Search Documents

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Twenty-five years ago, the former U.S. Bureau of Mines funded a research project aimed at developing the enabling technology for incipient failure prediction in electric power system components as a means of reducing the injuries and fatalities that sometimes occur when equipment malfunctions. Over the ensuing years, interest in this has waxed and waned, but recently interest has been growing for both civilian and military applications. This paper addresses the level of turn-to-turn insulation deterioration that can be resolved using an on-line monitoring technique. The detection of turn-to-turn defects is especially important because they are believed to represent the beginning stage of most motor winding failures.

Improve transmission of data from an underground mine monitoring system to a remote, mass-data storage system. Background Instrumentation systems in underground mines must operate under environmental extremes of dust and humidity, local electromagnetic/radio frequency (EM/RF) interference fields, and potentially explosive atmospheres. During a recent roof-bolt study performed by the Bureau of Mines, it was necessary to transmit a large quantity of data to a data storage system. Conventional wire cable transmission presented several limitations which often required special electrical isolation or physical protection. Because conventional wire cable presented certain problems, the Bureau of Mines investigated alternative means of data transmission. The research investigation led to the selection of fiber optic cable for data transmission applications. The fiber optic method of data transmission offers several advantages: ? Since the transmission medium consists of light waves, it is safe to use in gassy mines. Where applicable, MSHA permissibility standards for peripheral devices must be met. ? It is lightweight and rugged. ? It can operate up to 131000 feet (4km) without repeaters and without EM/RF field interference.

Jan 1, 1986

Hang ventilating air curtains so that they can be installed, moved, opened and closed more easily than curtains that are spadded or nailed in place. Approach Low-leakage plastic curtains fitted with grommets along the top were threaded onto a steel cable which is suspended from roof bolt plates. The system was tested in two mines. How It Works The curtains are threaded onto a steel cable which is suspended from roof bolt plates by S-shaped hooks. See Figure 1. The outby end of the cable is reeled off a hand operated winch; the inby end of the cable is anchored to a roof bolt plate by means of a cable grip and an S-shaped hook. To install the curtains the following procedure is used. First, the winch is located at least 5 feet outby the last open cross-cut. The base of the winch can be secured to the mine roof with short roof bolts, only about a foot long.

Jan 1, 1978

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection with this work, the petrographic laboratory is called

Jan 1, 1940

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Systems Cost systems are organized methods of collecting, allocating, and accumulating resource utility expressed in terms of money. There are two major spheres of cost accumulation: financial accounting and cost accounting. Financial accounting deals primarily with historical costs and provides a means of measuring and recording cost events which have al¬ready taken place. While there are no legal requirements to control the methods of recording and reporting cost data in the United States, the procedures in use are guided by professional organizations such as the American Institute of Certified Public Accountants. The final pro¬ducts of financial accounting practices are the income statement and balance sheet which describe the financial status of the organization under study. Cost or managerial accounting is an expansion of financial ac¬counting procedures, providing more detailed cost breakdowns on present operations with one objective being the projection of present costs into the future. The projection process tends to limit the accuracy of the information; however, to management and project justification per¬sonnel, data on future operations tends to be of greater value. The basic principle behind cost accounting is the cost cycle. As products are developed from raw materials, the value of the work-in¬process increases due to the cost input of the various fabricating ele¬ments. Thus, from the basic input elements of facilities, labor, and raw materials, costs are added to each unit of production as a function of the work performed on that unit.

Jan 1, 1975

Mine closing methods should be carefully considered. If not properly sealed, an abandoned mine may continue to produce acid water. Since 60 to 90 percent of the total acid discharged from all coal mines is from abandoned mines,(58) some states require that provisions for sealing be contained in the mining permit application. Closing an operation to prevent harmful mine drainage into nearby runs and streams is a subject of much concern to states as a result of continuing problems from long abandoned mines which were improperly closed.

Jan 1, 1970

By W. H. Eddy

Laboratory batch and small-scale continuous flotation tests were con-ducted by the Bureau of Mines on a mica waste tailing from Kings Mountain, N.C., to determine the feasibility of producing high-quality mica, feldspar, and glass sand. Mica was recovered by two methods; one was by flotation in an alkaline circuit, which produced a mica concentrate assaying 92.0 percent mica with a recovery of 87.l percent, and the other by flotation in an acid circuit, which produced a mica concentrate assaying 91.0 percent mica with a recovery of 79.4 percent. Continuous flotation processing yielded a feldspar concentrate assaying 1.10 percent Na20 and 13.50 percent K20, with recoveries of 66.4 and 80.6 percent, respectively. The feldspar tailing was high-quality quartz glass sand analyzing 98.6 percent Si02 and 0.02 percent Fe203.

