Search Documents

By P. K. Berger, G. T. Lineberry, H. P. Cole, J. V. Haley

Sixty-five simulation exercises were developed for teaching and testing problem solving and decision making skills to miners and mining engineers. The exercises focused on judgment and decision making for preventing and controlling mine emergencies. The structure and field testing of the exercises are described, and sample frames of individual exercises are presented. Empirical data are summarized about the effectiveness of these simulations based on the performance scores of a national sample of miners and mining engineers.

Jan 1, 1994

By F. F. Peng, D. C. Yang, G. Yanief, E. H. Cho

This study deals with carrier flotation of cerium dioxide, a surrogate of plutonium oxide, which is the major contaminant at the Nevada Test Site (NTS). The objective of this study was to determine the feasibility of using carrier flotation for remediation of the site. In this study, a - 200-mesh fraction of pure cerium dioxide was used. Oleic acid was used as the collector, while calcium carbonate was used as the carrier. Mechanical-cell tests were conducted to float the surrogate from a mixture containing uncontaminated NTS soil, both in the absence and presence of the carrier. It was found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34% to 65% by adding only 0.5% calcium carbonate (-150 mesh). The recovery further increased to 95% by adding 10% calcium carbonate. The flotation method utilizing a carrier of calcium carbonate seems to have a high potential for the remediation of the soil contaminated with radionuclides at the NTS.

Jan 1, 1998

By Robert L. Cascio

The mining industry uses a large amount of electric power. Their equipment is subject to extreme environmental conditions and mechanical shock. A significant number of electrical accidents are a result of improperly grounded electrical equipment. Federal regulations require the safety ground bed resistance to be measured once a year or after modifications. Most commercially available instruments used to measure the ground bed resistance require the ground conductor to be disconnected and the power system disconnected for safety reasons. The "fall of potential1' method requires auxiliary ground rods and approximately two hours to complete the test. Although a new instrument was initially thought to measure the ground bed resistance immediately without isolating the ground bed, field tests have shown this method is not accurate. In some cases, a continuous measurement of the ground resistance is desired. A monitor has been developed and is presently being evaluated at several mines. These installations will be discussed.

Jan 1, 1992

By W. L. Han, Y. D. Zhang, X. C. Li

Meta-systhetic technique for large systems engineering has been placed on the agenda. The meta-systhetic A1 approach should involve the integration of digital and knowledge info, from qualitative to quantitative analysis, etc. Some algorithms of meta-systhetic technique such as ANN-ES and GA-ANN are introduced. A case study follows - mining conditions evaluation by meta-synthetic A1 methods, including: setting up the structure of evaluation indexes system, deciding their grade of membership by ANN-ES algorithm; determining the weight values of evaluation factors by GA-ANN algorithm; and developing the integrated evaluation model.

Jan 1, 2002

By Gemei Yang, Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

Laboratory tests on controlled airflow recirculation have shown the development of transient states in response to changes in system prevailing conditions such as those generated by a sudden start-up and stoppage of fans. Researchers in many European countries have developed various models to explain these phenomena. However, these models failed to consider some important factors such as diffusion and dispersion of gas in turbulent flows. For both in-line and cross-cut recirculation, tests have shown that after the start- up of a booster fan, the gas concentration in the system fluctuates, reaching high levels at the initial states and slowly dying out with time. These fluctuations cannot be represented adequately by simple step-wise functions but rather by smooth, albeit complex equations. In this paper, the phenomena are explained by the convection-dispersion theory, and represented by a mathematical model. Based on a few simplifications and applying Fourier's Transform Method to the differential equations of the flow recirculation model, an integral form of gas concentration function was derived. The Simpson Integration Method was used to compute numerical results for two laboratory tests. The paper also discusses the range of the dispersion coefficient to improve the accuracy of the model.

