Search Documents

By Harry R. Johnson

Laboratory experiments were conducted to study the carbon deposition characteristics of a high-gravity, paraffin-base crude oil. The results of these experiments indicate that a fuel supply adequate to initiate a combustion wave can be deposited in high-gravity-oil reservoirs. These results are significant because there has been considerable doubt whether oils over 35° API gravity are able to deposit sufficient fuel. Considered in these studies were the effects of air flux, temperature, initial oil saturation, and time on carbon deposition. Conditions that maximized carbon deposition in the laboratory and an understanding of the nature of carbon formation are shown by graphical interpretation of the data. Statistical techniques were used to design and analyze the results of the retort tests. For the same amount of laboratory work, this approach yields more information about the systems that were studied than the classical method of research presently used in many laboratories. In addition, the accuracy of calculating the effect of each variable on carbon deposition is twice that of the classical approach. This paper develops the statistical approach to research without complex mathematics, thus enabling the reader to grasp the concept of how statistics can be applied to study many complicated problems.

Jan 1, 1966

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were transmitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

By Noel N. Moebs

Five LANDSAT lineaments in the coal mining region of southwestern Pennsylvania were investigated by the Bureau of Mines to determine their geologic character, relation to subsurface conditions, and the means of discriminating one from another. The investigation included earth resistivity and very low frequency (VLF) electromagnetic traverses, soil moisture sampling, and a correlation with coal mine roof conditions. The lineaments could not be detected by the methods used, suggesting that they might be a surface phenomenon unrelated to subsurface geologic structures or roof stability in coal mine workings beneath.

Jan 1, 1987

From 1886, the first year shipments were recorded, until 1939, the Leadville district produced over 3,500,000 long tons of manganiferous ore. Of this total, metallurgical-type ores comprised 27 percent and manganiferous iron ores suitable for fluxing in lead smelters made up 73 percent. In 1939, the Bureau of Mines, as part of the strategic minerals investigative program being conducted at the time, requested the Mineral Industries Survey Section of the Mining Division to make a comprehensive study of the manganese resources of the Leadville area. This investigation, owing to the caved and flooded condition of the underground mine workings, was necessarily confined to a study of old maps, production records, and geological reports, and the results were published as an Information Circular in July 1940.

Jan 1, 1949

By S. H. Ash

The United States Bureau of Mines has published relatively little on the flooding and unwatering of coal and metal mines. Bulletin 229, Fifty-Nine Coal-Mine Fires, published in 1927, contains several instances of the flooding of mines or sections thereof to extinguish fires but does not describe their unwatering. Report of Investigations 2649, Explosion Hazards Incidental to Unwatering Coal Mines, published in 1924, warned against the possibility of gas accumulations in flooded mines and indicated the precautions to be taken. Report of Investigations 2255, An Unusual Hazard in Reopening Long-Flooded Timbered Metal Mines, published in 1921, told of methane being pocketed and the danger thereof. The flooding of mines originates in many ways. At some mines flooding followed reopening after what was thought to be permanent abandonment; also, explosions have caused some mines to be flooded. Extinguishing fires, accidental encountering of underground streams or flooded old workings, and caves of strata admitting water from underground workings, water-bearing strata, or surface accumulations have also flooded all or parts of mines. Unfortunately, un watering often necessitates much study and causes apprehension largely because experiences in similar situations are not generally known, as few descriptions of successful or unsuccessful methods are available. The job has sometimes been contracted for outside the local management involved and has become a matter of record for the contractor only. As the cost-plus contract system often employed in the past is now known to be expensive, careful managements elect to handle the problem themselves, in line with the general policy of cutting expense where possible. This report describes specific in-stances of successful unwatering by operators.

