Search Documents

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use in a helicopter. Tests showed that EM signals from lightweight (314 lb) transmitters could be detected both on the surface and from a helicopter through -2 as much as 1650 ft of relatively high conductivity (2 X 10 mhos/m) over- burden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 7, 1973

By Lloyd A. Morley, Robert Stefanko

A major difficulty encountered during the research was that nation¬al countries (almost world-wide) are in the process of revising their electrical hazard reduction standards. Their principal goal is to align their standards with the International Electrotechnical Commission (IEC) Recommendations Publication Series 79. (31-37) Additionally, CENELEC is requiring all Common Market countries to harmonize their standards. (85) However in the coal mining industry some hazard re¬duction techniques are not being accepted because some systems may not be applicable. Therefore, past literature might not directly relate a country's current feeling about explosion-proof standards. An authority in the United Kingdom (which has been a leader in hazard reduction mainly through work at the Safety in Mines Research Establishment) brought up an additional point. (15) He hopes that since revising British standards BS229 into BS4683, with the intention of corresponding with the IEC 79 series, the recent CENELEC harmoni¬zation process will also follow IEC. (8, 9, 10) The past trend in other major Common Market countries prior to CENELEC's requirement results in the authors' speculation that the standards will be pattern¬ed after the IEC Publications. (5,17,60,84,102) Several letters were sent to the East Block countries but, disa¬ppointingly, replies were dispatched only from the USSR and Poland. Recent Polish standards (1973) were received, and a very close match to the IEC Publications has been noted. (76,77) Because of their economic community, it is extremely logical to assume that the East Block stand¬ards are therefore in concurrence with the IEC. Japanese specifications also appear to be compatible with the IEC Recommendations. (42,43)

Jan 1, 1974

By D. J. Bauer

A pure scandium solution was concentrated from 10-4 mole per liter to 0.5 mole per liter by continuous foam fractionation in a spaced, packed column. Recovery in the foam was 77 percent using a spaced, packed draining column with sodium n-methyl-n-"coconut oil acid" taurate as the surfactant. The technique was first studied batchwise in a small unpacked column to determine the more important variables. Optimum surfactant concentration was found to depend on scandium concentration. Extraction and, in general, enrichment ratios were highest in the 2.5 to 3.5 pH range at temperatures ranging from 50° to 70° C. An airflow rate of 136 ml./min. was satisfactory in the equipment used.

Jan 1, 1962

By D. C. Dahlin

The Bureau of Mines conducted laboratory batch beneficiation tests on samples from four potential platinum resources in southeastern Alaska to concentrate platinum and other precious metals. Thin Investigation was done as part of the mission of the Bureau to insure an adequate supply of minerals to meet the Nation's needs. Petrographic studies and beneficiation methods including gravity concentration, froth flotation, and magnetic separation were used to determine mineral association and to attempt to concentrate the platinum values with a primary mineral value such as chromite, copper sulfide, or magnetite. A high-graded sample from the Salt Chuck copper sulfide deposit yielded the platinum-group metal concentrate; the maximum grade attained was 0.04 oz Pt and 1.5 oz Pd per ton of high-grade copper sulfide concentrate. The other samples yielded low-grade primary mineral concentrates with low platinum-group values, and/or the platinum-group metals did not concentrate with the primary mineral value.

