Search Documents

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for coal preparation plants by state during 1990-1999. Table 28 also shows the risk rates, employees' working hours, and lost workdays by state. For coal preparation plants, 91 fires occurred in 1 1 states during 1990- 1999. Twenty-three of those fires caused 25 injuries (the yearly average was 9.1 fires and 2.5 injuries). Ten fires and eight injuries involved contractors. The Ewhr value was 24 1 x 10' hr (Irr = 0.02 l), and the LWD value was 198. Pennsylvania had the most fires (24 fires and 4 injuries), whereas West Virginia (22 fires and 7 injuries) and Kentucky (22 fires and 7 injuries) had the most fire injuries. Among these states, Kentucky had the highest injury risk rate value (Irr = 0.025). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the periods (an increase is seen only during the last period). The number of fire injuries show a decrease followed by an increase during the periods, accompanied by a decline in employees' working hours throughout the periods. The Irr values follow patterns similar to those shown by the injury values (see table 29 and figure 11). Tables 30-35 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 12 shows the major variables during 1990-1999. Table 36 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

By M. R. Geer, H. F. Yancey

"INTRODUCTION The increased use of coal as pulverized fuel has focused attention on the grindability of coal and on the necessity of evaluating this property by a method suitable for use in the usual coal-testing laboratory. Without some knowledge of how various coals behave in the grinding operation, that is, how their use affects mill capacity and power requirements, the selection of coals for pulverized-fuel plants cannot be made on the same critical basis used in selecting coals for other types of burning equipment. The grindability of a coal, serves principally as an indication of the mill capacity attainable in grinding it - not as a direct index of the total cost of grinding. Although the grindability of coal may play a minor role at some plants, it is a decidedly important factor where pulverizer capacity limits the ability to carry high loads.Purpose Standardized tests for determining the grindability of coal are relatively new, so that the information now available on the grindability of various coals is limited in comparison, for example, with that available on proximate analyses. Published information is restricted to determinations on many important Eastern coals by the Fuel Engineering Co. of New York, 4/ a bulletin giving the results of numerous tests by the Babcock and Wilcox Co. 5/, and a comprehensive report on. Alabama coals by the Bureau of Mines. 6/This report presents the results of grindability tests of 34 samples of coals from Illinois, Kentucky, Pennsylvania, Utah, Virginia, Washington, West Virginia, and British Columbia at the Northwest Experiment Station of the Bureau of Mines, Seattle, Wash., in cooperation with the College of Mines of the University of Washington. In the future, as the laboratories of the Bureau make grindalility tests of other coals, additional reports will be issued."

Jul 1, 1938

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

By Laurance L. Oden

The Bureau of Mines studied three processes for preparing NaAl(OH)2C03) the intermediate compound which is calcined to produce alkalized alumina: (1) Mixing of Na2 C03 and of A12 (S04)3 solutions, (2) digestion of aluminum hydroxide in solutions of Na2C03 and NaHC03 at 90° C, and (3) addition of CO2 at 25° C to caustic solutions of aluminum to precipitate aluminum hydroxide followed by digestion at 90° C. The first process had the highest raw material consumption and washing requirements, and successful application of process 2 depended upon the availability of active aluminum hydroxide. Process 3 was the most effective, considering both process technology and raw material requirements. Procedures were also investigated for washing, filtering, drying, and calcining precipitates. Analytical methods included X-ray diffraction, atomic absorption spectroscopy, differential thermal analysis, and thermogravimetric analysis.

