Search Documents

By R. A. Govender, A. Mudau

"Rockbursts continue to be a major contributor to mine accidents and cause of damage to mine excavations, particularly at great depth. The problem of rockbursts has also escalated in civil engineering tunnels driven at depth, due to high levels of in situ stress at such depths. Attempts have been made in the past to mitigate the impact of rockbursts, with rock support remaining the ultimate method for providing stability in rockbursting environments. However, records show that, on many occasions, conventional support elements such as rockbolts, wire mesh, shotcrete, and lacing fail to withstand severe rockburst events.Recently, a support method termed ‘sacrificial’ support was proposed as a potential additional method to prevent rockburst damage, based on observations made after rockburst events in a mine. The philosophy behind a sacrificial support system is that, under dynamic loading conditions, support in the form of a liner must fail; leaving behind, undamaged, what was previously supported rock mass. The sacrificial support concept reported herein is applicable in situations where the source (i.e. seismic event) of the rockburst is located remote from where rockburst damage is likely to occur.Spalling tests based on the split Hopkinson pressure bar (SHPB) technique were conducted to study some aspects of dynamic rock fracturing in tension at high strain rates and the role a sacrificial layer plays in combating dynamic rock failure. A single Hopkinson pressure bar, with a long cylindrical intact rock specimen attached at the bar free end, was impacted by a striker on the opposite free end in order to generate a dynamic stress pulse responsible for spall failure upon reflection from the specimen free end. Different liners and liner combinations were then introduced at the specimen free end as support. Such a simple, yet robust, experimental set-up allowed the potential benefits and failure mechanisms associated with sacrificial support under dynamic loading to be demonstrated and compared with ‘sacrificial support’ behaviour observed in real rockburst events in a mine. Analysis of the results revealed that varying liner thickness and mechanical impedance between rock and support liner play a significant role in limiting rockburst damage."

Jan 1, 2016

By M. C. J. van der Merwe

"Carboxymethyl cellulose is an organic binder used in the iron ore pelletizing industry. The basic principles of how carboxymethyl cellulose (CMC) solutions behave during the pelletizing process and how these principles affect the drop and compression strengths of the pellets are poorly understood. The aim of the investigation was therefore to gain knowledge on the behaviour of CMC during the pelletizing of haematite concentrate.Haematite pellets with different additions of CMC (0.1–0.4 wt%), were subjected to drop tests, compression tests, and free moisture content analysis. The relationship between the drop strength, compression strength, free moisture content, elapsed time, and CMC concentration was analysed.The drop strength had a strong correlation with the free moisture content of the haematite pellets, with a correlation coefficient of 0.94. The compression strength of the CMC-bonded haematite pellets increased as the free moisture content decreased, reaching a maximum upon depletion of the free moisture content. Haematite pellets with CMC concentrations of 0.1 and 0.2 wt% developed most of their strength within the first day after pelletizing, whereas pellets with concentrations of 0.3 and 0.4 wt% developed most of their strength between one and two days after pelletizing. The time within which CMC-bonded haematite pellets develop most of their strength is therefore dependent on the CMC concentration. IntroductionFines are produced during the beneficiation of iron ore. These fines are separated from the lump ore and can be upgraded to produce a concentrate, which is used as a raw material for the production of pellets. Pellets in turn form a key burden material for direct reduction processes as well as the blast furnace (Zhu et al., 2015).Inorganic binders such as bentonite have been used predominantly in the iron ore pelletizing process to obtain pellets with suitable properties (Eisele and Kawatra, 2003). These binders, however, have the disadvantage of introducing impurities into the pellets. This has resulted in organic binders being pursued as suitable replacements for inorganic binders, of which carboxymethyl cellulose (CMC) shows good potential. Although CMC has been used as an organic binder in iron ore pelletizing, the fundamental principles of how it behaves during pelletizing and how these impact on pellet properties are poorly understood."

