Search Documents

By Don Opacic

The disposal of sludges and other similar industrial wastes is a major problem. Liquid wastes from industrial operations, when treated, produce significant volumes of sludge which are difficult to dispose of, because of the chemical and physical properties of the sludge. In the mining industry sludge is produced from various water treatment operations, in particular mine drainage neutralization. Waste water from coal preparation plants also produces a sludge however the sludge is in fact a slurry containing clays, coal fines and coal impurities. In many areas the disposal of these sludges is producing a serious problem. Mine drainage sludge consists of a variety of hydrous iron oxides, usually ferric oxides, contaminated with other neutralization products such as calcium sulfate. The volume of sludge from mine water or mine

Jan 1, 1973

By Robert A. Westin

Polychlorinated biphenyls (PCBs) are a group of chlorinated chemicals that were used in many different fire resistant hydraulic fluids, heat transfer fluids, and in electrical equipment as dielectric liquids. PCBs were manufactured primarily by Monsanto Chemical Company under the tradename Aroclor, and were used by many different electrical equipment manufacturers. PCBs are noted chiefly for their extreme chemical inertness. This resulted in exceptional fire resistance and long life in applications involving exposure to high temperatures and intense electrical fields. This combination of properties resulted in PCBs being widely used in electrical equipment used in mines, including transformers, capacitors, and some electric motors. PCBs were also used as working fluids in some heat transfer and hydraulic sys terns. The same chemical resistance that gave PCBs long life in industrial applications give PCBs essantially eternal life when they are released into the environment. PCBs are not highly toxic in the sense that exposure does not cause immediate health problems. However, PCBs accumulate in the human body and neither degrade nor are eliminated from the body, and long-term exposure to PCBs can result in changes in liver function which may increase susceptibility to the carcinogenic effects of other chemicals. PCBs also accumulate in the food chain; the concentration of PCBs in fresh water fish may be several hundred thousand times as high as in the water the fish are taken from.

Jan 1, 1981

By K. Ohga, V. J. Hucka

The presence of methane gas in mines creates hazards of explosions, fire and suffocation. Under certain conditions the occurrence of methane also poses a danger of gas and coal outbursts. Consequently, prevention of gas and coal outbursts in coal mines requires a sound knowledge of methane gas occurrence in mine workings. However, the direct method of determining methane content of coals developed by the U.S. Bureau of Mines is time and labor consuming for measurement, a new transportable methane tester was developed for Japanese coal mines. The instrument automatically measures emission gas from coal samples in the underground and also records and stores the data. Back on the surface, the tester can be connected via a RS 232 port to a PC computer for methane content estimation. Details of this technique are described here. Results on methane content determined in Japanese and U.S. western coal seams are discussed, as well.

Jan 1, 1991

By Jean-François Boucher, Ernest K. Yanful, Mei Lin Shelp, Lionel J. J. Catalan

Shallow water covers for preventing acid production in tailings are based on the principle of minimizing oxygen availability. Resuspension of material from the tailings bed may result in increased oxidation and metal releases since dissolved oxygen is at near saturation levels in the water cover. Resuspension can be caused by waves and currents strong enough to mobilize the surface of the tailings bed. Tailings resuspension was measured with sediment traps in the Upper Cell of the Heath Steele site near Mirarnichi, New Brunswick Canada. Although significant amounts of resuspended tailings were collected in all traps, analysis of resuspended solids and bed tailings suggests that for the observed wind conditions resuspension did not occur at locations where the water cover depth was greater or equal to 1.0 m. Currents were likely responsible for the transport of resuspended tailings from shallower areas to locations where the water cover was deeper than 1.0 m.

Jan 1, 2000

By D. E. Munson, T. M. Torres, D. A. Blankenship

The Thermal/Structural Interactions (TSI) In Situ Tests are a series of large scale, well instrumented tests that have been constructed at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. As a precursor to the TSI tests, a ventilation drift (Room D) was mined, drilled and instrumented. This room provided the contractor an excellent area to practice controlled construction methods and was a proving ground for construction monitoring and documentation methods. All gages in this first room have been monitored since their initial installation, which has provided a small, but representative, data base. These data also were the first to be available from any TSI area for analysis. This paper discusses the construction activities in Room D and the data generated from the construction and drilling. Deformation of the room is compared briefly to numerical calculations that used a rather simple creep model as a reference. The constitutive model for salt, it appears, must be improved before it can predict the underground deformations.

