Search Documents

By Dennis R. Dolinar, Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mineworkers. Skin failures do not usually involve failure of the support systems, but result from rock or coal spalling from between the support elements. For instance, in 1997 more than 800 miners were injured by roof and rib falls, of which 98% were the result of skin failures [Bauer et al. 1999]. Also, nearly 80% of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and for roof and rib failures is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper reviews the roof and rib accident statistics resulting from skin failure, and highlights the incidences by type, numbers and percentage, in-mine location, supported and unsupported roof, and worker activity at the time of injury. Also discussed are the causes of roof and rib skin failures, current and improved support methods and materials for skin surface control, and machine design modifications for improved roof bolter operator protection. It also reviews the historical literature on skin failures and control methods.

Jan 10, 2000

By W. N. Poundstone, W. M. Merritts, B. A. Light

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining. This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g,.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes. In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased. Tests indicated that methane and water infused in bleeder holes traveled along the bedding planes of the Pittsburgh coalbed at a faster rate than across the planes. Methane associated with coalbeds is produced by the slow decomposition of carbonaceous material in the absence of air and the presence of water. It is lighter than air and, depending on its concentration, forms an inflammable or explosive mixture with air. It is believed that methane is entrapped in and around the pores of the coal and adjacent strata--often under great pressure. In many cases where the strata have been disturbed by geologic movements the

Jan 1, 1962

By J. Douglas Causey

In 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a portion of the 110,000 acre Massacre Rim Wilderness Study Area (CA-020-1013). The area studied, containing 23,260 acres, is located in northwest Washoe County, Nevada, about 25 miles west of Vya adjoining the Charles Sheldon National Wildlife Refuge. Basalt caps older tuffaceous sedimentary rocks in an area that contains no claims or prospects. No mineral resources were identified during this investigation.

Jan 1, 1987

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the charcoals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By David P. Lindroth

The heat content above 25.0° C up to 1,000° C was measured for six rock types: St. Cloud Gray Granodiorite, Holston Limestone, Sioux Quartzite, Rockville Quartz Monzonite, Salem Limestone, and the basalt at Dresser, Wis. The calorimetric data were obtained with an isothermal jacket-copper block calorimeter. The experimental heat content data for each rock type are presented, along with specific heat data obtained from the temperature derivative of the heat content. For the six rock types the maximum deviations of the specific heats at a given temperature were within 10 percent below 575° C and within 34 percent above 5750°C. The increase in the values of specific heat range from a minimum of 13 percent for the basalt at Dresser, Wis. (temperature range, 100° to 1,000° C) to a maximum of 46 percent for Holston Limestone (temperature range, 100° to 870° C).

Jan 1, 1971

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

By E. A. Johnson

As part of its effort to reduce the environmental impact associated with mining and metallurgical operations, the Bureau of Mines used a modified form of the Environmental Protection Agency's Extraction Procedure toxicity test on copper reverberatory slags that contained low, medium, and high levels of the impurity elements As, Pb, Sb, Bi, and Zn. All tests resulted in extracts that did not exceed those limits published in the May 19, 1980, Federal Register; there-fore, these solid wastes were designated as nonhazardous for most landfill disposal situations. However, arsenic and lead levels disturbingly close to the allowable limits--and even higher levels of copper and zinc, for which there are no established limits--leached from the high-impurity-element granulated slags. These slags should be handled in such a way so as to minimize the possibility of water contamination. One baghouse dust was tested according to the EPA procedure and found to exceed the extract limits by a factor of 10. This solid waste may be considered hazardous.

Jan 1, 1982

By J. G. Walters

The method for predicting coke strength developed at Steinkohlenberg-bauverein, Germany, in which experimental parameters are readily determined by small-scale laboratory tests, was found to be applicable to cokes produced from industrially used blends of American coals. Predicted 1-inch ASTM tumbler indices for four industrial blends were found to be in excellent agreement with the experimentally determined values. The laboratory determined prediction parameters include the proximate analysis of the coal the size consist of the coal, and Ruhr dilatometer test data.

Jan 1, 1971

By J. T. May

The Federal Bureau of Mines investigated the extraction of lithium from hectorite-type clay deposits found on the Nevada-Oregon border. Two clay samples were used in the investigation; one contained 0.36 pct Li and the second contained 0.64 pct Li. The purpose of this laboratory-scale research was to determine how these clays responded to different extraction techniques. Extraction techniques investigated were sulfuric acid leach, sulfuric acid bake-water leach, and roast-water leach procedures with cholorides, sulfates, carbonates, and combinations of these reagents. The processing characteristics of the clay samples showed significant variations, and no one technique was effective for both materials. Lithium extractions near 90 pct were achieved during these exploratory studies.