Jan 1, 1969

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

6. Computer Simulation of Mine Evacuation Analysis of mine evacuation involves manipulating a large number of interacting variables, such as mine passages, hoist movements, miner position etc. , which makes the problem very difficult to solve without use of a digital computer. Therefore, under this contract, a computer program is written to simulate evacuation of a mine under different configurations. The simulation input variables include characteristics of the mine, expressed in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self-rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i. e , fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effect of the fire on ventilation or on the miners is not considered. The simulation output includes the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure time of the miners. Details of the mine evacuation program are summarized in Appendices A and B Appendix A describes structure of the program and its capabilities. The flexibility of the program and its suggested uses are demostrated by a number of illustrative examples Appendix B is a user' s manual for the program which includes instructions for program use and explanation of the logic employed in the program. A computer listing and printout of a typical output are also included in the Appendix B The ten illustrative examples summarized in Section A 4 (Appendix A) provide proof of validity of the program and help make certain inferences about mine evacuation. The first example, which is simulation of an actual mine fire drill conducted in a mine, has predicted evacuation time within 5 percent of the actual evacuation time in the fire drill, demonstrating thereby, the ability of the program to make accurate predictions.

Jan 1, 1976

By Thomas P. Meloy

"The presence of respirable quartz-bearing mineral par-ticles has been well documented in many coal mines, and the Mine Safety and Health Administration regulations address the quartz content of mine dusts. Unfortunately, the correlation between the quantity of respirable quartz-bearing mineral particles and the pathogenicity of the dust is not strong. Work is currently underway by the National Institute for Occupational Safety and Health/U.S. Bureau of Mines and work is being included in the Respirable Dust Center Program by Dr. Seehra to determine the surface availability of quartz in mixed composition mine dusts. However, this paper propose a possible source of surface quartz or a spe¬cial region in the coal that may contribute to the pathogenicity of selected particles in the respirable dust.Assumed in this model is the hypothesis that either the cleat surface is coated with quartz or some cytotoxic sub-stance that in the body is capable of destroying macrophage and thus inducing a fibrotic response (1) that during the frag¬mentation a reasonable proportion of the respirable size coal particles contain some of the original cleat surface and that these particles have the same order of in vivo cytotoxicity as do the quartz particles. It may be that these cleat surfaced respirable size particles are only contributory to the overall pathogenicity of the coal dust, nevertheless, there are enough of these particles to to considered as a potential source of the cytotoxic dust particles.This paper demonstrates that if the cleat surfaces are mineralized with quartz or have a pathogenic coating, then in many mines there will be enough respirable coal dust particles containing some cleat surface to cause a fibrotic reaction. To understand why some of the dust particles contain as part of their surface some of the cleat surface, consider what happens when a beer bottle is broken. While there are a large number of beer bottle fragments, many of the fragments, particularly the larger fragment sizes, will have as a fraction of their surface part of the original beer bottle surface. The model and mathematics of this problem have been worked out by Meloy.(2-4)In the homogeneous IAC model, (2-5) a fragment or par-ticle resulting from comminution is equally likely to occur anywhere in the material being broken. Therefore the probability of a particle of size x having part of the cleat surface in it, p(x), is proportional to x. Thus:"

Mar 1, 1989

Provide the technology to remotely control a thin¬-seam continuous mining machine from a safe location hundreds of feet outby the working face in an underground room-and-pillar mine. Background and Approach Hard-wired or radio remote control of continuous mining machine has been commercially available since the early 1970's. This type of remote control, in low and high coal seams, situates the machine operator offboard, but within direct view of the underground coal face, Although positioned under supported roof, the operator can still be exposed to face area hazards that include roof-rib falls, dust, methane explosions, and equipment congestion. The U.S. Bureau of Mines approach has been to put the operator into a protected compartment at a location away from the working face. Since 1979, the Bureau has investigated innovative methods to better protect face area workers in under¬ground room-and-pillar mines. In 1989, the Bureau demonstrated an offboard, computer-based remote con¬trol system in a West Virginia highwall mining operation that stationed the operator hundreds of feet away from the working face. In late 1992, much of this technology, plus improvements, Was used to demonstrate, on the surface, how a thin-scam continuous mining machine could be remotely controlled 200 feet from the machine in a 36-inch working height.

