Search Documents

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By Oliver Bowles

The United States Bureau of Mines has within its ranks a group of engi- neers who are engaged in working out quarry problems, the solution of which will be of general benefit to the industries involved. The problems undertaken are approached in a systematic and thorough manner, all the evidence for and against any proposed change or new development being collected as carefully as an attor- ney would prepare his data on an important case. Unlike the attorney, however, the Bureau engineer does not take sides; his judgment is based entirely and in- partially on the array of facts presented. In order to gain the desired infor- mation he visits many plants, consults with the leaders in the industry, works out experiments in his laboratory, and supplements this information with a stu- dy of all available literature already published on the subject in any part of the world. As an engineer who has for eight years conducted such inquiries in the stone industry, I propose to discuss the Bureau of Mines viewpoint; and it may be of interest to consider with me in a brief and general way the engineer's method of looking at quarry problems, and some of the results attained through past and present labors. While the Bureau has conducted no investigation directly for the crushed- st one industries, two years of investigative work at cement-plant quarries, and work now being conducted at lire-plant quarries, has a very direct bearing on the problems of the crushed-stone industry, since stripping, drilling, blasting, loading, and transportation are similar in many respects in all stone quarries. The results of cement-plant quarry investigations are to be found in Bureau of Mines Bulletin #160. (b) Two short papers on lime-plant quarry problems have been issued in mimeographed form as Serial #01 (c) and Serial 3 (d).

Jan 1, 1923

By Donna L. Anderson

This information circular documents the status of a laser-based guidance system to track and control the tramming maneuvers of a continuous mining machine. The work is part of a multiple project effort at the U.S. Bureau of Mines to develop technology for computer-assisted mining systems. The system includes stationary offboard laser-scanning sensors that report the angular coordinates of retroreflective targets on the mining machine. A microcomputer system processes the angular coordinates, determines position and heading, handles requests for data, and controls tram maneuvers of a continuous mining machine. This report describes the hardware for the sensor and computer systems and the software algorithms for continuous miner position and heading determination, closed-loop tramming, and data request handling. Improvements made to the system since previous documentation include the rewriting of the software on a stand-alone real-time microcomputer system, the implementation of real-time programming techniques, the use of a new version of the laser sensor, and the design and development of explosion-proof enclosures for the lasers and corresponding power supply.

Jan 1, 1991

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract HO 395132 to develop improved sensor cells for use in direct-reading detectors and diffusion exposure meters. A pumped CO sensor cell was developed which has a shorter response time, improved temperature cycle characteristics, and improved linearity and stability at high CO concentrations. Diffusion CO sensor cells have shown good response level stability and linearity up to 1000 ppm. In addition, a new sensor cell catalyst has been developed for NO2 sensor cells which has a much shorter response time and improved response stability characteristics.

Jan 1, 1982

By K. K. Kelley

The collection and correlation of thermodynamic data concerning substances of metallurgical interest have constituted one of the major activities of the Pacific Experiment Station of the Bureau of Mines, at Berkeley, Calif., for the past several years. Earlier bulletins (32, 33, 34, 36, 36, 37, 38) s in this series are entitled: (1) Contributions to the Data on Theoretical Metallurgy. I. The Entropies of Inorganic Substances; (2) Contributions to the Data on Theoretical Metallurgy. II. High-Temperature Specific-Heat Equations for Inorganic Substances; (3) Contributions to the Data on Theoretical Metallurgy. III. The Free Energies of Vaporization and Vapor Pressures of In¬ organic Substances; (4) Contributions to the Data on Theoretical Metallurgy. IV. Metal Carbonates--Correlations and Applications of Thermodynamic Properties; (5) Contributions to the Data on Theoretical Metallurgy. V. Heats of Fusion of Inorganic Substances; (6) Contributions to the Data on Theoretical Metallurgy. VI. A Revision of the Entropies of Inorganic Substances-1935; and (7) Contributions to the Data on Theoretical Metallurgy. VII. The Thermodynamic Properties of Sulphur and its Inorganic Compounds. The present paper collects and discusses thermodynamic data relating to metal carbides and nitrides, with the view of obtaining usable heat and free energy of formation relationships. Pertinent data on both classes of substances are difficult to obtain experimentally and consequently are extremely rare; it is therefore necessary in many cases, if equations are to be derived, to introduce certain approximations and assumptions. Lack of adequate means of checking results by utilizing data of different types, such as was done frequently in the bulletins dealing with carbonates and sulphates, are readily apparent to anyone who has made even a cursory examination of the available information. Consequently, some of the relationships derived undoubtedly will be found to be inaccurate when more or better data become available. Nevertheless, in view of the importance of some of these substances, it appears worth while to consider the information available at present and to attempt the formulation of as complete a

