Search Documents

By L. A. Johnson

The Bureau of Mines analyzed three cores from the south Seep Ridge area of the P. R. Spring tar sand deposit of northeastern Utah. Four tar sand zones are indicated in the area. The zones range in average thickness from 13 to 24 ft. The total net thickness of the tar sand in the three coreholes ranges from 71 to 112 ft. The tar sand occurs between the depths of 27 and 254 ft. It has good porosity, 25.6 pct of bulk volume; high permeability before and after oil extraction, 819 and 2,218 md, respectively; but a relatively low oil saturation, 36.5 pct of pore volume. Gravity of the oil ranges from 8.20 to 16.5° API.

Jan 1, 1975

Detemine the elastic properties and structural integrity of a rock mass in situ. Approach An acoustic device that transmits and receives high-frequency seismic waves between boreholes was designed, built, and field tested. How It Works The acoustic cross-borehole apparatus operates by sending a seismic wave from a transmitter in one borehole to a receiver in a second bore? hole which may be located as far as fifty feet away, depending on the wave transmission quality of the rock. By measuring the wave's travel time and the distance between boreholes, the acoustic velocity of the rock mass can be determined. Characteristics of the seismic wave arriving at the receiver (such as the wave velocity, amplitude, and frequency content) are related to the physical properties of the geologic media, as calcu-

Jan 1, 1982

By Travis Q. Lyday

Fiji has been an independent country within the British Commonwealth of Nations since 1970. It consists of an archipelago of more than 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets, to the larger mountainous islands of Kandavu, Taveuni, Vanua Levu, and Viti Levu of volcanic origin. The islands of Fiji straddle the 1800 meridian about 1,800 kilometers south of the Equator in the part of the southern Pacific Ocean known as Melanesia. The production of gold and silver from the Emperor Mine at Vatukoula on the island of Viti Levu, the main island of Fiji, remained Fiji's only metallic mineral producer. Mining began at the Vatukoula site in 1933, producing 124 million troy ounces of gold and 147 thousand troy ounces of silver by yearend 1985.

Jan 1, 1987

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

By T. M. Klemetti, G. M. Molinda, D. M. Pappas

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

Identity the difficulties of establishing vegetation on mining-related wastes resulting from adverse chemical, physical, and biological properties; describe the ecological and soil factors affecting the relationship between mycorrhizal fungi (soil microorganisms) and plants; and evaluate the feasibility of establishing vegetation on mine waste by introducing mycorrhizae. Problems in Revegetation Successfully using vegetation to stabilize a situ disturbed by mining-related activities depends on knowing the chemical, physical, and biological characteristics of the site prior to, or at the time of, stabilization. The primary objectives of mine land reclamation are to minimize environmental degradation and to facilitate the re-establishment of a functional plant-soil system. Mining disturbances can significantly alter the physical, chem¬ical, and biological characteristic of a site, thus affecting plant establishment, survival, and growth. The physical disturbance caused by the removal and replacement of soil and overburden, together with the waste material from ore processing, affect the chemical, physical, and biological process within the disturbed soil or waste. Additionally, variability in soil properties results from differences in climate, topography, vegetation, and parent material of the site.

Jan 1, 1993

By Kenneth L. Cashdollar

While underground coal technology has progressed over time, regulations on coal dust have not kept up ? the most recent rules are more than 80 years old. The National Institute for Occupational Safety and Health and the Mine Safety and Health Administration conducted a joint survey recently on coal particle ranges as measured in US coal mine samples. In underground coal mines, dust explosions are prevented by the addition of enough rock dust (usually limestone) to make the total dust mixture inert. The rock dust acts as a heat sink for the dispersed dust mixture by reducing the temperature below the value needed to propagate an explosion. Federal regulations require 65% in combustible content in intake airways and 80% incombustible content in return airways, where the coal dust is assumed to be finer in size. The regulations also require an additional 1% incombustible for each 0.1% methane in the ventilating air in intakes and 0.4% additional incombustible for each 0.1% methane in returns.

Jan 1, 2008

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

By J. M. Stuve

The standard heats of formation (?Hf°) of holmium trichloride and terbium trichloride were measured by solution calorimetry. Heats of solution of holmium and terbium metals and their anhydrous chlorides were measured in 4.360 molal HCI at 298.15° K. From these measurements ?Hf° for HoC13 (c) was calculated as -240,290 ±1,700 cal/mo1e, and ?Hf° for TbC13 (c) was calculated as -238,330 ±1,500 cal/mole at 298.15° K.

Jan 1, 1967

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

Provide exhaust face ventilation to remotely-controlled continuous mining machines making extended advances without exposing workers to unsupported roof. Approach Modify the sprayfan to move additional air to and from the coal mine face. Unmodified, sprayfans are capable of ventilating the face with 20-foot brattice setbacks. Additional sprays on the rear of the mining machine allow setbacks to be extended up to 40 feet.