Jan 1, 1969

By F. D. Osgood, A. C. Fieldner, W. A. Selvig

In connection with investigations being conducted by the Bureau of Mines regarding pulmonary disease which is prevalent among metal miners in certain districts , a large number of rock- dust samples have been collected , and have been examined in the Bureau's laboratories . The earlier work has been described in Bureau of Mines Technical Paper 105 , " Pulmonary disease among miners in the Joplin district , Missouri , and its relation to rock dust in mines " by A. J. Lanza and Edwin Higgins , 1915 , and in Bureau of Mines Bulletin 132 , " Siliceous dust in relation to pulmonary disease among miners in the Joplin district , Missouri , " by Edwin Higgins , A.J. Lanza , F.B.Laney , and Geo . S. Rice , 1919. The methods of collecting and examining dust samples have been greatly improved during the investigation , much valuable information having been made available by similar investigations conducted by the Miners ! Phthisis Prevention Committee , Union of South Africa . The latter are described in the " General report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1916 " , and " Final report of the Miners ' Phthisis Prevention Committee , Johannesburg, Union of South Africa , 1919. " The investigations by the Bureau of Mines and the South African committee show that by prolonged inhalation of air containing minute particles of sharp and insoluble rock dust , the lungs retain sufficient dust particles to cause decided injury to the lung tissue , the injured lung becoming very susceptible to the development of tuberculosis .

May 1, 1920

By J. B. Zadra, S. M. Shelton, M. M. Fine

"Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade ore in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that woo set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3606, Manganese Investigations. 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By Lisa Steiner

Almost every process has a predecessor, and studying the predecessor helps to define needs and shortcomings to be addressed in the new design. It also suggests what information is needed by the users in order for them to be able to operate safely and effectively. The end users of a system can provide important feedback to better evaluate the current and proposed designs. When new technology is introduced into a system, mishaps may occur before it is realized that human-system interactions were not considered adequately in the design process. A systematic methodology to evaluate the causes of these injuries and to develop remedial recommendations can enhance safety. This paper illustrates how such an approach was used to assess remote machine operation in underground coal mines. The dynamic work environment of underground mining with its unpredictable geologic anomalies can result in numerous hazards. Many of these hazards, including mine roof collapse, occur near the working face where coal is being extracted. The face area is also where the most intricate interactions of people and equipment occur. For these reasons, a high priority has been placed upon minimizing hazards to the workers at the face. A remote control operation was introduced to provide a safer working distance from these hazards. As the remote control technology began to be widely used for extended cut mining operations, new issues became evident. It was essential to develop mechanisms for mines to evaluate these issues in order to predict and reduce injuries. Mining methods and equipment changes must allow for the ability of workers to adapt to changes in their dynamic mining environment. Consideration should be given to how the worker will use familiar information to make decisions in now unfamiliar situations. There will be both intended and unintended consequences [Merton, 1949]. Designers try to anticipate and eliminate surprises, but it is impossible to eliminate them all. How, then, will the new system affect the tasks to workers which are currently accustomed? As suggested below, this question may be addressed and more of the unintended outcomes predicted with a planned design process which includes strong human factors input to determine interactions and behaviors of participants.

Jan 1, 2005

By D. J. Parker

Since the introduction of electricity into the mines of the United States , the hazards incident to the industry have increased materially in both coal and metal mines . For economic reasons the tendency at present , particularly in coal mining , is decidedly toward the adoption of electrical mine machinery , including alternating current machinery , on a more extensive scale than ever before . Obviously, the growing use of such equipment will result in an ever -increasing number of underground transformer stations . The principal electrical hazards in mines are threefold ; fire , explosion, and contact . Of these , fire is the greatest hazard involved in the use of electricity underground , and several fires have originated in underground transformer and motor generator set stations . The fire hazard due to improperly installed and poorly maintained underground transformer stations is an ever-present one , and failure to take the necessariman remedial action is likely to result , sooner or later, in the destruction of life and property . Upon suggesting the necessary corrective measures with respect to such installations , one is often confronted with the statement to the effect that even though this particular hazard has existed over a period of years , there have been no unfavorable results therefrom thus far . Frequently , the desirability for action is not apparent to the mine management until it is too late . Because a mine has a record free from fires , explosions , etc. , over a number of years of operation during which these hazards existed , such good fortune should not be taken as a guarantee that this or any other mine is immune from these common dangers . When the elements of an existing hazard are properly balanced or in the right proportion, the unfortunate combination must of necessity culminate in misfortune of one kind or another. The fire hazard due to underground transformer installations can be very definitely minimized by proper installation and maintenance . In coal mines the transformer banks , connected to 2,300 and occasionally to 4,400 volt circuits , are often found located in open- ended crosscuts , mounted on concrete or timber foundations , and in nonfireproof surroundings .

