Search Documents

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX B - DEVELOPMENT OF FOAM-CONCRETE SLURRY MINE SEALANT 1. Introduction This appendix describes the results of an experimental development and laboratory evaluation of foam-concrete as a rapid setting, lightweight, self-supporting mine sealant material. Foam concrete, otherwise known as Aerated Concrete, is a form of lightweight concrete whose structure consists of air bubbles held together by a hardened cement mortar. Its principal applications are found in roofing, insulation, shock absorbing, and backfill. The air bubbles in foam concrete are formed either by chemical reaction in the wet, placed mortar, or by introducing a stable foam into the mortar during mixing. The mortar is usually a cement slurry with fine sand or fly ash as filler. Our attention focused on preformed foam concrete, since this is most adaptable to field applications. Equipment is available,* which simultaneously mixes and pumps a slurry of foam concrete. Such a slurry can be produced at a rate of up to 50 yards/hr and has been pumped in a 2-inch-diameter hose 1000-feet horizontally and 250 feet vertically up without significant bubble deterioration. One very attractive feature associated with the use of foam concrete concerns site logistics. Foam concrete can be generated with densities as low as 20 lbs/ft3, and hence the total number of

Jan 1, 1973

By J. H. Maysilles

The Bureau of Mines is examining a variety of low-grade uranium ores because projections indicate that an appreciable percentage of future U.S. uranium production will be derived from resources containing 0.01 to 0.1 percent U308. One possible source is represented by a granitic material from Wyoming; the available samples contained 0.06 and 0.12 percent U308. Tests were conducted to explore the general leaching characteristics of this potential resource. The material responded to both acidic and alkaline leaching techniques. Conventional acid leaching extracted 93 percent of the uranium in 18 hours; the required acid addition was 50 to 100 pounds of H2S04 per ton of ore, and the oxidant addition was 3 pounds of NaCl03 per ton of ore. The acid consumption continues after maximum uranium recovery has been reached; this effect may complicate heap or in situ leaching with acidic solutions. Some variation in reagent requirements was noted between the two ore samples. Conventional carbonate leaching with strong solutions at 85° C extracted 94 percent of the uranium in 24 hours. These granitic materials also showed some response to dilute carbonate solutions, and the results suggest that the material may be chemically amenable to heap or in situ leaching with dilute carbonate solutions.

Jan 1, 1977

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

Maintain good blowing face ventilation while taking deeper cuts with a radio-remote, scrubber-equipped miner. Approach A six week in-mine study of face ventilation effectiveness was made by comparing the existing MSHA-approved blowing curtain setback distance of 25 ft with brattice set back distances of up to 50 ft. Effectiveness was determined by measuring methane levels at the face and in the immediate return. How It Works Blowing ventilation systems are commonly used in mines because the high velocity air stream created by these systems rapidly mixes with and dissipates methane generated during the cutting of coal. A drawback to blowing ventilation is that the work area is placed in return air and this may create dust compliance problems for the shuttle car and mining machine operator. To clean dust from the return a number of mining machine manufacturers supply dust scrubbers built into the machine. Dust-laden air is drawn into ducting at the front of the mining machine's boom and is ducted to a scrubbing unit located on the machine's main frame. The clean air from the scrubber is discharged as a high velocity jet toward the return, generally from the left fender of the mining machine. When taking cuts deeper than 20 to 25 ft with a scrubber-equipped machine, the machine's discharge is in by the mouth of the blowing curtain, creating a concern by mine workers that a loss of air to the face could result. However, Bureau of Mines research found that the push or throw of air toward the return by the scrubber discharge jet allows good face ventilation to be maintained with extended curtain setbacks.

Jan 1, 1984

By Dave P. Cooper, Tim D. Burgess, Dean H. Ambrose

This paper discusses the application of digital human models (DHM) to examine computer generated forces necessary to move specific joysticks by using roof bolter virtual operators to predict the forces experienced on the operator’s upper extremities. Using DHM and simulations of static movements, investigators analyzed predictions of joint moment and joint force effects on virtual operator’s right wrist, elbow and shoulder and compared them to different body dimensions and work postures. This study exemplifies the ease of estimating upper extremity loads on equipment operators using virtual operators and computer models of equipment and work environment. As expected, comparing results of percentage of joint force and moment reduction using the electronic control and of the mechanical control showed that the electronic control had lower joint forces and joint moments over the mechanical control. The average predicted value of the joint moment on the wrist was 1.84 Nm, elbow 7.85 Nm and shoulder 14.55 Nm and of the joint force on the wrist was 5.06 N, elbow 4.56 N, and shoulder 3.67 N. Because the data illustrates low-level forces to move a joystick, inadvertent actuation of the control is addressed. Regardless of the findings, research is still needed on joysticks in real world situations such as an epidemiological assessment of equipment operators in the field before final recommendations and conclusions can be drawn.