Jan 1, 1937

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

Ground and air vibrations induced by large surface blasts have been monitored. These field results, as well as a large number of published results, have been used to assess the performance of existing predictors and for the development of improved prediction methods. Field monitoring has been performed, with four seismographs giving complete wave records, at limestone quarries, coal strip mines and an open pit copper mine. Conventional analysis includes least square fitting of peak particle velocities and peak air overpressures with scaled distance formulations. Frequency content has been analyzed, and correlated with blast design (detonation sequence). Two new methods have been developed for predicting ground vibrations induced by blasting. The proposed analytical predictor accounts explicitly for inelastic attenuation and geometrical spreading, and calculates the peak particle velocity as a function of charge weight and distance. Statistical analysis of case studies confirms the consistent improvement over conventional scaled distance predictors. The second new predictor is a computer program simulating blasts, including blast geometry, charge distribution and detonation sequence, and simulating propagation of individual pulses to any point of interest, where effects are summed. A complete blast vibration results, allowing prediction of frequency content and duration as well as peak velocities.

Jan 1, 1983

By Steven J. Page, Wm. Randolph “Randy” Reed, John A. Organiscak

Researchers studying dust generation from blasthole drills developed a simple, quick fix that reduced respirable dust concentrations by more than 63% at the dump point. This device, which requires almost no maintenance, is small and inexpensive, and it will help operators maintain compliance to the dust standard. The thought process was that a reduction of respirable dust at any of the multiple sources on the drill, in this case the dust collector dump point, should reduce the total respirable dust generated by the drill. The U.S. Mine Safety & Health Administration (MSHA) has a coal respirable dust standard of 2 milligrams per cubic meter (mg/m3) for an 8-hour shift. MSHA and mine operators periodically collect personal dust samples to determine compliance with this dust standard. Drill operators have one of the highest exposure levels to respirable dust. This has been proven through many reviews of the MSHA dust sampling database. Prior to 1987, the highwall driller at surface coal mines had the most severe exposure to respirable silica dust, a trend that continues today based on MSHA's respirable dust sampling database. A review of the MSHA database for the years 1985 through 1992 shows that 81% of the respirable silica dust samples taken exceeded the permissible exposure limit for the highwall drill operator at surface coal mines. A more recent review of the MSHA database, for the years 1996 through 2000, shows that only 31% of the respirable silica dust samples taken exceeded the respirable silica dust limit for the highwall driller at surface coal mines. This suggests a substantial improvement in preventing the exposure of silica dust to the highwall drill operator. The drill operator, however, still tops the list of job occupations that have the highest exposure to respirable silica dust Respirable dust has been shown to be harmful to human health, especially when silica is present in the dust. It causes a disease known as silicosis, which can occur in three levels: chronic silicosis, which occurs after 10 years of exposure; accelerated silicosis, which occurs between 5 and 10 years of exposure; and acute silicosis, which can occur within a few weeks to five years of very high exposure to silica dust. Respirable dust consists of the dust particle size fraction whose median diameter is 4 micrometers (µm). The drilling machine generates high concentrations of respirable dust from several sources: drill table shroud leakage, dust leakage through the table bushing, dust discharge from the dust collector exhaust due to impaired filters, and dust entrained from the dust collector fines dumped onto the bench. The National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Lab (PRL) has been studying different methods to reduce respirable dust from these sources. During its testing, the institute identified a simple solution that reduces the amount of respirable dust generated at the collector dump point.

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By W. N. Patterson

The three major objectives of this contract were (1) to survey underground diesel-powered mining machinery to determine noise exposure problems, (2) to recommend noise control techniques, and (3) to develop a technique for predicting underground sound levels from surface sound power measurements. The objectives were achieved. The contractor developed information on the severity of the noise problem caused by diesel engines underground and pinpointed the equipment causing the problems. He recommended a number of corrective techniques that can provide relief until long-term solutions are found. A procedure for predicting underground noise levels from above-ground measurements of the machine noise was found valid for several cases tested.

