Search Documents

The slags produced by the Imperial Smelting Process (ISP) are based on the system ZnO-?FeO?-Al2O3-CaO-SiO2. The slag chemistry is important to the process since it determines the fluxing practice and the operating temperature of the furnace required to produce fluid slag. The paper presents the results of the first systematic experimental investigation of these ZnO-containing slags in equilibrium with metallic iron, and provides information on the primary phase fields and liquidus temperatures in these slags over the range of compositions used in ISP practice. A feature of the slags is the presence of alumina, which has a major influence instabilizing the spinel phase. This information presented in the form of pseudo-ternary sections ZnO-?FeO?-(Al2O3+CaO+SiO2) enabling the data to be readily used by plant engineers. Keywords: liquidus temperature, ISP, EPMA, ZnO-?FeO?-Al2O3-CaO-SiO2, phase equilibria.

Jan 1, 2004

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

Historically, mine ventilation practices as it was referred to then and which was enforced by legislation of those days, focused primarily on the conditions in the working place and little attention given to actual exposures of workers to contaminants in the working environments. With the advent of the Leon Commission of Inquiry into Safety and Health in the South African Mining industry in 1994, findings in the report indicated that more attention should be given to occupational health of workers. The upshot of this report resulted in the promulgation of the new Mine Health and Safety Act (MHSA) with certain sections of it devoted to all the aspects of occupational medicine and occupational hygiene. This paper describes the present situation with regards to statistics on occupational hygiene performance and compensation paid out to persons who have contracted occupational diseases, as well as the way forward in terms of legislation implemented in September 2002 on the chronic and acute issues affecting the mining industry in SA.

Jan 1, 2003

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By J. S. Harington

Our purpose is to record and to explain the widely changing numbers of the huge total of black workers on the gold mines of South Africa over the century from 1896 to 1996. These men were recruited from up to twenty territories, and their contributions are examined. The major areas providing labour over this long period have been Lesotho, the former Transkei within South Africa and Mozambique. From 1989 to 1996, for instance, these three areas accounted for over sixty per cent of the total labour force (tlf). Our principal Figure 1 shows the tlf fluctuating through time to reach a peak of 480 000 in 1988. Irregular falls are also documented with the most serious in 1995 to 180 000. Based on this graph we consider the political, economic, sociological and historical reasons behind these changing employment opportunities. These have included external world-scale events such as war or depression, as well as internal changes of national economy and policy. We show the importance for numbers employed of the discovery of gold in the Orange Free State in 1946, the influence generally of the ?Winds of Change? and the firm maintenance by the State of law and order. Varying gold production costs and profitability against high tax rates, allied with increasing wages and a lack of development capital, have led in the last decade to employment falling by fifty per cent, despite an actually higher value of gold output. Finally, this analysis considers the role of the migrant labour system as it affects, and is affected by, conditions in the gold mining industry, with special reference to its less than humane consequences in the numerically dominant territories of Lesotho and Transkei.

Jan 1, 2004

By Y. D. Lee, J. H. Park, D. S. Kim, H. S. Song

The viscosities and the infrared spectra of the CaO-SiO2-MgO-CaF2(or Al2O3) slags were measured to enhance our understanding of the interrelationship among the thermophysical property, microscopic structure, and chemical thermodynamics of molten slags. The structural role of CaF2and Al2O3in the calcium silicate melts can be explained by a change of the degree of polymerization (DOP). The effect of CaF2on the viscous flow of molten slags is based on a decrease in the DOP by F-as well as by O2-ions and this was confirmed by the infrared (IR)spectra of the quenched slags. The effect of Al2O3on viscosity increase can be understood from an increase in the DOP by the incorporation of the [AlO4]-tetrahedra into the [SiO4]-tetrahedral units and this was also confirmed by the IR spectra. An amphoteric behaviour of Al2O3in the aluminosilicate melts could be correlated to the effect of ionic species of alumina, that is [AlO4]-tetrahedra and [AlO6]-octahedra, on the stability of silicate polyanions by taking the activity coefficients of slag components into account. Keywords: viscosity; infrared spectra; degree of polymerization; amphoteric behaviour; stability; activity coefficient

Jan 1, 2004

The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization. Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ?old hands? are retiring and cannot easily be replaced due to limited graduation numbers. Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries.

Jan 1, 2014

By N. Henderson, J. Weyer, J. F. Brune

"The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization.Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ’old hands’ are retiring and cannot easily be replaced due to limited graduation numbers.Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries."