Jan 1, 1989

By Sharon G. Roness

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their: coal. Sulfur was the major concern. Btu content and sodium limited the market for some plants. The PRB market has now extended to plants that are converting from other coals because of the Clean Air Act. These new customers are more sensitive to constituents that affect boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to improve cost controls. Kerr-McGee Coal's Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998

By S. Tuylu, D. Adiguzel, A. Bascetin

"Optimization techniques are successfully used in many different fields such as engineering, physics, economy, and politics in order to enhance the performance of the systems. In concrete technology, Aggregates are prepared by mixing the water and cement in proportional quantities. In order to obtain desired quality control parameters, the determination of the ingredients ratios is one of the important problems for the optimization. Additionally, in the quarries where the aggregate quality constantly changes, blending optimization must be made to obtain a sustainable aggregate quality. This study showed that linear programming, which is easy and which includes many aggregate properties, cannot be used in terms of some aggregate properties. Therefore techniques such as nonlinear programming or genetic algorithm must be used. INTRODUCTION Concrete is a used construction material and made by mixing the aggregate, cement, and water. The concrete properties are directly related to the properties of these materials in blending. The quantity of aggregates in concrete is approximately 70 percent of the concrete’s volume. Therefore, the most important material is aggregates. The extraction of aggregate materials in quarries is more problematic because of variable bedrock properties. Therefore, the quality of the materials changes and the characteristics of the concrete are also influenced directly. In terms of sustainable use of natural resources, produced aggregate materials which have different qualities should be used optimally (Adiguzel et al., 2014). Nowadays, in the solution of the blending optimization, various optimization techniques are being used such as linear programming, nonlinear programming, and genetic algorithm. In this study, blending optimization techniques especially used for concrete aggregates blending have been summarized, and the advantages and disadvantages of these techniques have been introduced. BLENDING PROBLEMS Blending is a frequently encountered problem in process-type manufacturing such as mining, refinery, food industry, chemical industry and metal industry (Sakalli 2010). Blending is a commonly used method in lots of practical solutions (Sarker and Newton 2008). Several optimization techniques are available for blending problems (Furman and Pardalos 2009). The most important issue is to blend with minimum cost. The blending problem is a special linear model which was developed to solve this problem. In blending optimization research, linear programming is a widely used method (Adiguzel et al. 2011; Bascetin and Adiguzel 2011)."

Jan 1, 2016

By A. I. Kalugin, A. A. Abramov, D. E. Kozlov

As a result of thermodynamic analysis of a mineral-sodium, oleate-water system, flotation and adsorption tests at various pH values, and sodium oleate concentrations, it has been established that due to regularities of phosphate-containing minerals (fluorapatite, hydroxyapatite, carbonatapatite) flotation cannot be explained by the formation of alkali-earth metal oleates on their surface. This paper presents a novel theory that connects optimal conditions for mineral flotation with zero charge of its surface, which can explain the regularity of minerals flotation observed. The quantitative physicochemical flotation models developed based on the theory are suitable for improving industrial processes, conditioning of recycling waters, and application in automatic control systems at the plants. Key words: apatite, oleate, flotation, modeling, control, and regulation.

Jan 1, 1999

By T. Y. Yan

An effective elution technique has been developed for recovering uranium from ion exchange resins loaded in the carbonate leaching process. The procedure employs direct elution with acid. In comparison with conventional base elution, the procedure yields eluate of higher uranium concentration, results in a more complete elution, keeps the performance of the ion exchange resin at the fresh stage, reduces acid consumption, eliminates carbonate consumption, and reduces waste for disposal. The technique has been successfully demonstrated in the field and patented. It lends itself to commercialization.

Jan 1, 1987

By S. L. McGill, P. B. Comba

Many gold producing states are requiring rinsing of spent heaps to render the leached ore compatible with the environment and are placing reatrictiona on effluent pH, cyanide, and metals concentrations. Parameters which may affect efficient rinsing of heaps have been investigated by the U.S. Bureau of Mines in laboratory column studies. Rinse profiles for cyanide, metals, and pH as a function of the volume of water passed through the spent ore are presented. Fresh water rinsing of spent ore in columns showed that rinsing of cyanide was not affected by the rinse solution application rate. Interrupted rinsing with a rest period between applications reduced the volume of water required to meet effluent cyanide concentrations. Chemical oxidation of the effluent with recycle of the rinse solutions reduced effluent cyanide concentrations and the volume of waste solution generated. Water rinsing was not successful in reducing the alkalinity of the cement agglomerated ore. A dilute acid solution had to be applied after cyanide removal to reduce effluent pH levels to specified limits.

