Search Documents

By R. V. Ramani, V. T. Burgos, J. A. McClay

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herlckes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to September, 1974. Thls report was submitted by the authors on February 13, 1975.

Jan 1, 1975

By Tye J. Lasich

This project involved modeling rock masses with varying Rock Mass Rating (RMR) values to determine the degree of instability that develops around an underground opening as a function of RMR. The modeling was performed using Itasca?s UDEC distinct element software, which allows explicit modeling of blocks of rock and how they interact with each other. The analyses included three different orientations of the joint sets, four different joint spacings and three different values of joint strength, which combine for a total of 36 different combinations of model parameters. Two different modes of behavior were observed: local failure of area immediately surrounding the roof and sides of the opening, and deep-seated failure extending a large distance beyond the opening. Quantification of the size of the unstable area that developed provides numerical validation of empirical guidelines used in design of ground support and instrumented monitoring systems.

Jan 1, 2005

By M. Townsend, E. L. Petsonk, B. Fedders, M. Niggemeyer, H. Abrons, E. Daniloff, J. Griffin, K. Kinsley

In certain populations, nonspecific airway hyperreactivity (HR) is associated with increased respiratory symptoms and decreased lung function. We analyzed standardized pulmonary symptom questionnaires and pre-shift spirometry with methacholine inhalation challenge (Chatham, M. et al, Chest 82: 15) on 228 control workers (C) with no known exposure to occupational hazards, and 200 underground bituminous coal miners (M). M and c were similar in age, height, sex, and smoking status. HR (defined as >15% fall in FEVI after up to 5 vital capacity breaths of 25mg% methacholine) was found in 25% of M and 28% of C (NS). M showed higher% predicted FEVI (%PFEV) than c (M 107%, C 104%*). 28% of current smokers showed HR versus 22% of never smokers (NS). Current smokers showed reduced %PFEV but were not different from lifelong non-smokers regarding prevalence of HR. Subjects with HR showed reduced %PFEV, (HR 101%, not HR 107%*) but M and c with HR showed similar reductions. M had more dyspnea and chronic cough than c*. Hyperreactivity was associated with increased symptoms in controls but not miners. In our study, the prevalence of HR in coal miners was similar to nonminers, and did not explain miners' respiratory symptoms. * P < 0.05

Jan 1, 1989

This report, which updates and supersedes the Office of Surface Mining&apos;s 10-year progress report published in 1987, deals with the accomplishments of the regulatory and abandoned mine land reclamation programs during the first 15 years of the Surface Mining Control and Reclamation Act of 1977 (SMCRA). Part 1 is an illustrated description of on-the-ground accomplishments; Part 2 presents statistical information for the 15-year period. The data in this statistical report are organized in two sections: national statistics and state statistics. The national statistics provide an overview of coal mining and the implementation of SMCRA since 1977. The information reported for the states presents a brief description of the coal reserves in each area, accompanied by detailed statistics and graphs that relate each state to the nation as a whole. The statistics compiled in this report are from the Office of Surface Mining&apos;s files, computer data systems, and annual reports. During the early years of the program, many of the data categories were evolving and changing; therefore, data reported over the 15-year period are not complete for all states for all years, and where data was unavailable or zero, a dash (-) is shown for that item. The data sources used to compile the tables and graphs are listed and described in detail on page 76. Due to the number of requests for this information in the past, statistical information about coal mining and its regulation will be available each year as an appendix to the Office of Surface Mining&apos;s Annual Report to Congress. Beginning in Fiscal Year 1993, this information will be compiled and published on an annual basis. For more information about this report, call or write the: Public Affairs Office Office of Surface Mining 1951 Constitution Ave., N. W. Washington, D.C. 20240 (202) 208-2553

Jan 1, 1992

By H. W. Lang

The Bureau of Mines conducted an investigation to observe the effect of cetane improvers upon nitrogen oxides concentration in diesel exhaust gas. Amyl nitrite and amyl nitrate were used as additives to the fuel used in a four-cycle, single cylinder type test engine. It was concluded that nitrogen oxide concentrations were not enhanced at fuel-air ratios above 0.03 pound of fuel per pound of air.

Jan 1, 1969

Ever since the problem of mine pollutant waters has been under consideration, different mining methods have been investigated to abate the pollution problem. Two such methods which have been reported are inert gas operation and revised mining methods.