Jul 1, 1930

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton's method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

By John J. Henn

An evaluation is presented for an ammonium sulfate leaching process designed to extract manganese from Cuyuna, Minn., and Aroostook, Maine, deposits. In this process the manganese and iron in the ore are reduced to MnO and Fe 3 0 4 in a shaft furnace; the reduced ore is then leached with ammonium sulfate solution forming soluble manganous sulfate while leaving most of the iron undissolved. After filtration, the manganese and some impurities are precipitated from solution as carbonates which are then pelletized and calcined to form a product composed mainly of Mn3O4. The plants are designed to produce 100 tons per day of manganese contained in a product that is suitable for the production of ferromanganese. A byproduct credit, together with the extra processing cost, is included for the Cuyuna ore processing plants because Fe2O3 may be recovered for use in blast furnaces. The estimated operating costs per ton of manganese, excluding income taxes and return on investment, are: [ ] The process with or without byproduct recovery, when treating Cuyuna or Aroostook ores, is not economically competitive with ores available at $71.43 per ton of contained manganese.

Jan 1, 1968

By John A. Organiscak

Laboratory and underground studies were conducted by the Bureau of Mines to evaluate the effectiveness of a water-powered scrubber and a brattice partition to create a clean split of air for longwall workers at the tailgate. In simulated laboratory tests, the system was very effective in creating a clean split of air. Observed system efficiencies were 74 and 84 pct with induced airflows of approximately 2,000 and 2,500 cfm, respectively. Underground evaluations indicated that the system was capable of reducing respirable dust at the tailgate. The first underground evaluation resulted in protection efficiencies of 30.7 and 42.5 pct at scrubber water pressures of 150 and 450 psig, respectively. A 33.7-pct protection efficiency was observed in the second underground evaluation with a modified partition and the scrubber operating at 250-psig water pressure. To be most effective, the system should have the scrubber operating at a flowrate of 10 gpm at 500 psig to deliver a maximum quantity of cleaned air behind a well-sealed partition.

Jan 1, 1983

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

By W. C. Hudson

"The Miami-West Palm Beach belt of silica sand, which may be suitable for the manufacture of high-grade glass, extends 65 miles northward from the neighborhood of Miami to the vicinity of West Palm Beach, The sand presumably originated in the host rocks constituting the oceanward slope of the Appalachian Mountains and the Piedmont Plateau of Georgia and the Carolinas. The sand now lies in a long, narrow, and probably thin belt that forms a dune-capped terrace marking a previous stage of submergence. The highest dune crests appear to be no more than 30 feet above sea level, and the water table is about 10 or 15 feet below the general level of the terrace.The width of the belt in several places is known to be more than a mile, and the thickness of the clean glass sand sampled ranged from 4 to more than 7 feet. Visual inspection and the meager data indicate the existence of bodies of glass sand large enough to supply foreseeable markets.Analyses of three samples indicate that beneficiation would make the sand suitable for the better grades of ordinary and flint glass.The prospective grade and quantity of sand, an available market in Florida for glassware, and the expectation of postwar expansion of the new industry of glass producing justify more detailed exploratory work and beneficiation testing.U. S. Route No. 1, Old Dixie Highway, the Seaboard Railway, and the Florida East Coast Railway, all substantially parallel and usually within a width of a mile or two, run along parts of the belt or between it and the coast. In addition to many streets and unpaved roads, a paved road crosses the belt at right angles about every 5 miles. Numerous towns are situated within or near the belt. Any area selected for a mining, processing, and manufacturing plant would be near a railroad, a highway, and water and also accessible to public utilities.The subtropical climate, famous for its pleasantly warm winters, would preclude seasonal interruption of plant operations."

Apr 1, 1946

By David C. Oyler, Paul W. Jeran, William P. Diamond

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbecl at a vertical depth of 999 feet, The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a “bird foot” pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By Jr. Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.