Jan 1, 2014

By Ö. Uysal

This study deals with the presentation of the mechanized longwall mining project introduced some years ago to increase productivity and output of Aegean Lignite Establishment (ELI) owned by Turkish Coal Enterprises (TKI.) and the comparison of this method with a planned alternative new mining method called ?shortwall mining? where continuous miners will be introduced as primary coal excavation machines. Following the planning phase, production costs have been calculated for both mining methods on the basis of a panel having a height of 7.5 m. In addition to cost analysis, both methods have been evaluated using ?the multi-dimensional objective system?. In this evaluation the value synthesis has been carried out according to scoring models. Lastly, the advantages and disadvantages of both production methods have been stated by analysing them according to related criteria. In the light of outputs gathered from the analyses, it has been determined that the shortwall mining method will out perform the longwall method. Keywords: continuous miner, shortwall mining, longwall mining, multi-dimensional objective system.

Jan 1, 2006

A mining engineer from South Africa, whose research has taken him to some of the world?s deepest gold mines, is the winner of the St Andrews Prize. Daniel Limpitlaw, 27, picked up a cheque for $25,000 for his dissertation on reversing the damage done by early mining technology, which he claims is partly responsible for blighting the urban environment in many South African cities. Launched in October 1998 by the University of St Andrews and international energy company Conoco, the St Andrews Prize sought practical solutions to environmental problems. It attracted interest from 450 individuals and groups from countries as diverse as China, Pakistan, Canada, New Zealand, Germany, the UK and the United States.

Jan 1, 1999

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Ground probe?s slope stability radar has enabled the Harmony open pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By M. Verri

[ ]

Jan 1, 2009

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

By C. Musingwini

Traditionally, mineral reserves management at most underground mines in Zimbabwe focus on maintaining large mineral reserves so that the time between development and production is as long as possible. Historical data at Shabanie mine, a Zimbabwean sub-level caving underground mining operation, confirms this practice. However, the high cost of underground development means that the luxury of large buffer mineral reserves cannot be justified. Furthermore significant increases in the costs of production, exacerbated by the current unfavourable economic climate, make the wisdom of extending development workings well ahead of use questionable. Poor ground conditions at Shabanie mine, mean that some development ends have to be re-mined two or three times due to partial or complete closure between the time they are mined and the time they are utilized. In order to reduce the inordinately high support costs associated with closure of development ends a new ?just-in-time? (JIT) approach that provides development ends as and when they are needed, has been adopted. Accordingly a model to determine an appropriate ?just-in-time? rate of development has been created. The JIT development model indicated that the mine could reduce development rates from 330 m/month in 2001, to 160 m/month in 2002 and achieve savings of about 50% on annual support costs, but still assure customers of a long-term product supply. The mine accepted the model in November 2001 and began implementing it in 2002. Results of the implementation will be reviewed in 2003.

Jan 1, 2003

By M. Tanaka, K. Aoki, T. Mori, H. Morioka, K. Iwano, T. Kanagawa

To estimate the detailed characteristics of the rock around the cavern during excavation, new monitoring technique for dynamic properties of the rock has been applied. In this paper, micro-seismic monitoring and AE monitoring technique are applied to the excavation of large underground rock cavern and the result was discussed to clarify the acutal behavior of EDZ around the cavern. Zur Einschätzung der Gesteinseigenschaften um die Ausschachtung herum haben die Autoren eine Technik eingesetzt, mit der die physikalischen und dynamischen Änderungen im Gestein um den Schacht während der Ausschachtung beobachtet werden. In der vorliegenden Studie wurde zur mikroseismischen Überwachung ein AE Überwachungsverfahren eingesetzt und die Autoren berichten über die Veränderungen in den Gesteinseigenschaften um die Ausschachtung herum. Dans le but d'évaluer en détail les propriétés des roches qui forment les parois des cavernes creusées, les auteurs ont utilisé une technique de mesure permettant d’observer les modifications physico-dynamiques des roches aux alentours de la caverne pendant son excavation. Dans le cadre de cet article, une technique de surveillance de l’agitation et du bruit microséismiques a été mise en œuvre et les auteurs font état de la modification des propriétés de la roche environnante.