Jan 1, 1933

By Dougherty. E. Y., S. W. Zoldok, John W. Cole

"INTRODUCTION During its wartime program of exploration for minerals essential to the national economy, the Bureau of Mines was instructed to investigate sources of raw materials used in the manufacture of iron and steel. As a part of this investigation, some work was done on the iron deposits on the Neutral and Aztec claims on Buckhorn Mountain Canogan County, Washington, which was designed chiefly to indicate the nature and behavior of the ore deposits below the surface exposures. Diamond drilling was started in June and completed in July 1945. Preliminary laboratory tests on iron, ore from Buckhorn Mountain were completed during the fall and winter of 1945. This report presents the data obtained from the investigation.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final re¬port. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

Apr 1, 1947

By Cleo Griffith Rall, D. B. Taliaferro

The method for determining oil and water saturations described herein has been used successfully for several years in the core laboratories of the Bureau of Mines. The apparatus constructed according to the original specifications has proved very satisfactory; in fact, it has been widely adopted by core laboratories throughout the petroleum industry. The writers have found that the method gives reproducible results, the degree of accuracy depending largely on the attention to details given by the operator. The relative importance of these details of procedure and the design of the apparatus are discussed in this report. In September 1940, the Bureau of Mines published a report describing a method used in its laboratories for the determination of the water content of oil-field cores. The procedure was essentially the same as that adopted by the American Society for Testing Materials for the determination of the water content of petroleum products, although the apparatus and technique were altered slightly to increase the precision of the method and to adapt it to the characteristics of the material to be tested. The report also contained a description of the method used at that time in the Bureau’s core laboratories for measuring the oil content of a core, utilizing the sample on which the water-saturation determination had been made. The procedure involved the transfer of the weighed sample, from which the water had been distilled and measured, to a Soxhlet extractor and the removal of the remaining oil by means of a suitable solvent. Soon after the report was published, the water-determination apparatus described therein was modified so that both the oil and water contents of a core sample could be determined simultaneously. This method, which has been described by Yuster, is now widely used throughout the industry.

Dec 1, 1946

By N. S. Dalal, X. Shi

"The oxidation of NADPH by vanadate(V) in the presence of glutathione reductase showed typical enzymatic kinetics. The oxidation was inhibited by N-ethylmaleimide, a glutathione reductase inhibitor. Superoxide dismutase had no significant effect on the oxidation, indicating non-involvment of the superoxide radical. The vanadate(V) reduction was found to be a one-electron transfer process. These results suggest a new pathway for vanadate(V) metabolism and a new function of glutathione reductase. Compounds of vanadium(V), such as NaV03 , exert potent toxic effects on a wide variety of biological systems (1-3). Despite intense current activity, however, the biochemical mechanism of vanadate(V) toxicity is still not well understood (1- 14). It is believed that one of the important pathways involves the oxidation (by vanadate(V)) of NAD(P)H (15, 16), but, to our knowledge, there has been no report of the identification of any vanadate(V) reductase. With a view to finding if there exists any vanadate(V) reductase, we have investigated the oxidation of NADPH by vanadate(V) in the presence of glutathione reductase. Glutathione reductase (GSSG-R)2 was selected because our previous studies have shown (17) that GSSG-R can act as a reductase for chromate(VI), which is isoelectronic with vanadate(V). We find that GSSG-R does indeed function as a NADPH-dependent vanadate(V) reductase, thus pointing to a new pathway for the metabolism of vanadate(V), as well as to this property for GSSG-R. MATERIALS AND METHODSSodium metavanadate (NaV03 ), henceforth vanadate, was purchased from Aldrich and its solution was always freshly prepared. The GSSG·R used was from bovine intestinal mucosa and was purchased from Sigma. The oxidation of NADPH was followed photometrically as the decrease in absorbance at 340 nm. The spin trap, 5,5-dimethyl- pyrroline-N-oxide (DMPO), was purchased from Aldrich and used without further purification, since very weak or no spin adduct signal was obtained from the purchased sample when used alone.ESR spectra were obtained at X-band (9.7 GHz) using a Bruker ER200 ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR gaussmeter (Bruker, Model ER035A) and the microwave frequency was measured with a digital frequency counter (Hewlett-Packard, Model 5340A). An ASPECT 2000 computer was used for data storage and analysis. The concentrations given in the figure legends are the final concentrations. All experiments were carried out in the phosphate buffer solution (pH 7.2) and at room temperature."