Jan 1, 2007

By J. C. Edwards, C. C. Hwang

In the design for a fire or smoke emergency, a main concern is maintaining an evacuation path that is free of smoke and hot gases. In ventilated tunnel fires, smoke and hot gases may form a layer near the ceiling and flow in the direction opposite to the ventilation stream. The existence of the reverse stratified flow has an important bearing on fire fighting and evacuation of underground mine roadways, tunnels, and building corridors. In the present study, a computational fluid dynamics (CFD) program is used as a design tool to model floor-level fires in a ventilated tunnel. The fire is simulated by a diffusion flame of propane issuing from a circular hole on the tunnel floor. The computed profiles of velocity and temperature along channel cross sections are similar to those obtained experimentally. The computed reverse-flow layer length has been correlated with a densimatric Froude number with some success. A non-dimensional parameter involving the source fire intensity is also used for the correlation. These analyses show that an appropriate ventilation air current must be maintained to provide an evacuation path from the source fire clear of smoke and hot gases. It is believed that CFD modeling, employed correctly and interpreted carefully, can be a useful design tool for fire protection.

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

Identify specific sources and the relative levels of contribution of various components of longwall shearer operations to the total airborne respirable dust generated during mining. Approach A research investigation was conducted in two phases by the Bureau of Mines at five mine sites to identify specific dust sources and their relative importance during long-wall shearing operations. During phase I of the project the specific longwall mining elements identified for evaluation were: cutting, sumping, tramming, conveying, and moving roof supports. During phase II of the project, two dust sources were evaluated: clearance ring cutters cutting in six-inch web width increments, and loading operations. Investigation Results As a result of dust measurements, the gage cutters were determined to be the major dust-generating source on the shearer. These cutters, at 6-inch web depth, produce three times as much dust per unit volume as is produced at 30 inches full web depth. The following list of averaged values for the mines tested shows that shearer cutting generated averaged dust levels four times as high as those generated by conveying, and approximately five times as high as those generated in moving roof supports.

Jan 1, 1984

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

Data or input files are used to describe the mine's ventilation system and physical characteristics necessary for ventilation calculations as well as the physical or mechanical disturbance to be modeled and simulated Data files are organized into lines of categories or groups of information Each line contains multiple sets of information or data items Data lines are read by the program, and the data items provide information to the program variables The data file is in American Standard Code for Informa¬tion Interchange (ASCII) format, sometimes called a DOS text format Creation or modification of a data file is accomplished with text editor software Most word pro¬cessors are also capable of making the required ASCII type files A sample data file and its associated output are included in appendix B. When selecting software for editing the data files, the user should be aware that the software will also be used for viewing the output of the simulation The output file can be quite large (several megabytes), if a lengthy simulation is performed The output can be sent to a printer for a hardcopy fisting, however, the user should also be aware that most printers currently used with PC's print at rates of 100 to 300 characters per second and large output files may take several hours to print Viewing the output with a text editor can save much time and paper DATA FILE MANAGEMENT The data files describing the event and mine to be simulated can reside either on a floppy disk or in a directory on the hard disk drive When the program starts, the user is prompted for the data file location and name The user response is in the form of a standard DOS path and file name For example, if the data file is on a floppy disk located in drive B and the disk has a directory MYMINE with the data file MYDATA DAT in that directory, then, at the prompt

Jan 1, 1990

Provide mine operators with a quick means of identifying the effect of cutting system changes on relative dustiness at the mine face, by developing an interactive computer program for drum-type coal mining machines. Approach A program which simultaneously evaluates machine parameters, coal seam parameters and mine operator-controlled parameters for their effects on relative dustiness has been developed for use on any minicomputer using BASIC computer language. How it works The interactive computer program allows mine operators to make one or more changes at a time to their cutting system to determine how these changes affect relative dustiness of the face. Using this program, mine operators can find the optimum cutting system configuration to minimize dust using their seam conditions and their equipment specifications. The mining machine variables include: number of vane bits, number of gage bits, number of starts, vane wrap, number of end ring lines, rpm, advance rate, ton/min, percentage of time spent cutting per shift, and airflow.

Jan 1, 1986

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

Utilize innovative processing technology to prepare high-purity, ultrafine advanced ceramic powders with little or no contamination occurring during the milling process. Advanced ceramic materials made from these powders could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. Approach Modify and evaluate the Bureau's turbomill, developed earlier to grind a variety of ceramic raw materials (clay, mica, and talc), as a milling or size-reduction technique for hard and abrasive advanced ceramic powders, such as silicon carbide. Background Powders for producing ceramic materials, such as silicon carbide. silicon nitride, alumina, and zirconia, which arc being considered for use in severe applications requiring high-temperature and/or corrosion resistance, are very difficult to reduce to fine sizes for processing into finished parts. Traditional techniques of particle size reduction, such as ball milling and jet milling, are very energy intensive and/or slow. These traditional techniques often produce materials that have a nonuniform particle size distribution and are contaminated by the milling media or container.