Jan 1, 2003

By L. I. Gonzalez de Vallejo

SRC rockmass classification have been applied to 25 tunnels in Spain and Italy, for which it was found that much heavier supports than those estimated by the RMR index were required. SRC and RMR indices and other relevant geomechanical data were obtained during the site investigation and construction stages. Data corresponding to in situ stress measurements, analysis of tectonic structures, and instability problems arising during construction were used to asses the state of stress. The relationship between tunnel section convergence and the SRC and RMR indices was also analysed. Support measurements based on SRC and RMR classification were compared with those actually used during construction. These analyses indicate that for most of the tunnels examined, supports estimated using the SRC were much closer to those actually installed than those predicted by the RMR index. Bei der Verwendung des SRC-Systems zur Klassifizierung des Gesteins als Baugrund für 25 Tunnel in Spanien und Italien wurde festgestellt, dass viel schwerere Abstützungen benötigt wurden, als wenn die Beurteilung anhand des RMR-Systems angefertigt würde. Die Klassifizierung anhand des SRC- und des RMR-Systems, sowohl als auch andere wichtige geomechanische Daten wurden während des Ablaufs der Erkundungen und der Bauausführung gewonnen. Die Resultate der Messungen der Spannungen vor Ort, die Analyse der tektonischen Struktur und die Stabilitätsprobleme während der Bauausführung wurden dazu verwendet, um den im Felsgrund vorherrschenden Spannungszustand zu definieren. Das Verhältnis der Messungen der Tunnelkonvergenz zu dem SRC- und RMR-Index wurde auch analysiert. Die durch das SRC- und RMR-System vorhergesagte Grösse der Abstützung wurde mit der Grösse der Abstützungen verglichen, die am Bau letztlich verwandt wurden. Diese Vergleiche zeigen, dass für die meisten der studierten Tunnel die Vorhersage der Abstützungen, die anhand des SRC-Systems angefertigt wurden, viel näher der wirklich verwendeten waren als die Vorhersage anhand des RMR-Systems. SRC rockmass la classification ont été appliqué à 25 tunnels en Espagne et l'Italie, pour laquelle il a été trouvé que des appuis beaucoup plus lourds que ceux évalués par l'index RMR ont été exigés. SRC et des index RMR et d'autres données geomechanical appropriées ont été obtenu pendant l'enquête de site et les étapes(scènes) de construction. Les données correspondant aux mesures de stress(d'accent) in situ, l'analyse de structures tectoniques et des problèmes d'instabilité surgissant pendant la construction ont été utilisées aux ânes(culs) l'état de stress(d'accent). Le rapport entre la convergence de section de tunnel et le SRC et les index RMR a été aussi analysé. Les mesures d'appui basées sur SRC et la classification RMR ont été comparées avec ceux en réalité utilisés pendant la construction. Ces analyses indiquent que pour la plupart des tunnels examinés, les appuis évalués utilisant le SRC étaient beaucoup plus proches de ceux en réalité installés que ceux prévus par l'index RMR.

Jan 1, 2003

Due to the reduction in frictional resistance, the characteristics of joint infill have a major role to play on rock mass instability. This paper elucidates the laboratory behaviour of graphite infilled joints based on a large-scale shear apparatus under constant normal stiffness (CNS). Discontinuities in a graphite mine have been simulated using high strength gypsum plaster, with the joints infilled with compressed graphite layers. The Fourier series was employed to characterize the joint surface, and the method of using the Fourier coefficients for the prediction of dilation and normal stress with displacement is explained. Die Charateristik von Verbindungsfüllungen hat einen wichtigen Einfluss auf Felsmassenstabilität aufgrund der Verringerung des Reibwiderstandes. Diese Veröffentlichung untersucht das Verhalten von Graphit gefüllten Verbindungen im Labormaßstab mit einer Methode die auf einem gross-umfang Apparateprinzip unter konstanter Normal-Steifheit beruht. Unregelmässigkeiten in einer Graphit Mine wurden mit Gypsum Gips von hoher Festigkeit simuliert, die Verbindungen wurden mit kompressierten Graphitschichten gefüllt. Fourier Reihen wurden angewandt um die Verbindungs Fläche zu Characterisieren. Die Methode die verwendet wurde um die Ausdehnung und Normalkraft mit der Verschiebung mit Hilfe von Fourierkoeffizienten zu bestimmen wird beschrieben. Due à diminution des résistances par frottements, les caractéristiques des joints de remplissage joue un rôle majeur sur les instabilités de la roche. Cet article étudie le comportement en laboratoire des joints de remplissage en graphite à partir d’un dispositif de friction à grande échelle sous rigidité normale constante. Les discontinuités dans une mine de graphite ont été simulées grâce à un plâtre à haute teneur en gypse, dont les joints ont été remplis de couches de graphite compressées. La caractérisation de la surface des joints a été réalisée avec les séries de Fourier. La méthode utilisant le coefficient de Fourrier pour la prédiction de la dilatation et de la compression en fonction du déplacement est également expliquée.

Jan 1, 2003

By G. Laing

On scheduled commissioning and effective operation of a solvent extraction circuit relies on getting the design of both the core contact equipment and the peripheral plant right. Experience has shown that poor performance of new plants is frequently a result of ?utility? systems that do not match the requirements of the circuit, rather than the mass transfer equipment itself. Both the operator/owner and designer need to understand the ?complete requirements? for the circuit to get the balance of the design right. This paper reviews generic issues, frequently overlooked or altered during cost-cutting exercises, which have a significant impact on plant performance.