Jan 1, 1991

By P. K. Davis, B. Gharib

The results of a previous basic study of the flow and design characteristics of hydrocyclones demonstrated that a recovery as high as 99% with a product rating* of 0.95 can be achieved on a batch+ basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-¬cyclone system was sponsored by the US Department of Energy, which also sponsored the initial study. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1990

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By D. D. Misra

The paper presents a computer simulation package developed for the size¬-reduction circuits of Indian hematitic iron ores. The package is developed by linking independent procedures describing different unit operations like crushing, screening, recycling, etc. Mathematical models are used to quantify the unit operations involved. The models are selected after thorough analytical studies of the samples and data collected from four operating plants. The package developed gives a fairly accurate result with respect to, size and chemical composition of the flow stream and products. The program written in PASCAL can be used to try the flowsheet with various raw ores, as well as different flowsheets with the same raw ore.

Jan 1, 1989

By Rashi Tiwari, George Danko, Jeremy Knowles

A control technique is described for enhancing the efficiency of materials handling and other mining operations. The concept involves human-operator and robotics control interactions to assist in mining operations. Many mining tasks require a human operator to coordinate the motion of several machine links by simultaneously manipulating multiple joysticks or other control devices. The new control architecture allows for automatic coordination of multiple machine joints. The machine movement may follow a computer-optimized, learned coordination pattern, while the operator still retains the master control of the overall trajectory and velocity parameters. Examples are described for a surface mining front shovel.

Jan 1, 2005

By F. F. Peng, Z. Lu

Employing a combination of two types of polyelcctrolyte might become necessary to enhance both the settling rate of the flocs and the water clarity of a fine-particle suspension in a high-capacity thickening process. The sequence of addition, mixing, type and dosage of polymer all affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance, i.e., a high settling rate of the flocs and the deisired underflow density and overflow water clarity. The required performance can be achieved by either adjusting the pH prior to anionic polyelectrolvte flocculation or using a combination of polymer flocculant and coagulant (dual-polymer system). The dynamic thickening test results showed that only the approach using a dualpolymer system is capable of meeting the required performance. The effects of polvelectrolvte dosage, the sequence and numbers of polyelectrolyte addition, the feed concentration, the bed level and the rake speed on the settling rate, underflow percent solids and water clarity were studied in cylinder tests and in a laboratory dynamic thickening unit. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively using total suspended solids in supernatant, underflow density and capacity per unit of settling area per unit of time. The objective of this study was to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1999

By Kal V. S. Sastry, Stephen N. Little

Computer simulation of comminution systems is found to provide significant cost savings by enabling efficient circuit design and development of control systems. These simulation systems are based on sound mathematical models and numerical methods. Nevertheless, they are found to be hard-to-use and hard-to-modify to carry out more elaborate process analysis. This paper discusses the fundamental principles and practical aspects of an advanced, highly functional, and user-friendly SIMulator for COMminution, SIMCOM, that is being developed at Berkeley by incorporating state-of-the-art software engineering principles.

Jan 1, 1992

By Robin J. Batterham, Dave J. Robinson

The most significant trend in flotation has been the ever-increasing scale of operations. There is, however, doubt that this ongoing trend is enough to maintain the economics against trends such as falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. We comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 to 20 years, but in the meantime the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation as we know it will change significantly. 

By Jim V. Rouse

The mining, beneficiation, and processing of phosphate rock in the Florida phosphate district constitutes a large portion of the southeastern mining industry. For example, 1973 production is reported to have been approximately 35 million tons of phosphate rock (Guimond and Windham, August 1975) and production has increased to over 45 million tons in recent years. The 1973 activity involved the movement of approximately 127 mil lion tons of material. From the hydrologic standpoint, this mining and beneficiation requires the dewatering of ore horizons, pumpage of large quanitites of water for mining and processing operations, and the entrainment of immense quantities of water in waste slurries. Also of significance is the fact that the cited 1973 production involved the disruption of approximately 3200 curies of radium and over 6000 curies of uranium. Much of this material reported with waste products, with the potential for contamination of area ground waters. However, natural removal mechanisms active within the area have generally been effective in preventing significant contamination of the ground-water resource.

Jan 1, 1983

By R. J. Sweigard

Fine coal refuse is often pumped, as slurry, into surface impoundments as a means of permanent disposal. As the available volume is filled, the height of the embankments are frequently increased. Many times the additional embankment material is placed upon consolidated fine coal refuse. There has been some concern about the long-term effect of consolidation of this material at or above the liquid limit upon its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from Central Appalachian coal preparation plants. The refuse was consolidated in 10-foot plexiglass columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart and triaxial tests were performed on both the consolidated material and unconsolidated material for comparison of their shear strength parameters.

Jan 1, 1997