Jan 1, 1975

By M. Jaffe

The data developed in this study establishes the technical and economic feasibility as well as the improved health and safety characteristics of a novel mining concept. The mining concept is a modified longwall technique using prestressed tendons for roof control, longhole blasting for fragmentation, and remote mucking. The technical feasibility was found to be dependent on the state of the art, while economic feasibility was found to be dependent on particular minerals and on supply and demand. Since these two conditions are not necessarily coincident in time the data is presented in the report in a manner that enables the mining engineer to perform a rapid preliminary technical and economic analyses for a specific property.

Jan 1, 1977

By J. Sammarco

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to determine if light-emitting diode (LED) cap lamps can improve safety by reducing glare. Glare can impede a miner?s ability to see hazards and to safely perform their work. Another objective is to determine if a person?s age is a factor. This is important because the workforce is aging ? the average miner is now about 43 years old. Three cap lamps were used to evaluate glare: an incandescent cap lamp, a commercially available LED cap lamp and a NIOSH prototype LED cap lamp. Thirty NIOSH personnel from the Pittsburgh Research Laboratory (PRL) served as test subjects. Three age groups were established with ten subjects in each group. Testing was conducted in the Mine Illumination Laboratory (MIL) of NIOSH PRL. The results indicate no statistically significant difference in discomfort glare among the incandescent and LED cap lamps. However, an analysis of variance for disability glare indicates that the LED cap lamps were superior for the older subjects. Disability glare scores for the oldest subject group improved 53.8% when using the NIOSH prototype LED cap lamp compared to the incandescent cap lamp and 36.5% compared to the commercial LED cap lamp. It ap­pears that, given the conditions of this study, LED cap lamps will not increase discomfort glare and can enable significant improvements in disability glare for older workers. It is also evident that not all LEDs are created equal. The disability glare improved the best for older workers when they used the NIOSH prototype LED cap lamp, which has a different spectral power distribution (SPD) (more short wavelength energy) than the commercial LED cap lamp. Therefore, for disability glare, the results suggest that the SPD is an important factor to consider in cap lamp design.

Jan 1, 2009

By Robert L. Lagace

[Suuple Iheorctrccil models are I'M lllolalcd to cltaraclerl/c medium frequency (MF) radio vase pi opaiation in undcrgiounli room arid pillar coal mines fur the purpose of predleiln the most lavolable operating fIegtucncics,md nr,ixunum communic;IIIoil ranges for pottahIe rldu)s with I top antennas. I or conductul IrCC areas, at hree layer propaeaIion IltodcI wit II a Iiallsmissloil IIIIi- lhlllllIIal'u11 lot the plupa!edti ii unlstallt Iris been dcvcloped ;md verified experimentally. 1 lie mode u1 propaCaUetl lakes Ills form of i parallel plane (0,t)) TIM lransnussu)nhne 1% PC of mode with the electric held vertical and the magnetic held hoti/cntal t itliin a planar coal scam in which the tunnels Can he ignored and which 1s hounded above and below hp richer conductivity rock. 1lie model lilt the data best river the 200 io 1000 kH/ frequency hand and exhibits a rc;;lon of optlnrul1l Pelffelntance, with respect Io maxnluiulg radio Communication range, between 300 and 100 klf/. Maximum cunununlcatrorl ranges are sliongls dependent oil the sigiial alleilliatroil sale, ant) Illelclulc on the electrical conductivltles of the coal seam and surrounding ruck. These ranges v;ny tutu about ,,5 Io 100 nleleis Ill a high Iuss scam such as the Ilelllit No. fl to about .100 to 400 meters in a low loss seam such as the Pittsburgh foil portable intrinsically safe radios. The ieslllls die haled on the comparison oftheorc' and experiment for eleven n n. ill sesen coal seams. V OT ate is dice: a conductor such as a power Cable, is present a model has been developed for the coupling of loop antennas to a low loss Coaxial TEM ti;u?smisslon line mode in which the cable acts as the inner conducl,lr and the rock above and below acts as the outer conductor. The electuc and md' nctic Itelds for till` (node are apprlixitllatcly transverse to the cahlC and fall oil expontially with distance in the transverse plane. The principle of reciprocity is used to simplify the analysis. More expelitnental data arc needed to help resolve discrepancies between the theory and the limited data available to date.]

Jan 1, 1980

By J. P. Connell

The U.S. Bureau of Mines awarded a contract to Morrison-Knudsen, Inc., to evaluate the use of roadheaders in underground mining operations. Road-headers were found to be widely used in mines as construction support units, as development miners, and as stoping machines. However, road-headers were found to have mechanical and electrical problems, to suffer reduced productivity when integrated into the mining cycle, and to create dust problems. Also high capital costs and low utilization and avail-ability cause high amortization costs per ton. This report identifies the roadheader operating problems and offers suggestions for improved mechanical and electrical design as well as manufacturer and owner responsibilities for improved availability. The development of a complex integrated excavation and ground support sys tern is no t warranted until the roadheader itself is made much more reliable.