Jan 1, 2017

By F. A. G. M. Camisani-Calzolari

Approximately 850 groundwater samples were collected over a 29 300 km2 region of the semi-arid Northwestern Cape during the site selection phase of the South African radioactive waste disposal project. The purpose of the geostatistical investigation was primarily to delineate metallogenic occurrences and provinces which might exist below the thin veneer of surficial material and could thus interfere with the suitability of the site, and to quantify the distribution patterns of groundwater parameters in order to establish a relationship to local and regional geology. Up to 34 variables were analysed for each sample. Structural analysis revealed that the study area is statistically uniform. The variables have low correlation coefficients, with the exception of major ions, indicating a general poor degree of interrelationship between the spatial distribution patterns of the different variables. On the other hand, the long semivariogram range of the majority of variables, which reaches 70 km in cases, demonstrates their continuity on a regional scale. Kriging, which was repeated for each parameter, reveals that most variables, particularly trace metals, have distribution trends which are not influenced by local geomorphology or surface lithology. A 50 km wide, 220 km long metallogenic province, defined by kriging, could possibly reflect a broad metallogenic imprint on the basement and could represent a target area for prospecting. Kriging also reveals the possible existence of a wrench faulting system which may well have influenced the Namaqualand coastal graben and the western boundary of the Karoo.

Jan 1, 1987

It is almost eight years to the day when we launched the original SAMREC Code in March 2000. Since that date I think the SA minerals industry has matured beyond recognition in its approach to reserve and resource reporting, and I believe we can be justifiably proud of that progress. Many of those companies that have led the way in reporting standards are listed on our sponsors list. We thank them for their sponsorship but even more for their considerable support in all aspects of the SAMCODE organization. Matt Mullins, my co-speaker here today, has been instrumental in the revision of the SAMREC Code over a long period of time and also took up the reigns with the SAMVAL Code after the retirement of Rob Croll. I would like to formally thank Matt for his immense contribution in producing the two Codes; he can take great pride in the final product and fully deserves the many accolades that we have already received from our international counterparts. He has done all this whilst still maintaining a very demanding day job at BHPBilliton. Matt will be the first to admit that he has received tremendous support from more than 100 people who participated in the various working groups, many of whom are employed by our sponsors. There are obviously too many to mention by name but they deserve a big vote of thanks for their personal contributions. In addition to launching the two Codes we are also launching our ?branding? initiative with our own SAMCODE logo and the SAMCODE website: www.samcode.co.za. All the slides used in the presentation today will be on the website later today as will a newsletter which will serve as a media release.

Jan 1, 2008

By X. Jia

The ability to perform three dimensional imaging at micron-scale resolution of real mineral floc sediments and structures using commercially available Micro X-ray Tomography (XMT) instrumentation can be used for the analysis of aggregates and granules, liberation and dewatering of sediments. This paper presents are view of recent work by the authors relevant to the mining and minerals industries. It covers three main topics: X-ray imaging of agglomerates and multi-component mineralic particles,, permeability of sediments, and dissolution of granules with potential application to heap leaching.

Jan 1, 2008

By Neal Harries

The monitoring of rock slopes is a common procedure in the management of hazards associated with slope instability. Slope stability radar has become widely accepted as the state-of-the-art method for management of hazards associated with unstable slopes in open pit mines. This is confirmed by the rapid adoption of the technology since inception in mid 2003, with over 70 GroundProbe slope stability radars now in use at open pit operations throughout the World. The use of a monitoring system such as slope radar to identify slope hazards is only part of the solution to minimise the consequences associated with slope instability. The presence of the hazard must also be effectively communicated to the mine personnel, so that the correct response to the hazard can be enacted, and the risk mitigated to an acceptable level. In some surface mines, due to the geotechnical characteristics of the rock mass, hazards can develop rapidly; with slopes progressing from stability to ultimate collapse in just hours. In these situations, it is vital that efficient systems are developed to evacuate the area of the pit affected. Such a system has been developed by GroundProbe in South Africa, with the vital driving force for the project being provided by the Anglo Platinum Mogalakwena mine operation based at Mokopane. The mine based development of the system was perceived as an essential aspect in the development of the successful system. From an early stage, the mine provided essential input on both hardware and software developments to allow the system to be rapidly integrated into the mining operation. This paper describes the pit evacuation alarm system that was developed and discussed the benefits obtained from a mine based development program.