Jan 1, 2002

By T. Dlokweni

Several Rockmass classification systems have been developed and used in Civil Engineering design and for underground mining operations. Some of these rockmass classification systems have been modified and used in the South African coal mining industry to quantify descriptive geological information for use in coal mine design and roof support selection. The Coal Mine Roof Rating (CMRR) system developed in the USA has been investigated in detail as part of the study. Advantages and disadvantages of the system have been identified by means of underground and surface borehole testing. Investigations into the rating systems in South Africa found that most of the rating systems used in the South African coal mining industry are for planning purposes, and are conducted on borehole cores. This study also highlighted that the rating systems being used are based on geology, and that the human factor plays a major role in the rating systems. To overcome these problems, all the classification systems used in South African coal mines have been benchmarked against impact splitting technique and documented. The best elements of these systems are combined into a new standard system that will be easily used by all mine geologists and rock mechanics engineers. Plusieurs systèmes de classification de la masse rocheuse ont été développés et utilisés dans le Génie Civil et pour les opérations d'exploitation minière souterraine. Certains de ces systèmes de classification de la masse rocheuse ont été modifiés et utilisés dans l'industrie minière sud-africaine pour quantifier l'information géologique descriptive utilisée dans la conception de mines de charbon et la sélection de soutènement du toit. Le système d'Evaluation de Toit de Mine de Charbon (CMRR) développé aux USA a été examiné en détail, comme part de l'étude présente. Tests en surface de trous de mine ont permis d'identifier les avantages et inconvénients du système. Une étude des systèmes d'évaluation en Afrique du Sud a révélé que la plupart des systèmes d'évaluation utilisés dans l'industrie minière sud-africaine sont utilisés pour la planification, et sont menés sur les carottes de trous de mine. L'étude présente a aussi souligné que les systèmes d'évaluation utilisés sont basés sur la géologie, et que le facteur humain joue un rôle majeur dans les systèmes d'évaluation. Pour surmonter ces problèmes, tous les systèmes de classification utilisés en Afrique du Sud ont été référencés en termes de technique de fissuration sur choc, et documentés. Les meilleurs éléments de ces systèmes sont combinés dans un nouveau système standard qui sera utilisé aisément par tous les géologues de mine et les ingénieurs miniers. Verschiedene Gesteinsmassenklassifikationssysteme wurden entwickelt und kamen im Design für Hoch- und Tiefbau und Untertageabbau zum Einsatz. Einige dieser Gesteinsmassen-klassifikationssysteme wurden modifiziert und sind in der südafrikanischen Kohlebergbauindustrie in Verwendung, um beschreibende geologische Informationen für die Anwendung im Design von Kohlebergwerken und der Firstabstützungsauswahl quantitativ zu beschreiben. Das in den USA entwickelte Kohlengrubenfirstbewertungssystem (CMRR) wurde als Teil der Studie im Detail untersucht. Vorteile und Nachteile des Systems sind mittels der Untergrund- und Oberflächenbohrlochprüfung gekennzeichnet worden. Prüfungen der Bewertungssysteme in Südafrika ergaben, daß die meisten Bewertungssysteme die in der südafrikanischen Kohlebergbauindustrie benutzt werden, Planungszwecken dienen und werden anhand von Bohrlochkernen durchgeführt. Diese Studie hob auch hervor, daß die verwendeten Bewertungssysteme auf Geologie basieren und daß der menschliche Faktor eine Hauptrolle in den Bewertungssystemen spielt. Um diese Probleme zu überwinden, wurden alle in südafrikanischen Kohlengruben benutzte Klassifizierungssysteme vergleichsweise in Hinblick auf Spaltschlagtechnik überprüft und dokumentiert. Die besten Elemente dieser Systeme werden in ein neues Standardsystem kombiniert, das leicht von allen Grubengeologen und von Gebirgsmechanikingenieuren benutzt werden kann.

Jan 1, 2003

By R. P. H. Willis

Uranium is back on the radar. Uranium has always been a controversial metal, from its role in the arms race to its claim to be the only viable alternative to fossil fuel. This paper will cover its properties and use, its occurrence and production in South Africa, the current market drivers and its future role as a primary energy fuel. It will highlight the difference between uranium used to make a bomb and uranium used in a power station. The recent significant uranium price rise will be put into context of the market drivers including geopolitical issues. Planned expansions in nuclear power station capacity will be reviewed, as will new mine production. Future demand will also be speculated on.

Jan 1, 2006