Search Documents

By P. A. Botha

The production of iron and steel generates various types of waste materials containing oxides, carbon, and flux material. Usually, these materials are land-filled at the plant site or are hauled away for disposal. Some of these waste materials are hazardous, and they must therefore be recycled or disposed of properly. The influence of different waste materials in iron-ore sinter blends on the quality and operational parameters in sinter production is described. The recycling of waste materials such as dolochar, scrap fines, mill scale, electric-arc furnace slag, basic-oxygen-furnace mud via the sintering process can achieve a saving in the cost of the raw materials (for example, fuels and flux) and a reduction in pollution. A comparison of a typical sinter with a sinter produced through the utilization of waste materials shows a distinct correlation between certain types of waste material and some metallurgical properties and operational parameters. Dolochar (and arc-furnace slag) in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. In general, dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter, but not necessarily the operational parameters such as the production rate. At Vanderbijlpark, approximately 15 kt of various waste materials per month are successfully recycled in the sinter plant. Investigations into the handling and recycling of other waste materials may indicate that even more waste materials can be utilized.

Jan 1, 1993

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By Q. G. Reynolds

The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single-electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions?this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magnetohydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By A. P. I. Popoola

Aluminium AA1200 was laser alloyed with a combination of nickel and titanium diboride using different weight ratios. Chemical reactions took place with the formation of different phases. The characterization of the alloyed surfaces was carried out by x-ray diffraction (XRD), optical and scanning electron microscopes. The alloyed surfaces are composed of the initial phase of Al-Ni dendrites and eutectics of TiB2/Al and TiB2/Ni distributed on the initial phase. Experimental results obtained showed that Al-Ni intermetallics brought about a significant increase in the hardness property of Al; however, these intermetallics are highly brittle and prone to fail by brittle fracture or stress corrosion cracking when put in service. The addition of TiB2 brought about a reduction in the formation of the seintermetallic phases. A microhardness increase of over 10 times the hardness of the substrate was achieved. Keywords Dendrites, intermetallics, metal composite, Nd: YAG laser.

Jan 1, 2011

By D. Francois-Bongarcon

The ?Poisson effect? is defined and characterized. It takes place even when the material to sample is not liberated. Gy, Pitard, Ingamells, and others, including the author, recommend that a minimum average number of particles of mineral of interest characterize the recommended sample size. How many? Recommended numbers range from 6 to 40 particles depending on authors, corresponding to standard deviations of 41% to 16%. Some guidelines are proposed, and the often alleged ?double-Poisson? effect is examined.

Jan 1, 2009

By A. Morley

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

By P. J. Kinver

This paper deals with the development of backfilling methods and systems at the Broken Hill orebody of Black Mountain Mineral Development Company (Pty) Limited, at Aggeneys in the north-western Cape Province. Production started in 1979, being confined to large diameter blasthole stoping methods in the upper, steeply dipping areas of the orebody. This blasthole reserve is now depleted and the production tonnage, 100000 tons per month, is produced from eight cut and fill stopes in the flatter dipping areas of the orebody. The fill methods of the blasthole stoping area evolved prior to the pillar extraction are briefly discussed together with the resulting experiences gained that enabled virtually 100% extraction to be achieved. The original cut and fill mining used costly hydraulic cemented fill; this was replaced partly by unconsolidated river sand and later by dune sand which occurs in abundance. The paper describes the planning, research work and commissioning of a cycloning plant that now enables dune sand to be used successfully as an unconsolidated hydraulic fill. The development of drainage, placement and control methods are also reviewed.

Jan 1, 1988

By G. W. Healy

The smelting of calcium carbide has always been plagued by eruptions, too often with serious injury y or loss of life. To find their causes, the author calculated an internal energy balance using 1992 data for CaC2 and CaO, and older data for the remaining items. The heat content of the charge, and that of the hot gases formed at the reduction temperature, showed that only a fraction of its heat content can be supplied by these gases. Laboratory data on the electrical resistivity of fine mixtures of coke and non-conductive solids were extrapolated to a commercial carbide charge, and then used to calculate the heat produced by current flowing through the mix from the electrode surface to the hearth, which, under favourable conditions, sufficed to bring the charge to 1900 K and higher, at which temperatures reduction could take place.