Jan 1, 2008

One of the key issues facing gold producers is the management of cyanide and the implementation of the International Cyanide Management Code. Many operations now use cyanide destruction processes to ensure that the material being discharged to the tailings dam is compliant with regulatory requirements and the International Cyanide Management Code. One of the problems for operations is the quantification of both cyanide species and their reaction products throughout the leach and destruction circuits. Therefore methods have been developed utilizing high performance liquid chromatography (HPLC) to measure free cyanide, cyanide complexes of metals such as copper and iron, and other species formed from reactions in leaching and cyanide destruction, including cyanate, thiocyanate, and sulphur species (eg. sulphite, thiosulphate and sulphate). This enables a complete mass balance for cyanide and sulphur in both leaching and cyanide destruction. This paper outlines the methodology which has been developed and discusses the application of these methods in the fundamental research currently being conducted on the impact of sulphide minerals in cyanidation and cyanide destruction chemistry.

Jan 1, 2009

What is the role of The South African Institute of Mining and Metallurgy at a time when so much is developing and changing in South Africa? The minerals industry is represented through employers, employees, government, education, research, public views, and even pure political interests. The role of the Institute is to represent the mining and metallurgical profession. In this role the Institute has aligned itself with Associated Scientific and Technical Societies, the Council of Scientific Societies and the Engineering Association. The Institute is also active on the Engineering Council of South Africa.

Jan 1, 1996

By A. Chiappone, M. Barla, U. Rabagliati, L. Repetto

ABSTRACT: The paper describes the application of both continuum and discontinuum modelling to the study of the stability conditions of the Alpetto mine, a high rock cut located in Cesana Brianza (Italy). The main objective is to provide valuable information for future mine planning and for the assessment of the stability conditions of the abandoned high rock cuts. Continuum modelling involved the applications of the finite difference method, whereas the distinct element method was used for discontinuum modelling. RESUME: L'article décrit l'application des méthodes de modélisation continue/discontinue pour l'étude des conditions de stabilité de la mine d' Alpetto, située à Cesana Brianza (Italie). Le but du travail consiste à determiner des paramètres utiles vis-à-vis du projet et d'estimer les conditions de stabilité de l'amas rocheux au terme de l'exploitation de la mine susmentionnée. La modélisation continue a impliqué l'application de la méthode des différences finis alors que la méthode des éléments distincts a été utilisée pour la modélisation discontinue. KURZFASSUNG: Der Artikel beschreibt die Verwendung der Modellierung von continuum und discontinuum zur Untersuchung/Studium der Stabilitätsbedingungen von der Alpetto Mine, hohe Aushubsfront in einer Felsmasse die sich in der Gemeinde von Cesana Brianza befindet. Das Hauptziel dieser Arbeit ist die Festlegung von Parametern die zur Planung nützlich/behilflich sein können sowie auch die Möglichkeit zur Analyse/Auswertung der Stabilität der Felsmasse-Front nach Aufhebung der Nutzung derselben. Die continuum Methode/Analyse wurde verwendet durch Unterstützung der Finite Differenz Methode da man für die Analyse der discontinuum (Fels als discontinuum beschrieben) der Distinct Elemente Methode verwendet hat.

Jan 1, 2003

By N. B. Devi

The extraction of Cu(II) from HCl media using Cyanex 923 in kerosene was investigated. The effect of shaking time, aqueous phase acid concentration, extractant concentration, chloride ion concentration, various metal ions (Mn2+, Mg2+, Fe2+, and Ni2+), and temperature on the extraction were studied. Using 0.1 M Cyanex 923 the extraction of Cu(II) was 6.7 per cent from 3 M HCl, which increased up to 78.5 per cent with 6.5 M HCl and then decreased due to acid extraction by the extractant. The maximum extraction (97.5 per cent) was obtained with 1 M Cyanex 923 from 5 M HCl solution. A mathematical model has been developed to describe solvent extraction equllibria over wide ranges of concentration of extractant, acid, and chloride ions. The composition of the extracted species has been predicted on the basis of slope analysis results and extraction equilibrium modelling. The negative values of enthalpy change and entropy change confirm the exothermic formation of the extracted complex.

Jan 1, 2012

By K. M. Primrose

Electrical tomography has developed rapidly over the last few years in its sophistication and practical use to enable three-dimensional information on the distribution of phases within flowing mixtures to be observed1. This paper reviews the current state of application from the industrial perspective, drawing on applications case studies based on scaling studies in the laboratory right through to installations on plant. In the laboratory, applications have looked at scale-up of mixing2 processes involving gas-liquid and solid-liquid suspensions3 with a particular interest in verifying computational fluid dynamics simulations or in checking scale-up design4,5. In the processing plant, the circumstances are usually bespoke and may range from simple detection of the degree of homogeneity of a flowing mixture through to the need to measurement a sophisticated batch process such as crystallization, sedimentation, filtering and drying. Examples drawn from the chemical and pharmaceutical industries will be presented and related to the benefits that can be gained through application of the method.