Jan 1, 1981

By B. Z. Zhong, T. Ong, W. E. Wallace, W. Z. Whong, Z. W. Gu, M. J. Keane

"Abstract-Diesel emission particles (DEP) from an engine operating on the Federal Test Procedure VDC were dispersed in an aqueous mixture of dipalmitoyl lecithin (DPL). a major component of pulmonary surfactant and saline and were tested for genotoxicity using the unscheduled DNA synthesis (UDS) assay with autoradiography techniques in cultured Chinese hamster lung cells. A DEP sample from the same source was dispersed in dimethyl sulphoxide (DMSO) and subjected to the same assay. Both dispersions (in DPL and DMSO) were found to induce UDS in a dose-related manner. After separation of the sample into supernatant and sediment fractions. the activity of the DEP sample was found to reside in the supernatant fraction for the DMSO-dispersed sample; and in the sedimentary fraction for the surfactant-dispersed sample. These findings further indicate that genotoxic activity associated with DEP inhaled into the lung may become bioavailable through the dispersion properties of pulmonary surfactant components.INTRODUCTIONTHE mutagenicity of diesel emission particles (DEP) has been studied intensively (LEWTAS and WILLIAMS, 1986). Carcinogenic effects of diesel exhaust in exposed animals have been reviewed (NIOSH, 1988) and an evaluation of carcinogenic risks to humans from diesel engine exhausts has been published (IARC, 1989). Using components of pulmonary surfactant such as dipalmitoyl lecithin (D PL), dipalmitoyl phosphatidylethanolamine (DPPE) or dipalmitoyl phosphatidic acid (DPPA) dispersed in physiological saline, we have previously shown that diesel soots express mutagenic activities in the Salmonella histidine reversion assay system and in the sister chromatid exchange assay using the cultured Chinese hamster lung (V79) cells. Mutagenic activity of diesel soots dispersed in DPL, DPPE and DPPA was quantitatively comparable to and in some cases greater than, the activity expressed by an equal mass of soot extracted by dichloromethane-dimethyl sulphoxide (DCM-DMSO) (WALLACE et al., 1989).Unscheduled DNA synthesis (UDS) is accepted and frequently included, as one of the tests in the battery of assays used to assess carcinogenic-mutagenic potential -of chemicals (MITCHELL et al., 1983). In this study, induction of UDS in V79 cells by DEP, dispersed in the major component of pulmonary surfactant DPL, was carried out. The purpose of this study is to validate the suggestion generated from our previous work that mutagens associated with inhaled particles may be dispersed or solubilized in the phospholipid component of pulmonary surfactant and become active in such a phase (WALLACE er al., 1989) and to test the fractionated DEP sample using UDS assay for a more complete evaluation of its genotoxicity."

Dec 1, 1995

By N. S. Dalal, X. Shi

It has been known for more than a decade that vanadium (V) stimulates the oxidation of NADH by plasma membranes (1) but the underlying mechanism is still not fully understood. This effect has been attributed to a membrane-associated NADH-dependent vanadium (V) oxidoreductase (1). Subsequent studies suggest that vanadium ( V) can accept an electron from fiavoprotein dehydrogenase that oxidizes NADH (2). The phenomenon ofNAD(P)H oxidation coupled to vanadium(V) reduction has also been demonstrated in other biological systems (3-6). A recent electron spin resonance (ESR) study from our laboratory reported on the accumulation of vanadium (IV) duringthe reduction ofvanadate (vanadium(V)) by the ftavoenzymes glutathione reductase (GSSG-R),4 lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase in the presence of NAD(P)H (7). It was concluded therein (7) that these ftavoenzymes function as NAD(P)H-dependent vanadium(V) reductases. More recently, however, Liochev and Fridovich (8) have argued that the ESR data (7) do not demonstrate that the investigated fiavoenzymes act as vanadate reductases. They suggest an alternative mechanism in which the fiavoenzyme simply serves as a generator ofsuperoxide (02) radical, which acts as a propagator of the radical chain reaction leading to NAD(P)H oxidation (9, 10), as summarized below:

Nov 1, 1995

By E. J. Gleim

"When permissible equipment is first placed in a gassy mine, those in charge may not realize the amount of attention and care they must give it if they intend to secure its full value as safety equipment. If permissible machines are installed as a safety measure, then they must receive regular, intelligent inspection and upkeep to forestall the development of unsafe features.Certain fundamentals have been followed in the design of this type of equipment in order to minimize the possibility of its igniting gas and dust. Hence, some knowledge of these fundamentals is essential to the inspector or official charged with the duty of ascertaining the condition of permissible machines with respect to safety. Familiarity with the constructional details of a machine is of first importance in making a thorough inspection of it. A knowledge of Schedule 2C3 which gives the requirements for practically all types of motor operated equipment receiving the United States Bureau of Mines' approval is also a requisite.There are certain special features in the construction followed by different manufacturers that can not be made clear for the purposes of inspection except by a lengthy description which would be inappropriate in this paper. There are, however, some general points that are applicable to the inspection of any machine employing trailing cable for connection to the power supply, also some that apply to any permissible storage-battery locomotive.The following list, based on the writer's experience in making field inspections, gives these general points in the form of questions which may he used as a guide by the inspector. A brief explanation is given after each question so that the reason for checking up on each point will be understood.1. Is a U. S. Bureau of Mines' approval plate attached to the machine? (Such a plate is necessary in order to establish identification as a permissible machine.)2. Is approval plate clean?(The plate should be clean so that the precautions enumerated on it are readable.)3. Is trailing cable protected by a fuse or other automatic circuit-interrupting device?(Trailing cable must have a fused trolley tap or other suitable means for short-circuit protection in case the cable is run over or splices fail. Proper fusing will minimize the possibility of fire in the cable reel.)4. If a trolley tap is used, does it contain a fuse of the proper capacity? (A piece of trolley wire or, too large a fuse may entirely defeat the purpose of fusing.)5. If a fused trolley tap is not used, how is connection made to the power supply? (The end of the trailing cable must be fitted with an insulated arrangement to minimize shock hazard when connecting the cable to the power supply.)6. Are the main fuses (or overload relays) of the correct size (or setting) for protection of the machine against overload?(Too large a fuse or too high a setting of the overload relay will permit damage to the machine by abuse through sustained overloads.)7. If the machine has a headlight, does the headlight circuit have overload and short-circuit protection?(The wiring of the headlight circuit on a machine is usually of a smaller size than that for the main circuits and therefore requires fuse protection proportionate to the size of wire.) Note: This same question may be asked relative to coal drills sometimes mounted on a machine."