Jan 1, 1995

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and down stream processes. In order to take effective measures to reduce their recovery in flotation an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2004

By Q. G. Reynolds

The dual-electrode DC arc furnace, an alternative design using an anode and cathode electrode instead of a hearth anode, was studied at small scale using computational modelling methods. Particular attention was paid to the effect of two key design variables, the arc length and the electrode separation, on the furnace behaviour. It was found that reducing the arc length to brush arc conditions was a valid means of overcoming several of the limitations of the dual-electrode design, namely high voltages and arc deflection.

Jan 1, 2012

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By A. Mitchell

On 25 August 2011, Andrew Mitchell, Lucas Moalusi, and Matthew van der Want of Bell Dewar hosted a presentation on Mining and Communities in Mooinooi, in the North-West Province. The conference was attended by traditional leaders in the North-West Province, officials from the Department of Local Government and Traditional Affairs, and executives from the mining industry. The presentation concerned traditional governance in mining, communities? rights in terms of applicable legislation, and the corporatization of community affairs.

Jan 1, 2012

By K. Cole, D. Mesa, P. Brito-Parada, M. R. van Heerden

Turbulence in mechanical flotation cells, achieved via an impeller, plays a key role in keeping particles in suspension, dispersing air bubbles, and promoting particle-bubble collision. However, studying the hydrodynamics of a flotation cell is not a simple task, due to the complex nature of flotation systems which are opaque, turbulent, multiphase and polydisperse in terms of particle and bubble sizes. In this paper we study the impact of impeller design modifications on the hydrodynamics of a continuously overflowing bench-scale flotation tank. To this end, two different impeller designs, with and without a stator, were assessed using Positron Emission Particle Tracking (PEPT). This allowed the authors to determine, for the first time, the effect of an impeller design on the behaviour of both hydrophobic and hydrophilic particle tracers. It was experimentally observed that the use of a stator modifies the hydrodynamics within the flotation cell, distorting the lower mixing loop that is characteristic of axial impellers. The role of the stator in dissipating turbulence results in reduced particle velocities outside of the impeller-stator region. These results have important implications for flotation cell design and are discussed in the context of the impact that different designs have on particle movement, flotation hydrodynamics and, ultimately, flotation performance. The data set generated is also extremely valuable for modelling and validation purposes. Keywords: Flotation, flotation tank, impeller design, rotor, stator, PEPT, hydrodynamics

Jan 1, 2020

By Sh. Arshadnejad

Stress analysis in a rock medium is essential to determine the stress concentration between two consecutive circular holes and prediction of fracture behaviour. When two consecutive circular holes in a hard rock medium such as granite are loaded internally by the pressure of non-explosive expansion material (NEEM), stress concentration occurs between the holes which then causes the rock to fracture. In this work, finite element (FE) analysis using Phase2 code was employed to study the stress concentration between two consecutive circular holes under internal pressure induced by NEEM. Effects of different hole diameters and spacings, rock properties and NEEM pressures have been analysed. The data gained from the numerical analysis and analytical solutions were then used to develop two models. These models were then modified by using the FE data and polynomial regression analysis. The developed analytical models showed to be in a very good agreement with the FE analysis. Hence, the developed models can be used with confidence to determine stress distribution and concentration factors around two consecutive circular holes in a hard and brittle rock which are loaded internally by the pressure induced from the NEEM. Keywords Finite element method, non-explosive, quarry mining, stress concentration..