Jan 1, 1992

By R. V. Ramani, A. S. C. Owili-eger

The origin of gaseous hydrocarbons in coal, predominantly methane, can be traced to the natural processes of coalification. The higher rank coals or the more deeply buried seams retain more gas than low rank coals or shallow seams. It is estimated that up to 460,000 cubic feet of all types of gases are produced during the formation of one ton of coal (Cervik, 1969). The chief components of these gaseous products are methane, carbon dioxide, nitrogen and water vapor. Most of these gases escape during the various stages of decomposition but with eventual presence of overlying impermeable beds, there may be as much as 2,000 cubic feet of gas retained per ton of coal. Over geologic time, diffusion and other processes such as geologic disturbances in the earth's crust remove all but 500 to 2000 cubic feet of gas per ton of coal (Cervik, 1969). It is this residual methane which is of primary concern when mine openings are made in coal measures. Extensive data compiled by the United States Bureau of Mines reveal that some coal mines in this country emit up to 20 million cubic feet of methane per day (Spencer, 1970; Irani et al, 1972). Toxic, poisonous and respirable gaseous pollutants and explosive gases, predominantly methane, are injected into the ventilation stream from active sections and gobs. The liberation of methane in gob areas may, under certain circumstances, become extremely large. In some instances it may constitute up to 70 percent of the total yield of gas in a mine. The basic physical factor which determines the yield of gas into the mine environment is the gas content of the seam. The influence of the gas content of a seam on the overall yield of gas

Jan 1, 1974

By H. R. Shell

Variations between laboratories on the silica and alumina content of calcined kyanite led to this Bureau of Mines study of the extent and nature of the differences. In particular, Bureau scientists hoped the study would lead to correction of the causes of the dissimilarities. A sample of calcined Kenya kyanite was analyzed by seven different laboratories familiar with silicate analysis. The compiled data indicated differences originating from lack of recovery of silica after two acidic dehydrations, from high alumina caused by several factors, from loss or gain of iron during sample fusion, and from indifference regarding the accurate determination of minor constituents.

Jan 1, 1959

By M. Terry Hoch, George J. Karabin, James M. Kramer

This paper introduces the fracture mechanics approach—a unique way to predict the stability of a coal mine panel. The technique uses analytic equations to calculate the stress, strain, and yield characteristics of coal support systems. It uses fracture mechanics to model almost every type of mine support structure. Another feature is a method that incorporates field-tested knowledge into the analytical analysis. For example, this technique can model the yield characteristics of a coal seam by combining empirical pillar strength equations into the analytic analysis. It may be possible to simulate multiple-seam mining by incorporating subsidence methods into the analysis. The method is simple and quick, which makes it attractive for stress analysis software. It should be more accessible to those in the mining industry who do not have expertise in rock mechanics or numerical modeling. Although the purpose of this research is for modeling coal mines, it should be adaptable to any mine in a tabular deposit.

Jan 1, 1999

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggest that many rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to sudden failures of rock and cemented sandfill surrounding stopes. We believe that the reduction of rock burst hazards must be based on a clear understanding of the basic mechanisms involved. The current work emphasizes the mechanical role of wall rock movement and seismicity in generating conditions that promote rock burst damage. Based on our interpretations of these mechanisms, we briefly address several hypothetical practices that could influence rock burst hazards in similar mining situations. The overall goal of this research is to advance the NIOSH mission of improving the health and safety of the nation’s workers.

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

To monitor the quantity and quality of air in underground mines to assure safe working conditions. Approach Several mine air monitoring systems, consisting of sensing stations in the return airways and control stations on the surface, have been Installed and tested. How It Works Sensor stations are located at strategic places in the underground mine. At each station, the sensors measure air velocity, air temperature, methane concentration, and carbon monoxide concentration. In one system, differential air pressure between intake air and return air, is also measured. Output voltages of the sensors are converted to digital signals at the sensor stat ion; these signals are multiplexed so that data from all sensors can be trans-phone wire to a central station. There the data are displayed and alarms are triggered when the sensed values exceed (or in the case of air velocity, fall below) a preset value. In addition to receiving data automatically, the central station can poll individual sensors at any time.

Jan 1, 1978

By Launa Mallett

This training material focuses on the content of emergency warning messages. Research has shown that when an emergency occurs, people often do not get the information they need for the purpose of taking appropriate action. This safety talk presents a procedure, using mental cues that can be used by senders and receivers of emergency warnings.

Jan 1, 1999

By Chelesa C. Woodward, Gregory G. Miller, Walter K. Utt, Wayne L. Howie

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. Researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are studying the use of a drill monitoring system to estimate the strength of successive layers of rock and assess the integrity of a mine roof so that roof drill operators can be warned when a weak layer is being drilled. Measurements taken during drilling can be converted to suitably scaled features so that a neural network can classify mine roof strata in terms of relative strength. The feasibility of this concept has been demonstrated in the laboratory. The research project was undertaken in order to increase the safety of underground miners, especially those involved in roof bolting. The system should be applicable to the mobile drills used in underground mining and would likely find wider application as well.

Jan 1, 2002

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990