Search Documents

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

By R. V. Ramani, P. M. T. White, D. Sutton

3.1 Criteria for Selection A coal deposit has the following major characteristics: i) wide distribution as a flat-lying, thin, bedded deposit ii) stable nature of its major components and ranking characteristics such as carbon, heat content, volatile components, specific gravity, etc. iii) number of constituents and characteristics which under present regulations limit usage, such as content of ash, sulphur, sodium, etc. iv) effect of characteristics of over- and under- lying host rocks including porosity and permeability, lithology and general geology v) low value, high bulk nature. Because of the relative stability of its major components and its low unit price, coal does not require the same attention to detail as do the metal deposits. However, new regulations combined with social pressures make it imperative that more accurate information be made available concerning factors which affect the quality of coal and which may have an adverse effect on the environment when the coal is mined or burnt. The method selected for the evaluation of a coal deposit must, therefore, be flexible and sensitive enough to be used to interpolate stable parameters whose general distribution character-

Jan 1, 1974

By R. V. Ramani

"In Part 1 of this paper, published in the August 1995 issue of Natural Resources Forum, a review of several mining disasters around the world established the complex nature of their causation and their catastrophic effects. The involvement of human beings, either through acts of commission or omission, was highlighted. In Part 2, a discussion of the various approaches to disaster control, mostly as practised in the USA, is presented. A systems approach to disaster prevention incorporating elements of hazard identification, mine design, emergency response and post-emergency audit is presented.In the USA the role of government in the affairs of its citizens is continually growing. This role is intended to ensure an unimpeded pursuit of happiness and prosperity by the population and to curtail actions which are restrictive or harmful to the citizenry. The passage of a legislation is an indication that it has been decided through the established process that the activities covered by the legislation should receive appropriate consideration. The enactment of the Coal Mine Health and Safety Act of 1969 (The 1969 Coal Act), the Mine Safety and Health Amendment Act of 1977 (The 1977 Mine Act) and the Surface Mining Control and Reclamation Act of 1977 (The 1977 Surface Mining Act), was specifically intended to further the role of government in the health, safety and environmental affairs of the mineral industry.Currently, the federal government's responsibilities for mine safety and health are divided among three agencies: the Mine Safety and Health Administration (MSHA) in the US Department of Labor, the Bureau of Mines (USBM) in the US Department of the Interior and the National Institute for Occupational Safety and Health (NIOSH) in the Department of Health and Human Services (National Research Council, 1981). MSHA is responsible for issuing and enforcing mine safety and health regulations, for training miners and for responding to mine emergencies. The Bureau of Mines is responsible for conducting research on mine safety and on the technological means for reducing health and safety hazards in mines. NIOSH conducts research relating to miner health, and together with MSHA, tests and certifies devices used to detect hazardous materials in mines and protective equipment used by miners. NIOSH also plays a public health role in that its activities in mining include health hazard evalua¬tions, general mining surveillance as mandated by law and medical surveillance including coal miner X-ray and autopsy programmes. MSHA shares with the Bureau of Mines the responsibility for integrating R&D results into operational practice. MSHA implements R&D results either by incorporating them into its own operations or by rule making that requires new practices or equipment to be adopted by the mining industry. In many instances, the Bureau's R&D results have been adopted by the mining industry without rule making."

Dec 1, 1996

By Ben A. Kornhauser

Petroleum production was the principal component of the mineral industry, followed by cement production and some salt output. The French Central Fund for Economics Cooperation loaned $9.15 million2 to the Communauté Electrique du Benin (CEB), which served Benin and Togo, toward financing the construction of a dam on the Mono River at Nangbeto, Togo. The dam was to supply hydroelectric power to reduce the energy dependence of the two countries and to irrigate crops. Nine other international financial organizations, including the International Bank for Reconstruction and Development (World Bank). the African Development Bank, the Arab Bank for African Economic Development, and the French Aid and Cooperation Fund, contributed to the estimated $140 million cost of the dam. The CEB also was to contribute to the financing. Contracts amounting to $60 million already had been awarded to West German and Canadian firms. The dam was expected to be completed in 1987.