Apr 1, 1932

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962

By G. W. Weems

The Bureau of Mines combined preconcentrating techniques and mass spectrometry to develop a parts-per-billion general analysis of impurities in helium. The impurities are preconcentrated using a Bureau trace-impurity analyzer; 35-mm Hg pressure of helium is left in the concentration trap to sweep the impurities into the mass spectrometry and provide a 10-mm Hg sample pressure.

Jan 1, 1966

By J. Mutmansky, C. Lee

"The size distribution of coal mine dust is one of its most important characteristics because the particle size is known to govern the region of deposition of dust within the human respiratory tract. In addition, dust characteristics, particle settling rate, transportability of the dust and the efficiency of dust control measures are all affected by the particle size. As a result, particle size distribution of the airborne dust in a coal mine is a fundamental property that impacts on the health of underground workers.This paper deals with some basic findings on the size distribution of cool mine dust based upon the results of data collection in six underground coal mines using continuous miners. All airborne dust sampling was performed on development sections using eight stage cascade impactors and permissible 2. O l / min pumps. Samplers locations were fixed in the sections with respect to the continuous miner and roofbolter or with respect to the intake and return airways • Sampling times varied from 45 minutes to 6 hours , depending upon the dust concentration. The first topic of analysis was the test to determine whether the commonly used lognonnal distribution is valid when applied to airborne coal mine dust. Secondly, the conventional method of representing the· distribution using two parameters, the geometric mean and the geometric standard deviation, is questioned. Since almost all size data were found to show some degree of bimodality, the two parameter lognonnal distribution may not represent the total airborne coal mine dust size , quite adequately. Bimodal lognonnal distribution was tested to be a good approximation in the case with two modes in the size distribution.The final topic discussed in this paper is the 'locational variation of the airborne dust size distributions within the continuous mining section. The size distributions varied considerably at the different sampling locations with the continuous miner and roofbolter producing the coarser distributions. Fine size modes in the range of 2 to 4µ m including mostly respirable dust particles were present in almost all samples • Second dust generating sources such as the shuttle car movement were found to be major causes of high respirable dust concentrations in some cases ."

Jan 1, 1988

A significant amount of information regarding the crushed stone and sand and gravel industries in each State is available from State agencies and State trade associations. These organizations continuously monitor the State mineral industries and are therefore an important source of detailed information at the local level. This third edition of the directory was prepared to provide a listing of government agencies and trade associations that can assist the users interested in obtaining detailed listings of crushed stone and sand and gravel producers, in addition to the information published by the U.S. Bureau of Mines.

Jan 1, 1994

By Ronald A. Vary

This paper is one of a series prepared by the United States Bureau of Mines dealing with milling methods and costs. In view of the current revival of interest in gold mining, information dealing with practices and costs in the development of gold properties is apropos. Milling practice at a small gold property in the prospect stage is described where, with a small outlay for plant and equipment, development has been carried on for about 20 months on the proceeds of the mill operation with little additional expenditure. The paper shows about what may be expected as to costs at a small property operated under northern climatic conditions and with rigid economy throughout the plant.