Jan 1, 1970

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This paper reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Research to reduce these accidents includes improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 2000

In the last few decades, a considerable amount of effort was directed at accurately determining the coal pillar strength to use for safely designing coal mines. The outcome of this early work was the well known Obert-Duvall, Holland-Gaddy, Bieniawski, and Salamon-Munro equations for coal pillar strength. All of these equations were developed for, and were calibrated with, pillars in a large room-and-pillar area such that the loading could be determined using the "tributary-area" theory. In order to account for the abutment loads associated with full-extraction mining, the empirical methods have typically adopted a simple conceptualization of the abutment load through use of an "abutment angle." Short of a complete numerical or analytical analysis of the coal seam and surrounding strata, very little work has been Fretted toward refining the empirical analysis of pillar loading. It appears that the vast majority of the research has been directed at determining the pillar strength, the numerator of the safety factor equation, when the denominator of the safety factor equation, the pillar loading, plays an equally important role in pillar design. This paper will address the deficit of pillar loading research by exploring the accuracy of the empirical abutment load calculations using insight provided by an elastic overburden model, a laminated overburden model and field observations. Ultimately, it is determined that a constant abutment angle probably over-predicts the abutment load as the mining depth increases.

The generally disappointing results obtained in the present study, together with the high material costs involved, preclude any general recommendation for a continuation of the work. One recommendation arises, however, from some observations on the application of latex to spoil banks. It was found that dilute latex used on a slope of spoil bank material at an application rate of 400 lbs per acre (dry basis) stabilized the soil and made it much more resistant to washout by rainfall. It is recommended that a study be conducted to use latex for temporary stabilization and/or sealing of spoil banks before and during reclamation procedures, on coal slurry ponds and coal refuse piles.

Jan 1, 1972

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Ahmed, M.,• "Development of an Integrated Control System for Mine Ventila¬tion and Firedamp Drainage," Mining Engineer, Vol. 127, No. 91, April, 1968, pp. 382-392. Andrews, J. W., "U. S. Mine Ventilation Standards," Paper presented at the International Mine Ventilation Congress, Sept., 1975. Boyle, J. A., and Conn, 0. S., "The Control of Mine Ventilation Utilizing Multiple Main Fans," Paper presented at the Seventy-second Annual CMIA Meeting, Pittsburgh, December 1958. Collinson, P. L., and Vance, W. E., "Mine Ventilation Planning," The Mining Engineer, Volume 121, No. 14, 1961, pp. 141-156. Committee on Industrial Ventilation, Industrial Ventilation, 12th Edition, 1972. Grever, R. E., "Automatic Monitoring of Ventilation Conditions in European Coal Mines," Symposium on Engineering Systems Design for Mine Safety, Michigan Technological University, August 1973. Hall, C. J., Airflow in Mines - Thermodynamic and Motive Column Analyses, The Book Concern, Printers, Inc., Hancock, Mich., 1967, 263 pages. Hargraves, A. J., "Planning and Operation of Gaseous Mines," Canadian Mining and Metallurgical Bulletin, Vol. 66, No. 731, March 1973, pp. 119-128. Harris, E. J., "The Fluid Network Analyzer as an Aid in Solving Mine Ventilation Distribution Problems," SME-AIME Transactions, Vol. 228, 1963, pp. 391-395 Higgins, J., and Shuttleworth, S. E. H., "A Tracer Gas Technique for the Measurement of Airflow in Headings," Colliery Engineering, November 1958, Vol. 35, pp. 483-487. Kaiser, K. M., and Bhowmick, B. C., "Recent Developments in Mine Ventila¬tion Instrumentation," Journal of Mines, Metals & Fuels (INDIA), June 1974, pp. 155-162. Kalasky, J. D., and Krickovic, S., "Ventilation of Pillared Areas by Bleeder Entries, Bleeder Systems, or Equivalent Means," Trans¬actions AIME, Volume 254, December 1973, pp. 284-291. Mahajan, J. K., "Ventilation Planning for a Deep Metal Mine," Min. Geol. Met. Inst. India, Volume 69, 1972, pp. 31-38.

Jan 1, 1977

By C. A. Herbert

"The Bureau of Mines for a number of years has conducted experiments at its experimental mine near Bruceton, Pennsylvania, on the explosibility of coal dust, with particular reference to dust explosions in coal mines, and the knowledge so rained may well be applied to the handling of coal dust at industrial plants and elsewhere.Powdered coal is coming into use more and more as a fuel, and the dangers incident to its use should be recognized and guarded against, as a number of accidents have occurred in recent years due to ignorance of this danger or to carelessness.Within the past three years two very serious accidents, under almost identical circumstances, have occurred on the surface at two different coal mines in Southeastern Iowa, due in each case to the sudden ignition of a cloud of fine coal dust.The first accident resulted in the burning of six men, three of them fatally; the second burned eleven; three men died as a result of their burns.The mines in the Southeastern part of Iowa, where these two disasters occurred, are operating in a thin coal bed averaging about three feet in thickness, and are worked on the long-wall advancing system similar to that of Northern Illinois.The miners in this section are paid on a screened coal basis; in other words, receive no pay for the fine coal. As a result they use forks in loading the coal into the mine cars, and naturally a considerable quantity of coal is left along the roadways. Subsequently this fine coal, together with the roof rock that is taken down to give sufficient height on the roadways, is loaded into cars and dumped in piles on the surface. This roof rock is a block, oily shale and the contribution of fine coal and oil shale gives ample combustible material to thoroughly burn the rock as it is dumped."

