Search Documents

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

Improve underground mine roof bolt support systems by alleviating problems associated with certain ground support systems currently being used. Approach Convert a passive resin-grouted roof bolt system into a uniform, tensionable roof bolting system. Background Resin-grouted roof bolts are one of the most common forms of ground support in U.S. underground coal mines. These support systems can be installed with a full-column of grout and be loaded with subsequent roof movements after installation. This is called a "passive" support system. An alternative to the passive support system is the mechanically-anchored, tensioned roof bolt system. This system is installed with resin grout. This system is designed to load or tension the support during installation by using a mechanical anchor, coupling, or threaded nut after the resin has properly cured. It is called an "active" support system and is used extensively for improved strata control in a laminated geologic deposition or in difficult ground conditions. To ensure that active bolts have been properly installed, the bolt loads must be checked by using a torque wrench or other suitable equipment. Unfortunately, this practice presents potential safety hazards and has limited accuracy. Laboratory and field experiments also reveal that the torque-to-tension ratio developed on active support systems can vary by 50% from bolt-to-bolt. Variations in bolt load installations can induce stress concentrations and lead to roof degradation or failure.

Jan 1, 1991

By A. E. Prokop, J. P. Rider

Previous research on continuous mining operations has shown that significant interactions exist between dust control parameter application and the resulting respirable dust levels, but simply increasing the level of the controls does not guarantee a reduction in respirable dust levels. Full-scale laboratory tests are being conducted to provide information to longwall operators which would assist them in selecting control parameters that would reduce dust levels for mine-specific conditions. The interactions between face air velocity, shearer water quantity, drum water spray pressure, external water spray pressure, and spray system design were evaluated in a simulated 2.13. m (7-ft) coal seam for two cutting directions. Locations around and downwind of the shearer were monitored to evaluate relative changes in respirable dust levels as a function of each control parameter.

In Maryland, coal mining is confined to Garrett County and the western portion of Allegany .County. Terrain in both counties is predominately level with rolling hills; state law prohibits surface mining in steep slope areas. The Conemaugh and Allegany geologic formations contain five major minable fields or basins. These include: Upper Youghiogheny, Lower Youghiogheny, Castleman, Upper Potomac, and Georges Creek. Maryland's coal reserves are estimated to exceed one billion tons. Approximately 490 million tons of bituminous coal are considered recoverable using conventional mining methods. After World War 11, deep mining declined in Maryland, and by 1977 surface mining accounted for 91 percent of the total production. Since then, production at underground mines has recovered, accounting for 69 percent of the coal production in 1991. Maryland's permanent regulatory program was fully approved February 18, 1982. Its Abandoned Mine Land Program was approved June 16,1982.

Jan 1, 1992

By T. M. Barton

This paper presents several case studies in which a mechanics-based boundary-element program is used to back-calculate the surface subsidence associated with various panels at several northern Appalachian coal mines. The program used in this case study is called LAMODEL, which incorporates a frictionless, laminated overburden into a general-purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin-seam or vein-type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from this work show that the LAMODEL program is not as accurate as available empirical subsidence-predictive methods: the expected correlation between the geology and the optimum input parameters is not evident. However, for a mechanics-based program, LAMODEL does provide moderately accurate subsidence calculations, and it is one of a few programs that can even attempt to practically calculate both underground stress and convergence and the resulting surface subsidence.

By G. W. Groove, E. E. Quenon

"INTRODUCTION Uncontrolled mine fires originating in exposed coal beds through the acts of careless or irresponsible persons present a serious threat to buildings, surface property, and the life and health of persons near the affected area. Apparently, the seriousness of such fires is not fully understood by property owners or those residing in the vicinity, as practically nothing has been done to alleviate conditions. In many instances, such fires have been active for several years before property owners or civic organizations have shown any interest toward having the fire extinguished. Recommendations by Bureau of Mines investigators in the interest of controlling such fires are seldom followed, as the Bureau cannot provide the funds for doing the work.Several uncontrolled and widespread fires are burning along the outcrop of coal beds and in underground abandoned mine workings within a 25-mile radius of Pittsburgh, Allegheny County, Pa. If these fires are permitted to continue to burn unabated, the ultimate results may be far-reaching. Most of the outcrop fires investigated are believed to have originated from burning rubbish, forest fires, or workmen, hunters, or others building fires near the outcrop of ,the coal beds. In other instances, smoke and fumes have suddenly appeared in the vicinity of abandoned coal-mine openings, indicating that a fire has either burned its way along the outcrop of the coal bed or has traveled through the abandoned mine from another location. An underground or outcrop coal-mine fire will be very likely to continue to burn as long as an oxygen supply is present.; and, so far as is known, such fires do not stop burning automatically until virtually all combustible matter is consumed."