Jan 1, 1980

By L. Garner McDonald

The U.S. Bureau of Mines tangentially impacted potential coal-cutter bit shank materials against sandstone to investigate the potential of the materials to ignite natural gas by a friction-generated hot streak. The shank material samples were mounted in a 24-in, 550-lb flywheel, which was rotated at surface speeds of 400 to 900 sfpm. The sandstone was advanced toward the rotating flywheel at feed rates of 1 mil per impact. The atmosphere mixture was 7 vol pet natural gas in air. Three grades of polycarbonate resin, an ultra-high-molecular weight polyethylene, and a zinc alloy (ZA27) were among the potential materials. None of these materials caused ignition of the methane at any of the three test speeds (400, 600, and 900 sfpm), but the above materials do not have sufficient strength to hold a carbide tip during coal cutting. Of the materials having sufficient strength to hold a carbide tip, three nickel-based alloys proved less likely to cause a natural gas ignition than did iron-based alloys such as 4340 (a commonly used shank material for coal cutters).

Jan 1, 1992

By David E. Siskind

The Bureau of Mines has studied the fracturing produced in the vicinity of large-diameter blastholes in Lithonia granite. Cores were taken from the vicinity of AN-FO production blasts and examined using a total of seven laboratory and field measurement techniques to delineate zones of damage and evaluate the effectiveness of the seven diagnostic tests for fracture-state determination. Laboratory measurements of acoustic pulse velocity, porosity, permeability, compressive strength, and Young's modulus indicated the extent of fracturing with the acoustic techniques providing the best means of distinguishing between fractured and unfractured core. A severely fractured zone was found to extend approximately 25 inches (64 cm) from the center of the 6-l/2-inch blastholes, equivalent to 8 blast-hole radii. A second zone, characterized by a lesser degree of fracturing extended from 25 to 45 inches (64 to 114 cm) or 8-to l4-blasthole radii. Beyond 45 inches (114 cm) the rock was undamaged.

Jan 1, 1974

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By R. V. Ramani

This report, Volume I of the seven-volume Final Report on the U. S. Bureau of Mines research contract no. G0254030 titled Application of a Total System Surface Mine Simulator to Coal Stripping with the Pennsylvania State University provides an executive summary of the purpose and scope, objectives and results of the research. The remaining volumes of the Final Report, listed below, describe in detail model development, input and output documentation and the three case studies. Under the project, an existing surface mine simulator, Open-pit Materials Handling Simulator (OPMHS) was modified and extended for application to surf ace coal mining. In addition, two equipment selection models, and a cost model were also developed. Volume II: OPMHS User's Manual Volume III: Equipment Selection Models Volume IV: Surface Mining Cost Model Volume V: Application of OPMHS to an Illinois Mine Volume VI: Application of OPMHS to a South Eastern Ohio Mine. Volume VIII: Application of OPMHS to a South Western Mine.

Jan 1, 1978

Graduate education is an integral part of the Center's research program. The scope of. work and the duration of each research project is calculated, in part, by taking into consideration the needs of the graduate research program and graduate training. Full development of student involvement, as demonstrated by the research practicum which is offered to qualified senior undergraduates at Penn State University and is designed to acquaint them with research methods and techniques and inform them of the opportunities available in this field. and the fulfillment of graduate program requirements are of the utmost concern. The Pennsylvania State University and West Virginia University have accredited mining engineering curricula and rank among the schools with the largest enrollment in this area in the nation. The number of undergraduate students enrolled in mining engineering at Penn State and West Virginia University account for nearly 20%, of the total undergraduate enrollment in this discipline in schools across the United States. The Pennsylvania State University. West Virginia University, Massachusetts Institute of Technology, University of Minnesota, and Michigan Technological University, have granted a total of thirty-five (35) doctorate and masters degrees which can be directly attributed to research conducted in the Center.' Of these graduates, fifteen(15) have found employment in the mineral sector of the economy, i.e., in private industry, with government agencies, and at various universities, worldwide. In addition, a number of those graduating with masters degrees are currently pursuing a doctorate degree.

Aug 31, 1989

By N. A. C. Smith

During the past, six, years, the Bureau of Mines has made and. published several hundred analyses of typical crude oils and 'has developed a system of interpreting the analyses and of classifying crudes. This system is presented here with. It is apparently equate for classifying crude oils into four main groups and has also been found very convenient in studying the geological relationships between crude oils, and the probable refinery yields of valuable products from them. Crude petroleum is morn to be a very complex substance. An analytical statement of its properties must, therefore, consist of two distinct parts, - first, the report of the results of the determinations made by the analyst in the laboratory, - second, the proper arrangement, classification and interpretation of these results so that the analysis, as a mole, will indicate the meaning- and the relative- importance of the essential characteristics of the oil.