Jan 1, 1990

By Wing G. Agnew, Paul L. Russell

"INTRODUCTION During the past few years, the development of millisecond-delay electric blasting caps has made possible a more flexible control over timing the firing of individual charges in blasting, The use of these caps has proved especially productive in quarry blasting and in numerous construction operations, but their use in underground mining is developing more slowly, although in some cases, as the solution to a difficult breaking problem, they have been well-received. When used in metal-mine drifts, the general objection is that the broken rock is thrown too far. In nearly all cases, however, use of millisecond-delay caps results in better fragmentation of the rock and a lower powder consumption per ton of rock broken.Prom 1949 to 1952, several series of experiments were conducted at the Mount Weather, Va., Experimental mine in conjunction with driving a 6- by 10-toot ventilation raise. 3/4/ The raise-round experiments in this 238-foot shaft, using millisecond-delay electric blasting caps in various drill-round patterns, are the subject of this report.SUMMARY AND CONCLUSIONSAll rounds discussed in this report were drilled in the hard rock (epidosite and greenstone) of the ventilation raise at Mount Weather Experimental mine (figs. 1 and 2). The drill-round patterns varied from 28- to 32 holes and from a V-cut design to one having no cut boles at all. With the exception of the first two rounds, all blasting was done with millisecond-delay electric blasting caps. In all rounds 60-percent ammonia gelatin dynamite was used and holes were stemmed with two cartridges of sand stemming."

Apr 1, 1953

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By Keith D. Rosbury

The basic objective of this project was to determine the cost-effectiveness of dust control used on unpaved mine haul roads. Field testing was conducted at three surface coal mines (two in Wyoming, one in southern Illinois) for a total of 20 weeks. The highest control efficiency measured for a chemical dust suppressant, 82 percent, was for calcium chloride two weeks after application. Generally, however, the control efficiencies hovered in the 40 to 60 per-cent range over the first two weeks since application, and then decreased with time. After the fifth week, the limited number of data points suggest a control efficiency of less than 20 percent. Composite watering data were fairly uniform. Watering once per hour resulted in a TSP control efficiency of approximately 40 percent. Doubling that application rate increased the control effectiveness by about 15 percent to 55 percent. Chemical dust suppressants (primarily salts and lignons) can be shown to be more cost-effective than watering under some conditions. Delta summaries and the analysis of data are contained in Volume I. Volume II contains basic data.

Jan 1, 1983

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

By R. V. Holmes

The properties of the Colorado Copper Co. in Sinbad Valley, Mesa and Montrose Counties, Colo., were rehabilitated and sampled by the Bureau of Mines in October, November, and December 1942. The several deposits were reexamined in March and April 1945 to obtain information disclosed by company work after December 1942. The development program included surface trenching, rehabilitation of several edits, and channel sampling of the exposures. Assay determinations wore made on 204 samples from the surface and underground workings. The results are given in the appendix. Several copper deposits in the Sinbad Valley area are similar in origin. The host rocks are sedimentary and mice in age from Pennsylvanian to Cretaceous. The Colorado No. 3 deposit occurs in the Cutler formation, which consists of many small lenses of conglomerate, sandstone, and shale. Mineralization is closely associated with faulting. On the Pyramid group the enrichment occurs in a zone of fracturing and jointing end also spreads into the adjoining sandstone. The ore deposition on the Copper Rivet claim is associated with a fault zone and is confined to en area above the contact of the Dolores-Wingate formations. Mineral deposits on the Sinbad claims occur at intersections of faults with blue-gray Pennsylvania limestone. Copper enrichment occurs along faults and as replacement of the surrounding limestone. Metallurgical tests indicate that ores from the Colorado No. 3 and Pyramid claims can be treated successfully by leaching with sulfuric acid. This method cannot be applied to ores from the Copper Rivet or Sinbad deposits because of high calcite content. Flotation tests at Boulder City, Nev., showed a recovery of less than 60 percent with a 14.24 percent copper concentrate.