Jan 1, 1988

Continuously monitor air-borne radon daughters that are a hazard to underground miners. Approach A beta detector continuously counts beta activity collected on a filter paper to allow calculation of exposure in working level units. How It Works At each Site a constant flow pump draws mine air through a fiberglass filter located in front of a beta detector (pancake type Geiger Mueller tube), Radioactive particles (products of the radon 222 gas emanating from the mine walls) collect on the filter and decay, releasing alpha and beta particles as well as gamma rays. A portion of the beta particles penetrate the Geiger tube window and create electrical pulses in the tube. These pulses are then amplified and sent by a coaxial type or shielded electrical cable to a central monitor located some distance from a working level detector. At the central monitor incoming Signals are amplified and fed into two channels, (See the block

Jan 1, 1979

By M. C. Chapman, E. C. Westman, A. T. Iannacchione

Examination of seismic records during the time interval of the Sago Mine disaster in 2006 revealed a small amplitude signal possibly associated with an event in the mine. More needs to be understood about the seismicity from mine explosions in order to properly interpret critical seismic information. A seismic monitoring system located at NIOSH’s Lake Lynn Experimental Mine has monitored experimental gas and dust based explosions and impact tests. The seismic signatures from these different events were analyzed using standard waveform analysis procedures. The magnitude of seismic energy during a gas and dust explosion was found to be more dependent on mine entry geometry and seal behavior rather than on the amount of explosive fuel present. The results suggest a large explosion that’s not restricted can generate potentially the same magnitude as a small explosion that is restricted.

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

Lower the respirable dust exposure of longwall shearer operators by keeping the dust cloud confined to the face. Approach Change the location of face-side machine cooling, water sprays. How It Works The dust breathed by the longwall shearer operator is usually produced by the shearer itself. The dust cloud originates at the face, and the exposure of the operator depends largely on how quickly this cloud spreads into the walkway. Water sprays on the shearer body can have a large effect on dust cloud spreading. Results to date indicate that sprays can help confine the dust cloud to the face if they are carefully placed. Otherwise they can make dust levels far worse. The worst offenders are often face-side sprays used to discharge cooling water from the cooling jackets of the shearer motors. These face-side sprays set up an air circulation pattern as illustrated in the drawing. Air induced by the sprays to flow towards the face, raises the air pressure in front of the face, which causes the air flow to turn and then move back over the shearer, bringing dust with it into the walkway.

Jan 1, 1981

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX C SCALING RELATIONSHIPS 1. Scaling Law for Fly Ash Crater Formation The scaling law derived for predicting crater diameters at different scales is developed below by considering the equation of motion of individual fly ash particles. It is assumed that the air drag on each particle is characterized by Stokes flow, and at the borehole - passage intersection the air velocity and the fly ash particle velocity are the same. The equations of motion for a fly ash particle are the following, (see Figure C-1).

Jan 1, 1973

By W. J. Pena, C. W. Owings

"Generally, the hazard of cool-dust explosions in tipples and cleaning plants is not given the consideration that is given it underground. This lack of consideration is probably due to failure to appreciate the potential hazard. An explosion in a tipple or cleaning plant is basically little or no different from an explosion underground. If bituminous-coal dust is raised into a cloud in the air and comes in contact with arcs from motor brushes, switches, or open flame, the dust is very likely to ignite, and flame will very probably propagate or extend through it if the quantity of dust per unit of air space is sufficient. The open space in a tipple or cleaning plant may reduce the violence of the explosion, but it is not likely to prevent ignition or propagation of flame.The movement of coal through a tipple or cleaning plant naturally puts into suspension a large amount of dust, which finally settles on exposed surfaces. Any disturbance that will put this dust into suspension in a sense enough cloud can result in the dust being ignited by an arc or open flame if one should be present. An explosion of bituminous-coal dust in a tipple or cleaning plant generally can be prevented either by keeping it thoroughly clean or by removing all sources of ignition, or both.The tests at the U.S. Bureau of Mines Experimental mine have shown that the explosibility of coal dust is proportional (other things being equal) to the ratio of the volatile matter to the volatile matter plus the fixed carbon, indicated thus:The volatile ratio for the Pittsburgh coal bed is calculated as follows:Therefore, as the volatile matter decreases the liklihood of ignition decreases; however, coal-dust explosibility depends on other factors also, such as fineness, dryness, and cloud density; and under some conditions other factors also intervene.Proof of the explosibility of coal dust in the absence of explosive gas has been shown in numerous cases in mines and mine plants and also by a series of tests. In these tests a dense cloud of dust is blown onto an open flame or an electric arc, almost invariably with resultant exploding of the dust. The Safety Division of the United States Bureau of Mines has made a number of demonstrations of the explosibility of Pittsburgh coal-bed dust, using a small gallery or box in which a cloud of coal dust is blown onto a lighted match; larger-scale tests have been made with an electric arc as the igniting agent. Bituminous-coal dust is readily ignited with a medium arc, but with low-volatile coals a larger arc is required. For test purposes, a 100-ampere arc has been used. Ignition has occurred readily under these conditions with Pocahontas No. 5 coal dust with ratios of volatile to total combustible of 0.232 to 0.253, and with Pocahontas No. 3 coal dust with a combustible ratio of 0.242. Lower Kittanning coal dust, with a ratio of 0.187, did not give definite ignitions, and Pocahontas No. 4 dust did not explode, although part of the coal-dust cloud ignited. It is probable that even the low-volatile coal dust will be found to be explosive with a higher-amperage electric arc as the initiating agent."

Jul 1, 1936

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA), U.S. Department of Labor, employees who serve as accident investigators for serious accidents and fatalities as part of their job duties. The subjects responded anonymously during a workshop on stress. The subjects consisted of randomly selected individuals, representative of locations across the country and representative of all mining commodities: coal, metal, nonmetal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalization, and reduced personal accomplishments. The average results of the scores for each of the three subscales fell in the moderate range for the study group of MSHA accident investigators. The scores within the moderate range show that the subject population was at the lower end of the range for emotional exhaustion and depersonalization, tending toward a lower burnout risk, while the group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. It is concluded that overall this group is at moderate risk for burnout, and the authors recommend follow-up with this population.