Jan 1, 1989

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By Hon-Chung Ko

This Bureau of Mines report provides the enthalpies of formation of cupric bromide and cuprous bromide as determined by hydrochloric and hydro-bromic acid solution calorimetry. At 298.15 K, the values are -33.10 ± 0.4 kcal/mole for CuBr2, and -25.24 ± 0.25 kcal/mole for CuBr.

Jan 1, 1975

Provide the U.S. mining industry with the means to measure and control exhaust emissions of diesel engines used in underground mines. Approach Diesel research is divided into four primary areas: exhaust aerosol measurement, particulate control, gaseous emission control, and chemical and biological characterizition of particulate matter. Diesel research is frequently cosponsored by industry; collaborative research ventures between industry, academia, other government agencies, and the Bureau arc common. Diesel research at the Bureau is conducted in the diesel engine research facility at the Bureau?s Twin Cities Research Center (TCRC). This facility is a state-of-the-art laboratory capable of performing emissions testing, exhaust control evaluations, and safety tests. Background Exposure of mine workers to airborne contaminants from diesel engine exhaust is potentially harmful. The National Institute for Occupational Safety and Health has recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen" and that ?reductions in exposure to diesel exhaust in the workplace would reduce the risk." The U.S. Mine Safely and Health Administration (MSHA) convened an Advisory Committee on Standards and Regulations for Diesel-Powered Equipment and is beginning to implement its recommendations, which cover health, safety, and certification and approval issues surrounding the use of diesels underground. In January 1992, MSHA published an advance notice of proposed rulemaking to regulate diesel particulate matter in underground mines.

Jan 1, 1992

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982

By George H. Ashley

Character The bituminous coals of Pennsylvania range from low volatile to high volatile, but are all low moisture coals The coals are of three types caking of coking, noncaking or splint, and cannel The percentage of volatile matter in all kinds changes from low at the east to high at the west This change is thought to be due to the pies sure and folding to which the coals along with the other rocks have been subjected In the Broad Top field, and in Somerset, Cambric, Clearfield, Centre, and other counties to the northeast, most coals contain from 3 to 5 times as much fixed carbon as volatile matter, the fixed carbon ranging from 67 to 75 per cent, and the volatile mattes from 16 to 24 per cent These coals are classed as lovol coals In the line of counties just west of those listed the coals are of the medium volatile class (midvols) This includes the famous Connellsville coking coal Still farther west, covering most of Washing ton and Westmoreland counties, and the counties to the north of them are high volatile coals of gas coals (hivols) This is discussed in Part I on the geology of the coals of Pennsylvania, where is given in isocaib map Cannel coals ale found in many par is of the bituminous coal field of Pennsylvania, but in particular in Beaver Butler, Armstrong, Indiana, and Clear field counties The cannels of Beaver and Butler. counties are typical high volatile cannels, many of which have been used in times past for oil distillation The cannels of Armstrong and Indiana counties are medium volatile cannels, and while main taming the physical character of cannels, have no more volatile neat ten than the coals around them The cannels of Clearfield County tie low volatile Splint coals of noncakmg coals are not abundant in Pennsylvania. The Sharon coal, formerly mined in Mercer County, was a noncaking or splint or block coal, and was formerly used in the raw state in non smelting Uses STEAM COAL Practically all of the coals of Pennsylvania are steam coals, though many coals in the Commonwealth, because of high ash, are not good steam coals The coal of the Pittsburgh district has long been famous

Jan 1, 1928

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

By Murali M. Gadde, John A. Rusnak

Rock mass classification systems are extremely useful for site characterization and have been employed by the rock mechanics community for several decades. While empirical in nature, the classification systems provide a viable means to quantify the nature of rock mass, which is necessary for stability analyses. In U.S. coal mines, the Coal Mine Roof Rating (CMRR) is the most widely used classification system for several purposes, including sup-port selection, chain pillar design, assessing the stability of extended face cuts, etc. The Analysis of Roof Bolt Systems (ARBS) is an empirical method developed from the CMRR to guide selection of roof bolts as the primary support system in U.S. coal mines. In this paper, the experience of Peabody Energy in applying ARBS to sup-port design is discussed. In general, data from the Peabody mines show that ARBS predictions match well with field conditions. Peabody, however, does not use ARBS as the stand-alone methodology for support selection. Peabody uses a two-pronged approach in which the support requirement is initially estimated from the classification method, and then numerical modeling is used to select the proper reinforcement system. Such an integrated approach is necessary, as ARBS suggests only the “amount of steel” that may be used to support the roof and does not specify which type of roof bolt to use. A case study is used to demonstrate the usefulness of ARBS and Peabody’s integrated approach to support design. Also, the application of ARBS at several Peabody mines showed a very good correlation with support cost. The correlation indicated a direct relation between bolting cost and the ARBS value.

Jan 5, 2007