Jan 1, 1927

By Ronald D. Hill, Elmore C. Grim

The United States is richly endowed with mineral resources. However, mineral recovery by its very nature, involves a destructive process, Figures 1 and 2. In the past, mining practices were all too often conducted with the purpose of removing minerals by the simplest and cheapest method possible, without plans for the preservation of land, water, and air, and with too little consideration for the rights of others. A mining company is in business to make a profit, but every company, regardless of the nature of its business, has moral obligations to reduce its undesirable effects on the environment and to safeguard the rights of others. The problem of environmental degradation caused by surface mining is widespread and serious. Minerals in some form occur in each of the 50 States and several States are extensively mined. Data on the acreage disturbed in the United States, by commodity and State are presented in Table 1. Thirty-one States have laws regulating surface mining, (Table 2). Briefly reviewed in Appendix A-1 are the basic provisions of State laws governing surface mining. It can be seen that these laws vary considerably from State to State owing largely to the mining conditions within that State. Of the 24 coal-producing States, only three (Alaska, Arizona, and Utah) do not regulate strip mining. Even the states that are often cited as models of comprehensive regulations still have problems minimizing environmental damages. Uncontrolled surface mining presents a situation as critical to the well-being of the society as any it has ever faced. Many mining activities have imposed huge social costs on the public at large. These costs are long-range and are in the form of stream pollution, floods, landslides, loss of fish and wildlife habitats, unreclaimed land, erosion, and the impairment of natural beauty. In a 1965 Department of Interior study,(1)it was estimated that of the 25,000 miles (1+0,225 kilometers) of contour bench in Appalachia, approximately 1,700 miles (2735 kilometers) are affected by massive landslides. Additionally, 1+800 miles (7723 kilometers) of streams and 29,000 surface acres (11,716 hectares) of impoundments and reservoirs have been seriously affected by coal strip mining operations in the United States.

Jan 1, 1974

By D. L. Boreck

Thick coal seams are common in the Western United States, Many seams are over 50 it thick (some are over 200 ft thick) and are too deep to extract using surface methods. Currently, such deposits are developed using standard "eastern" mining methods which only extract a few feet of total seam thickness, often rendering the remaining coal unminable with current technology. Novel methods that increase thick-seam recovery have been developed and are currently being used in Europe. These methods--high-face single-pass and multislice longwall, longwall caving, and hydraulic mining--have great potential for use in the United States. Successful use of these methods is an objective of the Bureau of Mines. Their use requires, among other things, a full evaluation of geologic features common to thick coals. The objective of this report is to present and summarize those features that will affect the introduction of the methods into thick-seam mines in the Western United States. The geologic elements delineated are three-dimensional configuration of the seam, cleat development, joints and fractures, roof and floor lithology, and faulting.

Jan 1, 1986

By A. L. Service

The four periods of test operation described in Report of Investigations 5219 indicated that planer mining of phosphate rock was feasible. Corrective measures proposed for design deficiencies indicated in test 4 had to be evaluated, however; and, before the attempt to design a prototype production model, it was considered advisable to test the original machine under more severe operating conditions. Planer A was modified, therefore, during the latter half of 1955, and one additional period of experimental operation was conducted in the Anderson mine of the Montana Phosphate Products Company near Garrison, Mont., during the first 4 months of 1956. Test 5 was made in a stope, where the phosphate bed had been offset in a number of places by minor faults. Considerable difficulty was found in negotiating the irregularities caused by these faults, and productionwise the test was not as successful as some of the previous ones. Information obtained, however, was valuable in designing model B.

Jan 1, 1959

By Howard E. Parkinson, John N. Murphy

Abstract-Underground mines are typically extensive labyrinths that employ many people working over an area of many square miles; exten¬sive analysis of mine-communications systems has identified specific problem areas, in particular the excessive times required to locate key personnel underground, the inadequacy of existing phone systems in terms of capacity and privacy, and the inability to communicate with men on the move with wireless communications, as is taken for granted on the surface. A review is presented of the existing systems, the prob¬lem definition, and the various approaches that have been or are being investigated to solve these problems. Manuscript received June 8, 1977; revised August 28, 1977. The authors are with the Industrial Hazards and Communications group, Pittsburgh Mining and Safety Research Center, Bureau of Mines, U.S. Department of the Interior, Pittsburgh, PA 15213.

Aug 28, 1977

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a long-wall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1986