Feb 1, 1948

Determine the extent of upper extremity cumulative trauma disorders (UECTD's) in the U.S. mining industry. Background UECTD's are injuries that develop gradually over a period of time as a result of repeated stress to a particular body part without adequate time between stresses for full recovery to occur. The stresses that contribute to UECTD's may occur because of the following work components: awkward position of wrist or arm, excessive manual force, high repetitions of manual movement and effort, cold environment, and vibration. Cumulative trauma injuries to the arm and hand have become an ever growing concern among safety and health professionals in a number of different industries and work settings, such as meatpacking operations, assembly-line work, and keyboarding. Mine workers arc also exposed to a combination of stressors and work design deficiencies that result in arm and hand injuries. For example, certain job tasks and environments, such as that of an underground jackleg driller, expose miners to segmental (hand-arm) vibration and cold temperatures. Operators of underground mobile equipment, such as scoops and trams, regularly have their hands in direct contact with vibrating levers and controls.

Jan 1, 1992

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

The Crow Indian Reservation is located in the southeastern part of Montana, stretching from near Billings, in the center of the state, to the Wyoming border in the south. The Office of Surface Mining's Casper, Wyoming, Field Office is responsible for regulating mining and reclamation on Crow tribal land. Federal legislation enacted July 11, 1987, authorized the Indian tribes to implement approved Abandoned Mine Land Reclamation Programs. In early 1988 the Crow elected to develop an Abandoned Mine Land Program under the Title IV provisions of SMCRA. The tribe's plan received final approval on January 4, 1989.

Jan 1, 1992

By E. F. Ferrell

The Bureau of Mines, U.S. Department of the Interior, studied the use of manganese sea nodules for catalytic oxidation in air of 1 pct carbon monoxide, 1 pct propane, and 1 pct methane. Catalysts were prepared from both Pacific Ocean and Atlantic Ocean nodules and compared with a platinum catalyst using a fixed-bed, steady-state microreactor with gas chromatographic analysis. Combustion temperatures with manganese nodules were 50° to 100° C lower than those with the platinum catalyst. Ion-exchange addition of rare-earth promotors to the nodule catalyst decreased combustion temperatures an additional 5° to 45° C.

Jan 1, 1978

By Kenneth L. Cashdollar

This paper reports US Bureau of Mines (USBM) research on the explosibility of coal dusts. The purpose of this work is to improve safety in mining and other industries that process or use coal. Most of the tests were conducted in the USBM 20 litre laboratory explosibility chamber. The laboratory data show relatively good agreement with those from full-scale experimental mine tests. The parameters measured included minimum explosible concentrations, maximum explosion pressures, maximum rates of pressure rise, minimum oxygen concentrations, and amounts of limestone rock dust required to inert the coals. The effects of coal volatility and particle size were evaluated, and particle size was determined to be at least as important as volatility in determining the explosion hazard. For all coals tested, the finest sizes were the most hazardous. The coal dust explosibility data are compared to those of other hydrocarbons, such as polyethylene dust and methane gas, in an attempt to understand better the basics of coal combustion.