Jan 1, 2008

By F. Trabzuni

Elutriation of solid reactants from fluidized bed reactors can affect their process performance and efficiency greatly. Chlorination fluidized bed reactors for selective conversion of solid metal oxides to metal chlorides are used widely these days. This study provides a platform for a proper understanding of reactant solid characteristics and solid shrinkage interaction with elutriation rate constants using multi-sized particles, sand-like, ?Geldart B? chloridable materials. The study has found that actual elutriation rates of the reactive system are influenced by complex parameters? interaction including bed diameter, reactor freeboard height, bed minimum fluidization velocity, and reactant?s physical properties.

Jan 1, 2009

By M. Le Roux

The dewatering of coal, and particularly fine coal, continues to challenge coal prepatration engineers to find a cost-effective solution. With known world oil reserves being depleted daily, it is envisaged that the future price of coal may justify the use of thermal drying to achieve lower coal product moisture levels. The effect of exposure of the coal to elevated toemperatures on the mechanical strength of the coal was investigated. It was found that temperature does not play a major role in determining the volume breakage of a particle and that other variables such as orientation during impact has a much greater influence. A double breakage mechanism was reported during the grindability tests. Surface, as well as volume breakage, occurs for the first 4 minutes while only surface breakage takes place thereafter. Due to this double breakage action, it was found that exposure to temperature does play a role in the amount of breakage and breakage rates during grindability tests. It was also concluded that a particle will break to an optimum size due to impact, after which only its surface will grind away as it is subjected to breakage forces.

Jan 1, 2008

By M. Kumral

One of the most significant elements in solving the co-kriging equations is the matrix solver. In this paper, the singular value decomposition (SVD) as an equation solver is proposed to solve the co-kriging matrices. Given that other equation solvers have various drawbacks, the SVD presents an alternative for solving the co-kriging matrices. The SVD is briefly discussed, and its performance is compared with the banded Gaussian elimination that is most frequently used in co-kriging matrices by means of case studies. In spite of the increase in the memory requirement, the SVD yields better results.

Jan 1, 2012

By J. Loubser

The concept of caring is in most cases confused with material needs and not psychological needs. By giving employees a job, most managers think that employees should be grateful and return the favour by being loyal, productive and working safely. Other managers hold the view that employees can be lucky to have a job. To show and demonstrate that management are caring for the safety of the workforce requires involvement, dedication and commitment. Obtaining the trust and respect of the workforce should be the main thrust of any organization because within trust and respect lie the secret of optimal safety performance. In the last 70 years, all the fatalities and serious injuries that occurred in the mining industry can be traced back to one thing, non-caring. The same safety non-compliances are still observed, reported and planned against as 70 years ago, and strange as it may sound, the same injuries occur the same way. The question could be asked: Does the mining industry need more risk assessments? More codes of conduct? More engineering. Or does the mining industry need more caring?