Jan 1, 1986

By P. D. Laverty

The U.S. Bureau of Mines treated mixed and contaminated super alloy scrap by pyrometallurgical and hydrometallurgical methods to separate and recover metal values. Best results were obtained by leaching Zn-treated or atomized scrap with HCI-02 at 9SO C and 50 psig 02' This resulted in dissolving approxi-mately 98 pet of the AI, Co, Cr, Cu, Fe, Mn, Ni, and Zn while rejecting over 98 pct of the Mo, Nb, Ta, Ti, W, and Zr as an insoluble refractory residue. Chlorine was successfully substituted for HCI to leach Zn-treated scrap but was unsuccessful for leaching atomized scrap. The leaching solution was treated by pH adjustment and hydrothermal precipitation at 2000 C for 4 h to remove AI, Cr, Fe, and other contaminants as a filterable precipitate. Recovery of Co and Ni would be accomplished by solvent extraction and e1ectrowinning. Chromium recovery as a ferroalloy was demonstrated.

Jan 1, 1989

By John C. Edwards, Gene F. Friel, John J. Opferman, Robert A. Franks

As the use of deep -rut mining increases, there - expected to be a greater demand for methane (CH,) measurement devices capable of scanning working faces al depths in excess of 10 m to alert mine personnel of hazardous concentrations of CH and to satisfy regulatory requirements. Remote optical devices offer the most promise to satisfy these objectives while the operator remains safely under supported roof. A second¬-generation remote Optical methanomeor (ROM) bas been designed and Is undergoing laboratory evaluation at the National Institute for Occupational Safety and Health. It operates on the principle of differential absorption of the "u;' fundamental absorption band of CH, centered at 3.31 um in the infrared region of the spectrum. The new instrument differs from the previous prototypes by the replacement of the two hand pass differential absorption technique of measurement with a single filter gas correlation technique and a refinement of the amplifier and gating circuitry used within the unit. This results in a more accurate isolation of the CH, spectral absorption band centered at 3.31 um. A specially designed 0.4m-diam variable-length gas mixing tunnel was constructed and instrumented with CH4 sampling capability to calibrate the ROM. Experiments have demonstrated the ability of the detector to respond to various conditions of CH, (pn•m) at distances as great as 12 m. Thermal radiation generated within the instrument is the controlling factor in the drift of the output signal nod, therefore the reliability of the instrument. Several approaches to reduce this extraneous radiation interfering moth the infrared detector, described, such as the installation of a fan in the instrument and thermoelectric coolers on the detector's beat sink. Implementation of this technology will significantly improve the safely of miners.

Jan 5, 1997

By W. M. Weigel

"Sand is one of the commonest materials for industrial use, not only as a building material, but in many industrial processes. The general name applies to all grades, from the comparatively impure, unsorted product used in concrete, to especially sized products of extreme chemical purity. Various definitions have been proposed, all more or less open to objection, as they fail to cover special applications. One is: ""Sand - The fine granular material naturally or artificially produced by the disintegration or crushing of rock or slag"". This does not fit the definition of sand as understood by geologists, who consider sand only as a naturally formed product. Another is: ""Sand - The fine granular material naturally produced by the disintegration of rock"". This does not take the chemical com-position into account, and for practically all uses, except in concrete and plaster products, a material composed predominantly of silica or rather quarts is implied.Sand for special purposes usually requires different methods of preparation from those where the ordinary mixture of sizes as naturally occurring are suitable. One of the classes requiring the most uniformly sized grains is sand blast sand.Sand Blast SandThe use of the sand blast has increased rapidly during the past few years. It was formerly used almost entirely in the foundry to clean and remove inequalities from rough castings. This is still the most important application, but in addition, it is now employed for the removal of paint from old surfaces, carving and engraving on stone and marble, glass cutting, cleaning or renovating the rails of stone and brick buildings that have become discolored, preparing the surface of metals for the electrolytic bath, putting the final finish to metal surfaces, and has even been proposed as a means of channeling or cutting out blocks of stone in the quarry."

