Officer, NIOSH, Spokane Research Laboratory, Spokane, WA 99207 at (509) 354-8000.

Feb 1, 1998

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By J. D. Kalasky, Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out- side headings of a set of five being developed in virgin area, and (2) conducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972

By R. V. Ramani, C. B. Manula, A. Owili-Eger

PART 1 THE INPUT AND OUTPUT DATA AND THE MINE SCHEMATIC SHOWING THE FLOWS FROM COMPUTER SOLUTIONS FOR APPLICATION I

Jan 1, 1975

By L. J. Froisland

Water classification and heavy-media sink-float methods were investigated for concentrating metallic junk automobile shredder rejects initially upgraded to about 75-percent metal content in an air elutriation system. An 8-inch-diameter water elutriation column with a feed capacity of 2.7 tons per hour was constructed and operated. The results obtained were compared with those produced by sink-float methods. Tests made on duplicate samples of an intermediate-grade metal product were successful in upgrading the metal con-tent from 75 percent to 98.7 and 99.1 percent with respective recoveries of 95.5 and 98.9 percent for the water classification and sink-float procedures. Tentative flowsheets for treating junk auto shredder rejects are outlined.

Jan 1, 1972

By Sol Weller

The Fischer-Tropsch synthesis consists of the formation of long-chain hydrocarbons by passage of carbon monoxide-hydrogen mixtures over metal catalysts, usually based on iron, cobalt, nickel, or ruthenium, at temperatures in the range 180°-300° C., and at pressures of 1-15 atmospheres. Although the reaction has been known and studied for more than 20 years, the mechanism by which it occurs is still poorly understood. One approach to understanding is to consider the effect upon the course of the synthesis of variations in each of the important operating variables. Consideration of the experimental data pertaining to these variables may suggest an over-all picture describing the synthesis - a picture which, in turn, would have to be consistent with all the known facts. The first part of this paper will be concerned with such a consideration of operating variables; the second portion will discuss recent work pertaining to the role of metal carbides as intermediates in the synthesis.

Jan 1, 1949

By Terry S. Cory

This report covers antenna design, analysis, and development work suited for use with a wireless radio communication system operating at medium frequency. The work includes the test and evaluation of prototype vehicular antennas developed during the program.

Jan 12, 1978

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By Arno C. Fieldner

Forty years have elapsed since the Bureau of Mines was established on July 1, 1910, by Act of Congress. The convocation of this Sixth International Conference of Safety in Mines Research Directors, 24 days after our 40th birthday, seems to be an appropriate time for reviewing our contributions to mine safety research and the problems yet to be solved from the American point of view. Actually research on safety in coal mines was started by the United States Government in the Technologic Branch of the U. S. Geological Survey of the Department of the Interior in 1908, as a result of a succession of disastrous coal mine explosions in which many lives were lost. In 1910 this work was transferred to the newly created Bureau of Mines. 394 lives were lost annually per 100,000 men employed in the coal mines of the United States in the 5-year period ended in 1910, as compared to 203 lives lost annually in the 5-year period ended with 1949. In 1908 no safe, permissible types of explosives and no certified permissible equipment of any kind were used in American coal mines. Black powder was in universal use and open oil or acetylene lights were common in all but mines known to be gassy. Rock dusting was not practiced to limit propagation of explosions, nor was ventilation in many mines adequate, Our safety practice lagged behind that of foreign coal- mining countries and therefore one of the first steps in carrying out the Congressional Authorization of 1908 to investigate the causes of mine explosions was to obtain assistance from the leaders of mine safety research in foreign countries. At the request of Dr. Joseph H. Holmes, director of the Technologic Branch of the Geological Survey, James R. Garfield, Secretary of the Interior, obtained the cooperation of the Governments of England, Belgium and Germany in sending Captain Arthur Desborough, Inspector of Explosives in England, Mr. Victor Watteyne, Inspector-General of Mines in Belgium, and Mr. Carl Meissner, Counselor for Mines in Germany, to visit American mines and make recommendations for increasing safety and efficiency in mining coal in the United States.

Jun 1, 1950

By John P. Capp

The feasibility of simultaneously burning several paths through a coalbed to develop a multiple path underground gasification system was investigated by the Bureau of Mines during two experiments, Boreholes were drilled through the overburden and into the coal and arranged in a circle approximately 50 feet from a central borehole. In the first experiment, in an area which had previously been hydraulically fractured,5 air was injected at the center borehole. The coal was ignited at the other boreholes and the fire fronts traveled toward the center, counter to the flow of air, to backward burn paths through the coalbed. Two paths were linked during the first 5 days of operation. The outlets of these two paths were throttled and air pressure was increased to maintain the flow of air, but no other linkages were made. Fourteen days after the two linkages these two paths were opened and gasification was carried on for 10 days, but with only moderate success. In an effort to overcome operating difficulties air was injected at the peripheral boreholes, and the gases were drawn off at the center borehole. Reversed flow operations continued for 12 days and two more paths linked. The heating value of the gas generally was higher than 100 British thermal units per standard cubic foot (B.t.u. per std. c.f.). Because only four of seven paths linked, however, the entire system could not be evaluated with respect to product-gas output and recovery of energy.

Jan 1, 1961

By G. E. Walden

The Bureau of Mines is currently engaged in a continuing investigation of the thermodynamic properties of certain inorganic compounds. As a part of this investigation, the heat contents of bismuth and cerous chlorides were measured throughout the temperature ranges of 370° to 630° K. and 370° to 1,200° K., respectively. Equations representing heat contents as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate heat contents at selected temperature intervals ranging from the ice point to 650° K. for bismuth chloride and to 1,200° K. for cerous chloride; also, the heats of fusion of both compounds were calculated at their respective melting points. EXPERIMENTAL Materials The cerous chloride used in this investigation was supplied by the National Carbon Company of Cleveland, Ohio. A chemical analysis indicated Ce 56.57 percent and Cl 43.39 percent. No attempt was made to purify the compound or identify impurities since the analysis showed only about 0.04 percent total impurities. Reagent grade bismuth chloride was used without additional purification.

Jan 1, 1961