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under parent regulations may not limit cable temperatures to less than 90 °C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, ell carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine foes. This paper describes a method of measuring the conductor temperature of untie trailing cables during no anal operation. The temperature is measured using a 50/175 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements arc made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

By C. B. Manula, R. L. Sanford, R. A. Rivell

Development of the Rail-Haulage Sub-assembly for the Production Sub-system (UGMHS)* required the use of ,a newly formulated model in order to best satisfy the requirements. Many of the ideas of the former single-stage rail simulator included in the original version of UGMHS have been used, together with the results of experience gained in applying the earlier model to a variety of operating situations (Sanford, 1969). The sub-assembly is developed as an independent system and, as such, can be used to analyze track systems using production distri¬butions as data input. In addition, since this model is designed to replace the original sub-assembly in UGMHS, the linking procedure is identical with respect to bi-directional information flow. The flow of coal from production sections, for example, fills the mine cars, but a condition of "out of empties" or "full of loaded" at a loading station will shut down inby production sections. A requirements analysis was conducted to determine specifically how the model could best serve the user. Operating management had the largest input in developing the following requirements for the Rail Sub-assembly: a) data input in mixed narrative - numeric form to permit user identification of the input variables; b) a user option to extract several ranges of detail in model output, i.e., an average shift summary of minimum retrieval

Jan 1, 1974

By Kathleen Kowalski-Trakofler, Edward Barrett

Problem: It is estimated that 5 to 10 arc flash explosions occur in electric equipment every day in the United States. In the mining industry the largest single injury category of electrical injuries are caused by non-contact electrical arcs. Method: This investigation progressed in two phases: (a) 836 Mine Safety and Health Administration (MSHA) reports of electric arcing incidents that occurred over a period of 11 years were reviewed, and (b) personal interviews were conducted with 32 individuals. A theoretical Safe Job Performance Model guided the study. Results: Behavioral dimensions were identified and included the effect of worker experience, judgment and decision-making ability, behavioral and organizational controls, and safety culture. Summary: The National Institute for Occupational Safety and Health (NIOSH) conducted an investigation of behavioral components associated with arc flash incidents and developed recommendations for interventions based on findings. Impact on Industry: This study fills a vacuum in electrical training with a focus on the organizational and behavioral aspects of arc flash incidents. There search is cross-cutting in its scope, in that the results apply not only to mining and construction, but many other industries employing electricians. Although the majority of mine electrical injuries are the results of burns from electrical arcs, few miners are aware that such a hazard exists. A safety training program, which includes a video and an instructor's discussion guide, was developed for electricians based on this study's findings. “Arc Flash Awareness” was released in 2007 (DHHS NIOSH PublicationNo.2007-116D) and is available through1-800 CDC-INFO. Phone:1-800232-4636 or email cdcinfo@cdc.gov. It is also available from MSHA at MSHADistribution@dol.gov or 304-256-3257 (DVD-576). Private industry is producing Portuguese and Spanish language translations.

By D. O. Kennedy

THIS CHAPTER on minor nonmetals covers greensand, meerschaum, mineral wool, and wollastonite. Mineral wool was by far the most valuable material among these minor nonmetals reported in the United States in 1956. GREENSAND Output of greensand (glauconite) declined in 1956. The Kaylorite Corp., Dunkirk, Md., and the Inversand Co., Sewell, N. J., were the only firms that reported production of this commodity. Output came from open pits in Calvert County, Md., and Gloucester County, N.J.