Jan 1, 1980

By Lindsly. Ben E.

"The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2Lewis3 states, ""The estimate of 80 to 90 per cent of the oil left underground does not seem incredible.""It is estimated by the writer that approximately 91 per cent of the oil originally held in the Elliott pool, was still in the formation on January 1, 1924, and that it would take at least 12 years, at the 1923 rate of production, to further reduce this quantity by one per cent of the original content.The progress made in the oil industry during the past few years relative to the prevention of evaporation losses; to improvement in cracking processes, whereby the gasoline yield from many crudes has been doubled and trebled; to the increased recovery of gasoline from natural gas; and many other developments, remarkable as they are, can be applied only to that comparatively small portion of petroleum products which are raised to the surface. A device or process which would cut development costs to one-half would probably result in a much smaller profit to the oil industry, than the profit derived from an additional 10 per cent recovery of the total amount of oil in a pool. Various methods have been used and many others proposed, for the increase of oil recovery from normally depleted sands.In France, oil sands are being mined by means of shafts and galleries. In other places, notably the Bradford, Pennsylvania field, the yield has been increased by means of water flooding, wherein water is introduced into the sand to displace oil, and drive it to producing wells."

Oct 1, 1926

By R. V. Ramani

The industrial hygiene and safety aspects with internal combustion engines in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. This bibliography, therefore, is a compilation of references from interdisciplinary sources pertaining to diesels and related areas. Related areas are defined as those concerned with: (i) mine ventilation system design and operation; (ii) description, measurement, modeling and monitoring of mine atmosphere contaminants, and (iii) tests, standards, selection procedures, and operational practices for internal combustion engines in underground mines. References cited from source materials span the years 1900 to early 1977. Total number of references cited is 511. Subjective criteria governed the definition and selection of references. Therefore, this bibliography is not claimed to be all-inclusive nor does it purport to be an exhaustive search of all sources.

Jan 1, 1977

By G. B. Shea

Among the many engineering problems directly related to conservation in the petroleum industry, that of crude-oil emulsions continues to be important. Emulsions of water and oil always have constituted one of the most serious forms of waste in the oil fields, and the necessity of dehydrating emulsified crude petroleum to obtain marketable or pipe-line oil confronts operators in many fields with a major operating problem. In 1926 the Bureau of Mines published a comprehensive treatise s on oil-field emulsions dealing with field conditions, practical methods of dehydration, and physicochemical characteristics of the formation and resolution of emulsions. Although this bulletin is still available and may be obtained from the Superintendent of Documents, Washington, D. C., and although its contents are a valuable reference on the subject of emulsions, knowledge regarding the physical properties of emulsions and the phenomena of dehydration has increased greatly within the last decade. With the information gained through continued scientific research, substantial improvements have been made in the art of resolving petroleum emulsions. Moreover, in recent years there has been a growing realization of the importance of emulsion-preventive measures that has led to more critical examination of the causes of emulsions and methods of eliminating or at least reducing the degree of emulsification. Conditions causing agitation and commingling of oil and water and the formation of "cut oil" often are within the control of the producer, thereby making it possible to utilize preventive or remedial measures by which emulsification may be minimized or avoided. In fact, many companies have materially reduced their treating costs as a result of careful studies in emulsion prevention and proper handling of "wet" production. Of course, in many instances preventive measures or the correction of conditions causing emulsification cannot be achieved practically or economically, and the emulsions that form must be treated regardless of the care exercised or the money spent in attempting to prevent their formation.

Jan 1, 1939

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By M. W. Von Bernewitz

Because the cutting and polishing of stones are parts of the work of the Bureau of Mines in its study of rocks and minerals and in the determination of specimens sent in for identification, it was decided that a circular covering the subject in a general way would be of practical interest. As several books and periodicals give details of the problems in cutting and polishing, this report will not duplicate their information more than necessary. ACKNOWLEDGMENT The manuscript for this circular was read by Oliver Bowles and Forrest Moyer, Building Materials unit, Bureau of Mines, who supplied some of the illustrations; several photographs were taken by Howard Carl, Optical Section, Bureau of Mines. Equipment firms that y contributed information and publishing houses whose books have been abstracted are mentioned in the text.

Jan 1, 1940