Jun 1, 1924

By M. C. Simmons, Boyd Gutorie

Desulfurization experiments at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville on virgin light distillates obtained from some ‘high-sulfur’ crude oils have shown that the octane numbers of the original distillates are increased on the average about one unit, that the octane numbers of distillates with 4 ml. tetraethyl lead are increased 2 to 3 units, and that the The Petroleum Experiment Station, at the request of the Petroleum Administration for War, instigated and has in progress an investigation of crude oils of the United States to determine their possibilities for yielding straight-run distillates suitable for use as base or blending stocks to produce high octane aviation gasoline. One phase of this investigation deals primarily with so-called ‘high-sulfur’ or ‘sour’ crude oils by seeking to determine the effects of sulfur removal upon the virgin distillates prepared from these crude oils. To date, virgin distillates from several ‘high-sulfur’ crude oils from Texas, New Mexico, and Oklahoma have been prepared and desulfurized in pilot-plant distillation and desulfurization units at the Petroleum Experiment Station. The properties of the undesulfurized and desulfurized distillates were determined and compared to show the effect of sulfur removal. Results of these investigations showing the suitability of these crude oils as sources of virgin naphtha aviation base stocks have been prepared and forwarded to the Petroleum Administration for War and other approved persons. The following preliminary summary is presented to acquaint those interested not only with the present results of the investigation of several ‘high-sulfur’ Texas, New Mexico, and Oklahoma crude oils, but also to give some basic information as to certain sulfur compounds, especially their identification in straight-run distillates, their depressing effects upon the octane numbers of leaded fuels, the benefits obtained by their partial and complete removal, and some of the processes being used to effect their removal.

Nov 1, 1943

By M. K. Larson, J. K. Whyatt, F. M. Jenkins

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [F . 135 MPa (19,600 psi) oriented S 80E1W]. An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 1995

By J. M. Stuve

Calorimetric determinations of the low-temperature heat capacities, standard enthalpy of formation, and high-temperature enthalpies were made of (Na20)4 ?Fe20,(c). The resulting values of entropy (S°), enthalpy of formation (?Hf°), and free energy of formation (?Gf°) at 298.15° K are 104.676 cal/deg mole, -656.2 ±.kcal/mole, and -603.4 A kcal/mole, respectively. Tabulations of Cp°, S°, - (G°-H°298)/T, H°-H°298, ?Hf°, ?Gf°, and log Kf are given to 1,200° K.

Jan 1, 1971

By H. Kim, R. W. Plummer, T. J. Stobbe

"The probability of developing coal workers' pneumoconiosis (CWP) varies among miners in different geographic areas, coal seams, and jobs. Many studies have revealed the correlation between mineral content and the frequency and severity of CWP development still remains controversial. Furthermore, the mineral content and its variability in different areas is unknown.Since mineral content is expected to vary from location to location within a mine, between mines, between coal seams, and over time, this information will be valuable in understanding the variations in CWP incidence, as well as in establishing the appropriate kinds of dust to use in toxicological research programs studying CWP.Size-selective airborne dust samples were collected using 4-stage cassette impactors at 9 different locations in each of five coal seams. These coal seams were the Upper Freeport, Pittsburgh, Kittaning, Coal Burg, and Pocahontas. Mineralogical analyses were done by a x-ray powder diffraction photographic technique.Common minerals found in coal mine dust were illite, calcite, kaolinite, quartz, siderite, dolomite, gypsum, anhydrite, and pyrite. The distribution of minerals in interand intra location samples will be reported. Early results on the mineral content show wide variations between locations.in a mine and between coal seams, and small, but significant, variations between particle sizes.INTRODUCTIONIn spite of its long history of incidence, and the large amount of research conducted on it, coal workers' pneumoconiosis (CWP) is still prevalent among coal miners and needs further research to develop effective preventive and remedial measures. Although the dose-response relationship between simple CWP and coal mine dust has been established (1), the causal agent(s) and the mechanism(s) involved in the progression of simple to complicated CWP are not yet defined. Many plausible hypotheses have been made to explain the mechanisms involved in the disease progression however none of them is satisfactory. In addition, the source of variation in occurrence of CWP among miners in different geographic areas (2), rank of coal seam (3,4), and job (5) remain unsolved."

