Search Documents

By John Nagy

This circular has been prepared for the guidance of safety engineers, shot firers, and coal-mine inspectors concerning multiple blasting with short-delay (millisecond-delay) detonators. These special precautions are suggested in addition to those normally followed in blasting, as outlined in the Federal Mine Safety Codes 5 6/ and in Miners' Circular 58.7/ INTRODUCTION The use of short-delay blasting has been proposed for promoting safety and increasing the rate of production in coal mining. Ideally, short-delay blasting, as compared with equivalent single-shot blasting, reduces exposure of the shot firer to dust, fumes, and weakened roof; as compared with equivalent simultaneous blasting, it reduces roof disturbance.

Jan 1, 1959

By John P. Gooch

Data for the ternary phase diagram for the system 1,1,2,2-tetrabromoethane/water/2-propanol at 25° C have been measured. Experimental methods used are described, and the complete ternary phase diagram is presented. A simple example is given to review the use of the ternary diagram.

Jan 1, 1972

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure'' or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", “canopies” , "roll bars" , protective structures" and other such descriptive names. In this report, "ROPS" describes the function of the structure; "FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection. “MESA” is used as an abbreviation for the Mining Enforcement and Safety Administration; "USBM" is used to abbreviate the U, S. Bureau of Mines.

By Gary L. Mowrey, William D. Monaghan, George F. Persetic, Gregory M. Molinda

Ground penetrating radar (GPR) has been investigated by the U.S. Bureau of Mines Pittsburgh Research Center for its potential to determine rod hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth to determine the value of GPR for roof hazard detection. The resolution of the current systems allows detection of gross roof fractures (>6A mm (>0.25 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologics changes in the roof. Differences in data quality are discussed, as well as suggestion for collecting improved data.

Jan 1, 1996

By Jerry W. Stengel

The Bureau of Mines subjected two manufacturers' chemical oxygen (K02) self-rescue breathing apparatus to a series of laboratory environmental treatments designed to simulate various conditions in underground coal mines. The environmental treatments consisted of extremes of temperature, shock, and vibration. The tests were designed to be used as predictors of the ability of the self-rescuers to survive those environmental insults with no degradation in their protection to the wearer. Based on the severity of the treatments, simulating conditions more severe than offered by the mining environment, the two apparatus tested should be able to withstand the abuse offered by the mining environment and still function as intended in an emergency. Correlation of these tests with results of long-term field evaluations is needed to provide confidence in the laboratory tests as predictors.

Jan 1, 1982

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons, Jay F. Colinet

The importance of controlling respirable dust and methane gas levels in underground coal mining cannot be underestimated. While respirable dust can significantly affect the occupational health of underground coal miners, methane gas accumulations pose significant safety concerns for these same workers. Water sprays and machine mounted dust scrubbers offer effective control of respirable dust exposures and methane gas accumulations. Water must not only be applied carefully to avoid dust rollback to the machine operator but must create sufficient turbulence to remove dead zones that could contain high concentrations of methane gas. While the flooded-bed dust scrubber has been generally responsible for decreased worker exposures to respirable dusts, this device has proved effective in controlling methane levels at the face. This paper reviews practical applications of water sprays and dust scrubbers to control respirable dust and methane gas on continuous miner faces.

Jan 4, 2000

By John G. Kovac

A computer simulation has been developed by the US. Bureau of Mines to estimate the chances of a miner making a successful escape while wearing a self-contained self-rescuer (SCSR). The model takes into account (1) training in the use of SCSR's, (2) apparatus integrity, and (3) oxygen cost of a mine escape. This report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By T. J. Lutz, G. T. Homce

A standard Ford1 4600 agricultural tractor was converted to remote control to perform ASAE/SAE field upset tests (rear rollover and side rollover). This paper discusses the engineering process to develop a remote-controlled tractor in determining the critical parameters of operation, to choosing appropriate actuators, designing the circuitry to control them, installing the actuators on the tractor, testing the system for functionality and then conducting numerous overturn tests. The system uses off-the-shelf components for simplicity, replaceability, and economic concerns. The remote control system has withstood 21 tests to date with no failures and will continue to be used for at least three more years of testing.

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By T. O. Llewellyn

The Bureau of Mines conducted laboratory batch beneficiation tests on a waste granite sludge from New Hampshire to determine the feasibility of recovering a reusable silicon carbide product. The granite sludge responded to attrition scrubbing, desliming, and flotation in either alkaline or acid circuits using fatty acid as a collector. Recovery of over 80 percent of the contained silicon carbide at grades of up to 96 percent SiC was obtained.