Jan 1, 1958

By D. Harrington, M. W. Von Bernewitz

"The erection of barricades by men who are shut off from escape in mines at time of fire or after an explosion has been consistently advocated by the United States Bureau of Mines. Largely through the publicity given by the bureau to this excellent type of emergency safety endeavor, several hundred lives have been saved during the past 20 years. One of the earliest instances of barricading in the United States of which there is fairly complete record was in connection with the Cherry mine fire in Illinois in 1909; in this fire 259 lives were lost, but 20 men were saved by two barricades and were brought safely to the surface after seven days. In another coal-mine fire, followed later. on by an explosion, at Delagua, Colo., in 1910, 79 lives were lost, but 18 men saved themselves by erecting canvas brattices or barricades; the miners in one barricade were removed safely after five hours and those in another after 21 hours. In 1911, after an explosion in a coal mine at Briceville, Tenn., in which 84 lives were lost, five persons were brought out alive after 58 hours behind a barricade. Twenty hours after an explosion in which 73 were killed at McCurtain, Okla., in 1912, 13 men were taken out alive and one dead from behind a barricade or partition constructed of canvas. In 1914, after an explosion at Eccles, W. Va., in which 181 were killed, 35 men barricaded themselves in one place and after four hours were brought to the surface alive; this barricade was also of canvas. In 1915, 112 men were killed in an explosion at Layland, W. Va., but two groups of men, 47 in all, were able to barricade themselves; after four days 46 men were rescued alive, but one man was dead. In 1915, an explosion at Boomer, W. Va., killed 23, but 27 others barricaded themselves in one place and after seven hours came out alive. All of the foregoing instances of barricading were in coal mines. In 1917 there were three cases of barricading in a Montana metal-mine fire (the North Butte) during which 163 lives were lost. One of the barricades, sheltering 19 men, failed because the region barricaded was in porous broken ground through which the poisonous gases seeped and killed the entire group. From another of the barricades, engineered by an assistant foreman, 8 men were taken out, 6 uncon¬scious and 2 dead, 50 hours after the fire started. The 6 unconscious men lived, out the assistant foreman who directed the men was one of the 2 who had died. In the third case of barricading in this metal-mine fire,,men, also led by an assistant foreman, kept themselves closed in for about b6 hours and then broke barricade or bulkhead, 25 oing in one direction to safety, and 4, including the assistant foreman, going in another direction to death from poisonous gases. There have been a number of other cases of barricading, some successful and others a failure. Probably the worst failure was that in the argonaut (gold) mine fire in California in 1922; all of a group of 46 miners behind a barricade were found dead when reached after 21 days."

Apr 1, 1933

By G. S. Morrow, C. D. Litton

This report presents the results of a U.S. Bureau of Mines evaluation of smoke detectors placed in conveyor belt entries of underground coal mines. The selected mines are located in six different Mine Safety and Health Administration (MSHA) districts, are operated by seven different companies, and use atmospheric monitoring systems from seven different manufacturers. Principal concerns are early detection and warning of fires, reliability of operation, frequency of maintenance, and adaptability of detectors to monitoring systems and the mining environment. The data contained in this report provide for some comparisons between smoke detectors and CO sensors, specifically in the areas of early detection of fires and susceptibility to nuisance alarms due to diesel exhaust contaminants. Finally, recommendations for performance standards, sensitivity tests, detector classification, and maintenance are presented.

Jan 1, 1992

By Lloyd A. Morley, Robert Stefanko

This report has presented a literature review of explosion proof¬ing of coal mine electrical equipment. The international "state-of¬the-art" is an extremely difficult definition to quantify but, from the preceding paragraphs, it is evident the international community be¬lieves that it is represented by the International Electrotechnical Commission's Publications. Five questions were set forth during the beginning of this report. Each will be evaluated in light of the preceding discussion. 1. Can Schedule 2G specifications on explosion-proof containers be substantiated? Literature was found in the three main problem areas, surface temperature, mechanical strength, and explosion transmission, to determine this. Surface temperature requirements are adequate except for equipment that can normally overload, and the required intern¬al pressure does afford some margin of safety. However, in terms of safety, gap dimensions are about ten times smaller than that needed. 2. Is it possible to replace the Schedule's design requirements with performance specifications? Two primary areas were determined as mechanical strength and explosion transmission. As was mentioned, for present flange and gap standards, the 150 psig requirement is adequate. Furthermore, it is the authors' opinion that the level cannot be re¬duced if the present gap requirements are retained. The Schedule now requires that 16 tests be run, but the literature suggests that only from three to six examinations are necessary. Then by using the abso¬lute maximum pressure from these measurements or 150 psig, whichever is

Jan 1, 1974

To provide a method for locating trapped miners promptly and accurately. The Approach: Develop a wireless emergency system that is intrinsically safe, compact, easy to operate, reliable, sturdy, and economical. How It Works: A (one transmitter has been developed under Bureau of Mines contracts. The transmitter weighs only a few ounces, is powered by a cap lamp battery, arid can be carried on the miner's belt. A compact loop antenna, which could either be carried by the miner or strategically located in the mine, is used to generate a magnetic field that is sensed by a mobile receiver on the surface. When needed, the antenna is deployed to form a single loop. In mines where the overburden is less than 600 feet, a loop of No. 19 wire approximately 30 feet in circumference is normally adequate. This antenna weighs less than one half pound. In deeper mines, a heavier wire and bigger loop is required; a No. 10 wire deployed around a pillar has been used.

Jan 1, 1974