Jan 1, 1988

By J. L. Stauffer, L. Gaydos, L. M. Demers, D. C. Kuhn

"Eicosanoids and cylokines produced by the pulmonary alveolar macrophage (PAM) are key mediators for the defensive role this cell plays in neutralizing the inhalation of particulate dusts and foreign microbes. However, these factors are also mediators of inflammation and their uncontrolled release may cause the lung injury and liorotic changes observed in individuals exposed occupationally to mineral dust. In vitro studies have suggested a link between the production of certain eicosanoids and cylokines released from the activated PAM. To this end, we have studied the release of eicosanoids (PGE2, TXB2 and LTB4) and cylokines (IL-1 and TNF) by cultured PAM, obtained from healthy human volunteers by bronchoalveolar lavage under basal culture conditions and following acute exposure to provocative agents such as the endotoxin lipopolysaccharide (LPS) and mineral dusts including silica. Studies were also carried out in the presence of specific cyclooxygenase inhibitors. The addition of LPS (10 µg/ml) to the culture medium produced a significant increase in PAM release of the eicosanoids: PGE2 (3.5 fold over baseline), TXB2 (2.8 fold over baseline) and LTB4 (4 fold over baseline). LPS also elicited a 2.5 fold elevation in IL-1 from these cells and a 9 fold increase in TNF release. The cyclooxygenase inhibitor, ibuprofen, significantly inhibited the LPS-induced rise in PGE2, TXB2 and TNF but had only a modest suppressive effect on IL-1 release. Exposure of these cells to silica dust elicited a similar augmentation in eicosanoid and cylokine release which was neutralized by prior exposure of the cells to ibuprofen. These results suggest that the enhanced production of eicosanoids and cytokines by PAM exposed to endotoxins and/or mineral dusts may be linked and that inhibition of eicosanoid release is linked to the production of TNF. IL-1 release however is not effectively neutralized by cyclooxygenase inhibition.INTRODUCTIONThe initial pulmonary cellular response to inhaled mineral dust involves the elaboration of potent inflammatory mediators from the pulmonary alveolar macrophage (1). These mediators include the eicosanoids (oxygenated metabolites of arachidonic acid) and cytokines (intercellular peptides) which are released into the alveolar space by the interaction of mineral dust with the PAM surface membrane. The eicosanoids and cytokines promote local nonvascular and vascular smooth muscle contractility changes, elicit the recruitment of additional mononuclear cells into the alveolar space, and enhance the activation, growth and differentiation of lung fibroblasts (2). In this study we sought to examine whether eicosanoid release and metabolism are linked to cytokine release when PAM are activated upon exposure to endotoxin or mineral dusts. Modulation of these pathways through inhibitory pharmaceutical agents may help attenuate the Injurious effects caused by a sustained release of these proinftammatory intercellular factors (3). To that end, we have studied the in vitro effects of endotoxin and silica on eicosanoid and cytokine release from cultured PAM obtained from healthy human volunteers."