Jan 1, 1952

By M. M. Fine

A preliminary mineral-dressing study of five samples of East Texas limonitic brown iron ores was conducted as part of the Bureau of Mines program to develop and extend domestic resources of iron ore. The samples were considered to be typical of ore currently being mined and beneficiated by the Lone Star Steel Co. and Sheffield Steel Co. The objective of the research was to investigate those mineral-dressing unit operations that might recover some of the fine iron lost in current industrial wastes or perhaps improve the recoveries when applied to the ores as well. Since current industrial beneficiation practice yields a washed limonite analyzing 41 to 45 percent iron, higher grade concentrates were not sought in this laboratory study. Laboratory investigation included washing and sizing, reduction roasting, and subsequent magnetic separation of the finely ground roasted materials. The results showed that laboratory recoveries of over 80 percent of the iron were possible, for the ores investigated, at concentrate grades comparable to those expected from cur-rent industrial beneficiation practice. ACKNOWLEDGMENTS Acknowledgment is made to the Lone Star Steel Co. and Sheffield Steel Co. for supplying the brown iron-ore samples on which this research was conducted.

Jan 1, 1956

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By W. H. Frederic, A. C. Fieldner, W. A. Selvig

"Low-rank coals have a pronounced tendency to disintegrate or ""slack” when alternately dried, and wetted by exposure to the weather. The more readily a coal slacks the greater is its tendency to ignite spontaneously and the more care must be used in its shipment and storage. Lignite slacks very readily when exposed to the weather. Slacking trouble is also experienced in shipping and storing subbituminous coal, but not to the same extent as with lignite. As a rule, bituminous coals are only slightly affected by weathering and in general may be classified as nonslacking coals. The slacking tendency of subbituminous coal is one of the characteristics that is used to distinguish it from bituminous coal. An accelerated laboratory method of test was developed to measure such slacking tendencies. This method was applied to a number of coals, principally from the State of Washington, and the method and the results obtained are given herein.Helpful information concerning slacking tendencies of coal was received from Marius R. Campbell, senior geologist U. S. Geological Survey.Coals that slack readily contain relatively large amounts of moisture. When exposed to the weather such coals lore moisture rapidly. As the coal loses moisture at the surface there is a gradual drift of moisture from the interior of the piece to the surface. If the loss of moisture at the surface proceeds at a faster rate than it is replaced by moisture from the interior of the coal piece, there undoubtedly in greater shrinkage of the coal at the surface as tom-pared to the interior of the piece and stressed are generated in the surface coal.These stresses in the surface coal cause it to crack and disintegrate.Likewise, when the air-dried coal is wetted by rain, the exposed surface of the coal pieces gain moisture more rapidly than the interior of the piece, causing greater expansion in the surface coal and the coal breaks down further. As this process of air drying and wetting is continued when the coal is exposed to the weather, the slacking proceeds and the exposed lumps of coal may disintegrate completely."

Nov 1, 1930

By J. W. Miller

Depletion of coals most suitable for metallurgical fuel has nude necessary a general survey of coking-coal reserves in the United States. These investigations were begun in 1948 at the joint request of the Munitions Board, Department of Defense, and a number of coal companies. This report, which is one of a series, by counties, describes the preparation characteristics of the coals of Letcher County, Icy. From these data it is possible to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable under present standards for producing metallurgical coke, (b) which coals require special and more intensive treatment in preparation than is now practiced, and, (c) which coals cannot be upgraded by known commercial preparation methods to metallurgical fuel standards now accepted.

Jan 1, 1955

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980