Jan 1, 2011

To determine the characteristics of a mineral deposit, the usual practice is to take samples, analyse the properties of those samples and infer the characteristics of the deposit from these properties. This analysis can be done using statistical methods. In the present work we are concerned with two types of statistical approaches, classical statistics and spatial statistics. If one uses classical statistics to represent the properties of the sample values, the assumption is made that the values are realizations of a random variable. The relative positions of the samples are ignored, and it is assumed that all sample values in the mineral deposit have an equal probability of being selected. The likely presence of trends, zones of enrichment, or pay shoots in the mineralization, is ignored. The fact that two samples taken close to each other are more likely to have similar values than if taken far apart is also not taken into consideration. In contrast, spatial statistics will be used if one chooses to consider that the sample values are realizations of random functions. On this hypothesis, the value of a sample is a function of its position in the mineralization of the deposit, and the relative position of the samples is taken into consideration. The similarity between sample values is quantified as a function of the distance between samples and this relationship represents the foundation of spatial statistics. There are few situations where classical statistics can be used. The assumption that all sample values in the mineral deposit have an equal likelihood of being represented will be satisfied only if the sample values are randomly distributed, or if the sample positions are random. Sample values are in fact never randomly distributed within a mineral deposit. Further- more, geologists usually avoid taking samples at random (random sampling), as it is correctly accepted that samples located on a regular grid, or approximately on a regular grid, give more information than randomly located samples. In practice, classical statistics should be used only in the early stages of exploration, when the number of samples available is relatively small and the distances between samples are large. In these circumstances, and whenever the information available is not sufficient to permit the use of spatial statistics, application of the methods described in this chapter is justified.

Jan 1, 1978

To the members of The South African Institute of Mining and Metallurgy I have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 641 to 644 for the year ended 30 June 2006. These annual financial statements are the responsibility of the Institute?s Council members. My responsibility is to express an opinion on these annual financial statements based on my audit. Scope I conducted my audit in accordance with International Standards on Auditing. Those standards require that I plan and perform the audit to obtain reasonable assurance about whether the annual financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the annual financial statements, ?assessing the accounting policies used and significant estimates made by management, and ?evaluating the overall financial statement presentation. I believe that my audit provides a reasonable basis for my opinion. Audit opinion In my opinion, the annual financial statements present fairly, in all material respects, the financial position of the Institute at 30 June 2006 and the results of its operations and cash flows for the year then ended in accordance with generally accepted accounting practice appropriate to the Institute. Supplementary information The supplementary schedule does not form part of the annual financial statements and is presented as additional information. I have not audited this schedule and accordingly do not express an opinion on it.

Jan 1, 2006

By S. Budavari

On the one-hundredth anniversary of the founding of the South African School of Mines, this paper presents a historical review of the tertiary mining education carried out by the School of Mines in Kimberley and the subsequent institutions in Johannesburg. In addition to recording and evaluating a century of mining education, it describes the current activities of the Department of Mining Engineering at the University of the Witwatersrand, which is believed to be the natural successor to the School of Mines. The comparison of earlier and contemporary academic mining activities reflects a gradual transition from the educational philosophy and objectives of a school of mines to those of a modem university department. In the conclusions, some aspects of the educational effort expended during the past hundred years are briefly highlighted.

Jan 1, 1996

By F. J. J. Blaauw

This paper discusses a bold venture into the use of interactive computer graphics technology as the foundation of an overall integrated mining managerial system. The wide range of applications that can be addressed through the use of this technology is highlighted, and some discussion of the major facts of this project, which is still in its early stages, is provided.

Jan 1, 1987

By P. De Kock

Strategic mine planning is concerned with the decisions that determine the value of the business, while tactical planning deals with the tasks to realize that value. When tasked with formulating a strategic mine plan, the mining engineer often turns to commercially available software. However, these software packages have limited applicability to the RBM situation. Adopting a simpler, back to basics approach founded on a deep understanding of the economics of the orebody has the advantage of providing a clear logic to guide tactical planning. By creating a coherency between strategic mine planning, and tactical planning the likelihood of successfully executing the plans and attaining the value promised by the strategic plan is increased. This paper describes the reasons why RBM embarked on a strategic mine planning process, the rationale of choosing the process, and the process itself.

Jan 1, 2007

By Y. Lizotte

This paper describes the design and implementation of the dispatching system at LAB Chrysotile Inc.'s Black Lake Mine Operation, Quebec, Canada. The initial system uses a computer in a passive role, to record and display information in ongoing operations. Simulation studies were undertaken at McGill University to assess various heuristic dispatching rules which can be program- med and inserted into the dispatching system. The computer can then suggest to the operator where a truck should be sent to maximize productivity or improve fleet efficiency. The study stresses the importance of considering the effects of implementing computerized systems on those individuals who must use these systems in their daily work. The roles of individuals from the industry and the university in this joint project are also highlighted.

Jan 1, 1987