Jan 1, 1975

By Edmund S. Leaver, Jesse A. Woolf

"The Baboquivari mining district is about 60 miles southwest of Tucson, Ariz., the present railroad shipping point. The values are silver and gold. The silver is largely associated with the black oxides of manganese. The ore is highly oxidized, and careful panning shows only a very small amount of pyrite. Our sample analyzed as follows:A flotation mill has been installed in the district, but it does not concentrate the precious metals satisfactorily. Our best laboratory flotation results were obtained by grinding to pass 65-mesh and floating with Xanthate or standard flotation oils plus sodium sulphide and polysulphide. This sulphidizing method gave a concentration of 32 per cent of the silver and 80 per cent of the gold, which about equals plant practice.We do not know of an instance where the oxidized forms of manganese have been concentrated satisfactorily by flotation.Plain cyanide on the original ore extracts practically all of the gold but only one-third of the silver. A preliminary deoxidizing roast, using producer gas or powdered coal, gives a calcine from which cyanide dissolves about 90 per cent of the gold and 75 per cent of the silver. This method of treatment, known as the Clevenger-Caron process, is described in Bureau of Mines Bulletin 226.Preliminary treatment with sulphur dioxide by burning pyrite or sulphur and passing this gas into the pulp until all of the contained manganese is dissolved or changed in form best prepares the ore for cyanidation. The acid consumption will vary with the percentage of manganese and other soluble constituents. Neither gold or silver is dissolved by this acid treatment. The washed residue gives maximum cyanide dissolution of the gold and silver with minimum loss of cyanide,"

May 1, 1928

By Doris M. Hyde

Belize remained relatively insulated from the social and political turmoil that affected some of its Central American neighbors. This stability encouraged new foreign investments that assisted the economy, especially in tourism and agriculture. The mineral sector remained limited to construction-oriented materials. Oil exploration efforts continued by the various concessionaires.

Jan 1, 1987

"The Generic Mineral Technology Center on Respirable Dust was established in August 1983, at the request of the Bureau of Mines, to conduct research that affords ""...each miner the opportunity to work underground during the period of (his/her) adult working life without incurring any disability from pneumoconiosis or any other occupational disease"". The Center consists of the Mining and Mineral Resources Research Institutes (MRI) of The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with the MRIs of the Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). (FIGURE 34) Michigan Technological University (MTU) is also affiliated with the Center in the area of diesel particulates.The Center brings together experts concerned with particles causing potentially disabling or fatal diseases including pneumoconiosis (""black-lung""), silicosis, and asbestosis. The latter is of deep concern not just to workers in the mineral sector of the economy but also to the general populace. The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The research program of the Generic Mineral Technology Center explores these scientific, engineering or medical concerns with the objective of refining existing strategies and developing new respirable dust control techniquesand technology that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on five areas (FIGURE 35):"

Nov 1, 1988

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

? A roof bolter reaches for a lever while guiding the drill with his other hand. Since he's watching the drill and many of the controls look and feel alike, he hits the wrong control and crushes his hand. ? Six hours into the night shift, an ore truck driver dozes off. The truck plows over the berm and down into the pit. ? Fleeing a afire, a face crew sees smoke in the intake entry. Assuming the fire is ahead, they cross over to another entry, but soon encounter even worse smoke. These very different accidents have at least one factor in common: the human factor. The actions, decisions, thoughts, or perceptions of one or more humans contributed to the accident. These are just a few examples of safety problems researched by the Human Factors Group of the Pittsburgh Research Center, U.S. Department of Energy.

Jan 1, 1998

By Carlton E. Brown, William P. Yant

"INTRODUCTION Direct visual microscopic determination of particle-size distribution and number concentration of atmospheric dust is time-consuming and trying to the eyes. By using the microscope to project images of the particles at high magnification onto a screen much of the eyestrain can be eliminated and particle-size distribution results obtained with less effort and at a considerable saving in time. It also permits simultaneous observation of the images by more than one person. Microprojection requires no more skill and very little more apparatus than is required in the use of the microscope. Anyone familiar with the microscope should be able to obtain as perfect images on the projection screen as in direct visual microscopy since the same laws and limitationsThe theory and practice of microprojection are described in detail in texts. 5/6/ The procedure has been used and found to be satisfactory for measuring the particle-size distribution of sub-sieve-size substances, such as pigments and powder 7/8/ in the same size range as that of atmospheric dust. The Bureau of Mines has used the microprojector and found it to be quite satisfactory for (1) the determination of the number concentration of atmospheric dust R.I. 3289 in samples collected by the Owens jet dust counter; (2) particle-size distribution in samples of atmospheric dust collected by the Owens jet dust counter and by the electric precipitator; and (3) the particle-size distribution of dusts, blood cells, bacteria, and pollen. Work is in progress at this Bureau on the use of the microprojector in counting impinger samples. The use of different kinds of illumination, such as reflected (dark field), polarized, monochromatic, and ultraviolet, in the projection of images of atmospheric dust particles is being considered."

Oct 1, 1935