Mar 1, 1992

By E. D. Gardner

An explosion occurred in a high-pressure compressed-air line in October, 1930, at an Arizona copper mine. The explosion was unusual, and nothing had teor. noted by the plant operators to indicate the possibility of such an occurrence. It is necessar The air is The mining company uses compressed-air locomotives to haul about 4,500 tons of ore per day from the stopos to the pockets at two hoisting shafts. The ore cars hold five tons each, and are pulled in trains of 30 cars. to charge the locomotive with compressed air at both ends of the trip. conveyed from the compressors at the surface to the distributing points unier roun in special high-pressure four inch steel pipe that was tested to withstand 2500 pounds per square inch before being installed. The air is delivered to the loco- motives at a pressure of 1000 pounds per square inch. There are no receivers in the system. The air for running the locomotives is compressed by one three-stage and two four-stage compressors which have capacities of 600 and 300 cubic feet per minute, respectively. These machines are operated by electric power, and are in an end of the main compressor building in which air is compressed to supply the air drills in the mine. Whenever the demand decreases, as at the noon hour, one or more of the Compressors are shut down. On this particular occasion, at the end of the noon hour, one of the operators was approaching the high-pressure compressors to start the two smaller machines that were not running, when the explosion took place under the floor a few fost ahead of him. The man was mocked down and received some superficial cuts and bruises, but was not seriously injured. The floor was torn , the side of the building blown out, and holes imo cited in the roof some twenty feet above. The explosion was immediately followed by a fire which was quickly put out by the plant operators with hand fire extinguishers. At the time of the explosion the 600 cubic foot compressor was running alone, and the pressure in the system at the machine registered 1040 pounds por square inch. On examination it was found that two 6-fout sections of pipe, about tan feet apart, were completely ruptured into twisted fragments; the rest of the pipe line, apparently, was not injured. The destroyed sections were in that part of the pipe near the large compressor and above the connection from the two smaller machines. It is not definitely mom what caused the explosion. Explosions in other compressed-air systems have taken place, and, although of rare occurrence, have caused loss of life. Such explosions are not confined to high-pressure installations and several have occurred at plants compressing air te one hundred pounds per square inch, or less. plosions of this nature are not to be confused with the rupturing of compressor cylinders from excessive air pressure caused by the discharge valve being closed.

Feb 1, 1921

By Samuel B. Flagg

The Bureau of Mines is endeavoring to ascertain how mineral fuels in which the Government has a direct interest, by ownership or use, can be utilized with highest efficiency. For this reason the bureau has been, and is, carrying on investigations to ascertain the condi- tions of furnace construction and management that are necessary to insure the smokeless combustion of the different coals that are found in public lands or are purchased for Government ships and power plants. Another reason for the bureau undertaking these investigations is the need of better furnace management and a more careful selec- tion of fuel at many Government plants. There are Federal build- ings in hundreds of cities. The coals available at many of these cities differ greatly in quality, and the furnaces in some of the Fed- eral buildings were not designed for efficient utilization of the cheap- est available coal. Hence, some of the boiler plants smoke badly unless fed with low-volatile coal and have caused repeated com- plaints not only from neighboring property owners who have suffered damage, but from persons endeavoring to create a civic pride in clear air. In the course of its fuel investigations the bureau has noted the conditions governing fuel consumption in different cities and has studied the attempts made by these cities to abate smoke through the passage of ordinances imposing penalties on smoky stacks. Some results of that study are presented in this report. The most im- portant conclusion reached is that smoke abatement by ordinance can not hope to succeed unless supported by public sentiment and that a smoke ordinance should look to future prevention rather than to immediate prohibition. In other words, strict control of furnace construction offers much greater hope for smoke abatement than desultory imposition of severe penalties on the escape of "dense" or "black" smoke.

Jan 1, 1912

By H. Schultz

Urban refuse that was mechanically separated at the U S Bureau of Mines pilot plant in College Park, Md., was successfully evaluated for its fuel values using standard coal analysis methods. Analyses performed on refuse samples taken from five sample points included moisture, ash, sulfur, chlorine, and heating value. It was recommended that characterization of the combustible portion of urban refuse by standard coal analysis procedures should be widely adopted.