Jan 1, 2010

By M. E. C. Snyman, N. Naudé

"Coal fines produced during processing are difficult to dewater and result in a lower quality product and consequent lower value. A South African coal mine experiences severe difficulties with belt filter dewatering operations due to the presence of fines reporting from the thickener underflows. Plant 2 currently handles super-fine particles of size -34 µm and has low belt filter efficiency: excessive moisture retention lowers the product quality and strains downstream processing. It was necessary to determine an alternative method for dewatering these fines. Blending of fine material with coarser material was proposed as a solution. The effect of coal particle size and layering during ultrafines belt filter dewatering was evaluated using various blends of the fine Plant 2 material with coarser Plant 1 material. The best layering arrangement of the two materials and its optimum blend required to achieve reduced filter cake moisture content was determined in practise using a vacuum filter to simulate belt filtration. A blend of the two materials gave improved dewatering efficiency for the belt filters compared with that of the Plant 2 material alone. The best layering configuration was with Plant 2 material at the bottom and Plant 1 material on top. The optimum blend for industrial applications comprised 48% fines from Plant 2. IntroductionFines are produced during the processing of coal. It is estimated that 2 to 3% of run-ofmine coal reports to the ultrafine portion (-100 µm) (le Roux, 2005). The particle size of coal is inversely proportional to the amount of water adsorption, so smaller particles adsorb more moisture. Moisture removal requires either mechanical processes or thermal drying: mechanical processes are less expensive, but the fines still have high moisture retention. Discarding of fines leads to economic losses, so it is essential that they be dewatered so that they can then be sold as a product: fines need to be treated for both resource management and conservation reasons (Kenney, 1994). Removal of free surface moisture from ultrafine coal particles using a belt filter therefore remains a process that needs to be continuously improved. Ultrafine coal originating from a thickener underflow is known to be difficult to dewater owing to factors such as filter cloth blockage and moisture retention due to clogging. Mixing of finer and coarser materials has been proposed to deliver better dewatering efficiency and improved the quality of the recycled water (Kenney, 1994)."

Mar 1, 2019

When designing coal mine roof support, it is necessary to account for the uncertainties and variability that inherently exist within the rock mass and support elements. The performance of a support system is affected by these uncertainties, which are not taken into account in the current deterministic design methodologies used in South Africa. The key to the design of a roof support system is a better understanding of roof behaviour and uncertainties that can been countered during extraction. This paper sets out to develop a method that takes all uncertainties that exist within the rock mass and the mining process into account and provides a quantitative risk-based design methodology.

Jan 1, 2009

By Keith Rowley, Neal Harries, David Noon

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, South Africa, Zambia, Chile and the United States. Greater than 70 rock falls and waste dump failures (from several to millions of tonnes) have been monitored, and on every occasion precursor ?warning? movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines.

Jan 1, 2006

By D. Farrow

Future development of kimberlite mines is now focused on mining at deeper levels. The consequences are increased difficulty and costs of the mining operations. The decisions on investments require accurate resource evaluation and quantification of the risk. In the decision process the first step consists in choosing the number of boreholes sampling the pipe relative to the level of uncertainty that can be accepted. The uncertainty in the volumes of rocks of different types can be assessed as soon as we can estimate these volumes from a given borehole layout and calculate the error by means of its variance for instance. In theory this can be achieved by using geostatistical techniques (‘transitive theory’), but in practice the calculation of the error on volumes can be achieved in very particular cases, assuming some regular sampling patterns. A different approach has been chosen based on simulations, giving maximum flexibility to reproduce the reality of the sampling procedure. The idea is to simulate the geometry of several ‘possible’ pipes with their internal geology and estimate them by kriging. Several experimental errors are obtained on which risk analysis can be performed. The aim is to find a feasible method to perform the simulations with reasonable chance to correctly represent the reality, without data on the pipe extension. The methodology applied is based on some hypotheses that can be assessed by the geologist as well as by the geostatistician. The procedure assumes a geological model based on current knowledge including appropriate geostatistical variation. What make these simulations specific and powerful in this case comes from the fact that the boundaries between the different rock-types can be simulated using a transformation of the real 3D space into a 2D space defined by means of polar coordinates. Ultimate transformations to account for smoother variations with morphological transformations allow the generation of realistic pipe geometries on which sampling pattern can be used to evaluate the estimation errors. By estimating the simulated pipe geometries with different boreholes layouts a risk curve expressing the uncertainty in the volumes of the different rock-types versus the number of holes can be developed.

Jan 1, 2003

By S. C. Greeff

At ISCOR the quantitative determination of the structural properties of coke is done with a Leitz-TAS Image Analysis System. A reflected light microscopic image of a coke sample is converted into a binary image and stored in computer memory or on hard disc. By means of mathematical and stereological techniques the system can transform the images electronically. A lightpen can be used to determine the sequence of these operations. TASIC, which is based on BASIC language, is used as the program language on the computer. The majority of the programs are written by the user to ensure satisfactory results for specific studies. The computer controls the whole system, including the movement of the microscope stage, focusing, transformation and measurement of the image and data processing. The computer is also applied for establishing statistical correlations between the structural and other coke and coal parameters as well as for graphics and predictions of the coke structure. Factors affecting the structural properties of coke are discussed and conclusions are drawn.

Jan 1, 1987