Jan 1, 1931

By W. O. Vanderburg

This paper describing the methods of concentrating tungsten pros at the mills of the Atolia Mining Co. is one of a series of similar papers being prepared by the United States Bureau of Mines. The writer acknowledges the assistance and cooperation of A. V. Udell, president, Louis Warnken, bookkeeper, and C. K. Dennis, superintendent, of the Atolia Mining Co. in the preparation of this paper.

Jan 1, 1931

By L. M. Chan, D. H. Carlson, J. H. Johnson

"This paper discusses the evaluation and application of a portable parked-vehicle tailpipe emissions measurement apparatus (EMA). The EMA consists of an exhaust dilution system and a portable instrument package. The EMA instantaneously dilutes and cools a sample of exhaust with compressed nitrogen or air at a known dilution ratio, thereby presenting it to instruments as it is presented to personnel in the surrounding environment. The operating principles and governing equations of the EMA are presented.A computational method is presented to determine the engine operating and performance parameters from the exhaust CO2 concentrations along with an assumed engine overall volumetric efficiency and brake specific fuel consumption. The parameters determined are fuel / air ratio, mass flow rates of fuel, air and exhaust emissions, and engine brake torque and horsepower. These calculated engine parameters are used to characterize engine load when performing EMA in-field tailpipe sampling without a dynamometer, and to detect deteriorated engines.Evaluations of the EMA by comparison of diesel tailpipe measurements with those made using laboratory-grade instruments showed that the EMA measurements are accurate and reproducible. The results also show that the EMA is capable of detecting emission concentration changes resulting from engine faults. Calculated engine operating and performance parameters correlate and compare well with laboratory-measured values.The EMA in-field engine loading and tailpipe sampling procedures for parked vehicles are presented, and results of the EMA field measurements are also presented. Low coefficients of variation for repeat EMA tailpipe measurements on diesel-powered haulage vehicles in four underground mines indicate that the EMA in-field engine loading and tailpipe sampling procedures are reproducible.An analysis of EMA tailpipe measurements for three haulage vehicles in one mine shows that the EMA can: 1) identify haulage vehicles that emit excessively high pollutant concentrations, and 2) provide data needed to evaluate and determine the efficiency and effectiveness of tailpipe emission control devices.Finally, recommendations for a proposed commercial EMA system are presented. This commercial system would overcome many of the adverse features of the prototype EMA used in these tests."

Mar 1, 1992

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

By L. B. Pankratz

Enthalpies were determined for synthetic chalcopyrite (CuFeS2) between 298° and 1,050° K and for synthetic bornite (Cu5FeS4) between 298° and 1,100° K by copper-block drop calorimetry. Two transitions were found for each compound. The lower transitions were both crystal transformations from tetragonal (low-temperature form) to cubic (high-temperature form). The chalcopyrite transformation occurred at 830' K with a heat of transformation of 2,405 cal/mole; the bornite transformation was at 485° K with a heat of 1,430 cal/mole. The other transitions were of the second order and were presumed to be magnetic in character. The second-order transitions for chalcopyrite occurred at 930° K, and the one for bornite at 540° K. Enthalpy increments, entropy increments, and heat capacities are tabulated at even temperatures above 298.15° K. Equations of enthalpy are also given.

Jan 1, 1970

This is an audience, I know, that shares my interest in a subject that is currently getting a lot of attention -the tendency of our Nation to draw increasingly on overseas supplies of certain mineral commodities, and proportionately less on domestic sources for these minerals. That we do obtain substantial quantities of some essential minerals from abroad is easy to demonstrate. That we will continue to do so in the foreseeable future is not in doubt. Uncertainty begins, however, when we try to interpret the significance of these facts. As with many phenomena, their meaning is open to a variety of interpretations.

Jan 1, 1980

By H. A. Watson

Fluorine-containing polymers are comparatively new materials that exhibit very desirable characteristics not usually found in non-fluorine containing polymers. Among these characteristics are heat and flame resistance, desirable electrical properties, and chemical inertness. Polytetrafluoroethylene and polymonochlorotrifluoroethylene are examples of such polymers commercially available. In practical applications it is reasonable to expect thermal position of these materials if they are subject to high enough temperatures. The temperatures at which thermal decomposition takes place and the nature of the gaseous products of decomposition are considered pertinent data in intelligent use of these materials. The purpose of the tests discussed herein was to determine: (1) The temperatures at which gases were produced when small specimens of the two polymers were located and (2) determine the identity of the major constituents of gaseous products.

Jan 1, 1950

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed list of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have been modified as covered by extensions of the original approvals.

Jan 1, 1941