Jul 1, 1923

By Robert C. Hickman

"INTRODUCTION The Cline mine has been worked intermittently for copper and gold since 1895. Scheelite has recently been detected with the aid of a ""Mineralite"" on the old waste dumps of the mine. Four diamond-drill holes were drilled by the Bureau of Mines from August 13 to September 25, 1946. Results of this drilling showed the vein to pinch at depth and to carry no mineralization of economic importance.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigation work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.Acknowledgment is due Dr. Jasper L. Stuckey, State geologist, for logging the drill core and to J. B. Zadra and associates, Metallurgical Branch, College Park, Md., for analytical determinations."

Feb 1, 1948

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted at the Bureau's Mount Weather Testing Adit, Mount Weathe, Va. The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Reveille, mining-ngineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gave valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

1. In 2002, a total of 2,065 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 14.2% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,910) and anthracite mines 7.5% (n = 155) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (28.7%), West Virginia (21.7%), and Pennsylvania (20.1%).

Jan 1, 2004

By John W. Frey

This paper presents one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Persia has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers , to whom it is being referred through the courtesy of the Department of State .

Nov 1, 1929

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine&apos;s production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA) employees kom the US Department of Labor. These employees serve as accident investigators for serious accidents and fatalities as part of their job duties. During a workshop on stress designed for them, subjects volunteered anonymous written anecdotes, confirming and illustrating the findings. The subjects represented locations across the USA and all mining commodities: coal, metal, non-metal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalisation, and reduced personal accomplishments. The average results of the scores for each of the three subscales for the study group of MSHA accident investigators fell in the moderate range. These scores show that the subject population was at some risk for emotional exhaustion and depersonalisation, tending toward burnout. The group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. From this outcome accident investigators may be at moderate (note: this does not mean average) risk for burnout. The authors recommend follow-up with this population - specifically in training to work with grieving families; and greater organisational support for the accident investigators in this area would be appropriate. Keywords: Burnout; accident investigators; occupational safety and health; job stress.

By William D. Monaghan, Thomas H. Dubaniewicz, Kenneth L. Cashdollar

Emerging laser technologies are quickly gaining acceptance in the industrial workplace. Besides the risk of human exposure, one safety concern with the more intense lasers is the potential for ignition of flammable gases, vapors, dusts, fibers, or flyings often found in hazardous (classified) industrial settings. In underground coal mines, lasers are being considered for remote measurement of explosive methane gas. Current federal safety regulations for underground mines contain no specific guidance for evaluating the safety of optoelectronic components such as diode lasers. The National Institute for Occupational Safety and Health is conducting research to help provide a scientific basis for developing appropriate safety guidelines for optical equipment in the presence of flammable methane gas and/or coal dust. One phase of the study is an experimental evaluation of methane-air ignition by laser heated small particles. Minimum observed igniting powers for laser energy delivered by 200-, 400-, and 800-um core diameter fiber optic cables and directed onto selected targets in methane-air atmospheres were 0.6, L l, and 2.2 W, respectively. Comparisons are made with other ignition phenomena, including heated wires.

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

Pulmonary inflammation is accompanied by increased microvascular permeability and leakage of plasma into alveolar spaces. Serum has been shown to affect superoxide (O2-) production from pulmonary alveolar macrophages (PAM) in vitro, and in some cases serum has been shown to be necessary for stimulation of PAM. An electro-optical method was used to measure O2- production from single PAM by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from videorecorded images of individual cells. PAM were stimulated by their initial attachment to culture dishes independent of serum. The addition of 2% serum to the culture medium increased NBTH2 production during attachment, whereas concentrations of 5 and 10% serum had no additional effect. In contrast, PAM incubated for 2 hrs could not be stimulated by phorbol myristate acetate (PMA) or zymosan particles to produce O2- unless serum was present during the incubation and/or stimulation; however, NBTH production was similar in all cases of serum addition. Also2, serum alone did not stimulate adherent PAM indicating that serum is necessary but not sufficient for stimulation of attached. PAM. These results suggest that changes in microcirculatory permeability may have a pronounced effect on superoxide production by PAM and that serum may help regulate or condition these cells during inflammation of the lung. (Supported by USBOM Gll35142.)

Jan 1, 1988