Jan 1, 1975

Reduce the hazards to which mine personnel are exposed by providing safer procedures for removing dragline wire rope terminations. Background The termination points of wire ropes used on draglines consist of a wedge and socket that lock the rope in place through friction. These components must be separated when the wire rope is changed. At present, the cannon method is the most common procedure used to accomplish this. However this method, using a small cannon and primer (detonator) cord to propel a steel projectile that will knock the wedge out of the socket, has the potential of causing injuries to mine personnel and damage to equipment. The Bureau of Mines, has devised safer, and equally efficient methods of removing wire rope terminations. The Bureau began by studying the cannon method, its merits and draw-backs. Safety guidelines were then developed for the cannon method, and two alternative methods-the pendulum ram and hydraulic pusher-were devised and tested. The Cannon Method The steel projectile used to separate the wedge and socket in the cannon method was found to be very effective. However, the method poses the inherent hazards of any explosive de-vice-hazards that could be increased by lax work procedures. There is no strict uniformity in the manufacture of the cannon or in the work procedures used in the mines employing it. Hazards could be reduced, or even eliminated, with adaption of certain manufacturing and work-procedure guidelines, such as 1) making the cannon and projectile de-signs, as well the work procedures used, uniform, 2) ensuring separate loading of the charge and detonator with insertion of the detonator through a separate port, 3) connecting electrical firing circuits only after the charge and projectile are loaded and the cannon is placed in its final firing position, 4) using approved detonating devices, 5) anchoring the cannon before firing and, 6) placing armor netting over the cannon before detonation.

Jan 1, 1986

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By T. O. Llewellyn

Laboratory batch and semicontinuous studies showed the feasibility of using methylene bromide and trichloroethylene in heavy liquid cyclone concentration of a Nevada brucite ore. Cyclone tests of minus 20- plus 200-mesh material at specific gravities of 2.42 and 2.44 recovered 71.6 to 74.9 percent of the MgO at grades of 95.5 and 95.4, respectively. Neither increasing the feed pulp density from 5 to 25 percent solids, nor varying feed pressures from 25 to 60 psig had any apparent effect on the heavy liquid separation.

Jan 1, 1971

Monitoring systems can have numerous uses in the mine. They can aid in the efficient management of the mine by providing environmental trend data, production and maintenance control, and communications. In some cases, they can provide justification to petition the Mine Safety and Health Administration (MSHA) fog a variance of one of the mandatory safety standards. They may also increase the gross revenues of the mine by increasing the amount of coal produced or increase profits by reducing the cost of producing that coal. No single system will satisfy the requirement of all mines. Some may require simple hard-wired status-reporting systems; others, multipurpose computer-based systems that collect, analyze, and store data and perhaps control some mine functions. Even though systems vary in complexity, they are all composed of three functional components. The first component is sensors that measure the environmental or production parameters and produce an electrical signal that is fed into the telemetry. The second is telemetry devices that receive the signal from the sensors and transmit it in either analog or digital format to the third com¬ponent, analysis and display equipment. This equipment receives the transmitted signal and either stores it for later analysis or displays it. The analysis-display equipment ranges from simple strip chart recorders with preset alarms to computers, cathode-ray tubes (CRT's), and line printers that can also provide production reports. 4.2 Uses of a Mine Monitoring System A list of potential uses for mine monitoring systems, including both production-related functions and those related to health and safety, was used to develop a questionnaire. It was presented to representatives of the mining community to determine their current monitoring priorities. The responses indicated that the industry's priorities fall into the following two categories: First priority- Production and haulage Maintenance Second priority- Ventilation Communication Fire monitoring Personnel The survey shows that production-oriented systems were the most appealing to the questionnaire respondents. Since even small improvements in production efficiency and maintenance can have a large financial impact, the desirability of monitoring systems that focus on these areas is understandable. The results are summarized in table 4-1. The function that scored 100 was viewed as the most beneficial monitoring function.

Jan 1, 1984

1. In 2003, a total of 258 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining sector, comprising 1.8% of all mining operations.1 • Gold mines comprised 44.2% (n = 114) of all metal mining operations. Other common types of metal mines were iron ore (n = 29; 11.2%), copper ore (n = 28; 10.9%), and lead and/or zinc ore (n = 21; 8.1%). • Nevada had the largest number of metal mines (n = 48; 18.6%) followed by Alaska (n = 29; 11.2%).

Feb 1, 2005