Jan 1, 1986

By Hidehiko Nakazaki, Sakuro Murayama, Mitsuo Miura, Masaaki Endo, Yoshiaki Hurukawa

This is a detailed report of construction experience of a tunnel built by a shield of rectangular cross section with reinforced concrete segments. In case of tunneling by a rectangular shield, there were the following problems to be overcom by technical developments; (1) structural joints between segments, (2) complexity in erector handling, (3) exact steering operation of shield and perfect filling of tail void left around the lining erected. Such rectangular shape of cross section has various advantages comparing the conventional circular shape as follows; (1) effective utilization of excavated space, (2) greater overburden depth, (3) stability of lining against unbalanced earth pressure caused by neighbouring construction.

Jan 1, 1979

By M. A. Ackerson, R. E. Griffin, W. H. Pomroy

Two automated fire detection system configurations have been used successfully in underground mines: the pneumatic "tube bundle" approach and the electronic telemetry approach. The electronic telemetry approach is more widely used, owing to its greater speed, flexibility, and capacity to both monitor other underground conditions, and remotely control underground equipment. However, depending on specific mine conditions and layouts, pneumatic detection, or a combined pneumatic/telemetered system may offer significant advantages over the telemetered approach alone. This paper describes research by the U.S. Bureau of Mines to design and in- mine test a rapid response pneumatic fire detection system tailored to the unique requirements of multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. A Bureau developed proto- type system is described with emphasis on design features which counter commonly perceived and/or experienced pneumatic detection system operating problems. Finally, the results of a 3-yr in-mine performance evaluation of the prototype hardware are discussed. Included are descriptions of system layout and coverage, response time, tube leakage, sample dilution, elimination of accumulated water from sample lines, and system maintenance and reliability.

Jan 1, 1989

By P. R. Sheorey, D. Barat, B. Singh

Presented is a stability analysis for a trial stope in a lead-zinc mine. The trial scope would have an excavation width of 20 m with an initial height of 3 m. Filling would commence when the scope was heightened to 6 m. A two-pronged approach to predict the stability of such an opening was used viz. the finite element method and the rock mass classification method. Corroboration is shown to exist between the two methods. Deep borehole extensometer observations during stope extraction have been compared with predicted displacements.

Jan 1, 1981

By Charles E. Scott

The molybdenum industry has been in a depression since the beginning of the decade. Real molybdenum prices are significantly reduced from 1979-1980 levels when there was a perceived capacity shortage and continued expectations of burgeoning demand. Primary capacity brought on stream since then has been unable to operate profitably and indeed, in light of high inventories and reduced demand, has been largely unnecessary. Structural changes in the molybdenum industry will be needed in the future to weed out superfluous capacity and to expand demand through new product applications.

Jan 1, 1986

By J. L. Gent

Compressed air distribution networks are essential for powering equipment in many mines even though some mines are replacing them with electrical power for hydraulic drills. Compressed air can be costly especially if the system is poorly designed and maintained. This paper outlines a technique for proper compressed air system design that will help mine managers reduce compressed air power costs; an important topic in today's highly competitive international minerals market. Compressed air system design is complex. It requires specifying: 1) air quantity and pressure in all branches of a large network, 2) proper location and types of valves and fittings, 3) the network solution that determines compressor requirements, 4) optimal hose and pipe, diameters, 5) receiver and compressor accessories, and 6) required capital and operating costs.

Jan 1, 1989

By Jonathan M. Pachter

The Bailey mining complex is located in Greene County, PA in the valley of Talley Run, a small stream tributary to the Enlow Fork of Wheeling Creek as shown on the location map insert found on Figure 1. The Bailey complex includes two Pittsburgh No. 8 Seam deep mines (Bailey and Bailey #2), a coal preparation plant, and two refuse areas (for disposal of coarse and fine processing waste). Clean coal is shipped from the complex via a 24.15 km (15 mile) rail spur, which connects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Company (Consol) began a permitting effort aimed at beginning construction of Bailey, the largest underground coal mining complex to be built to date in the United States. Construction of the Bailey Mine began in December, 1981, less than six (6) months following the first application submittal. Clean coal was produced by the Bailey Preparation Plant in September, 1984. Effective project planning, including early formulation of a project planning team, identification of "red flag" issues, innovative responses to environmental questions and development of environmentally sound project designs, all contributed to the relatively quick permitting at Bailey.

Jan 1, 1985

By G. D. Criswell, F. Palkovits, J. M. Johnson

A paste technology investigation was completed for non-pozzolanic fly ash from Units 3 & 4 of PPL Montana’s Colstrip Steam Electric Station. The purpose was to assess the feasibility of converting from dilute slurry deposition of ash products to a system using thickened or paste ash to reduce excess water storage in the impoundment, reduce seepage losses, and increase storage efficiency. The investigation included laboratory and field testing to characterize the rheological, geotechnical and dewatering properties of the ash products, an assessment of potential seepage reductions and an evaluation of potential for increased ash storage capacity by modifying impoundment operating procedures. The studies concluded that the conversion project was feasible, cost effective, and permittable. Critical facilities for the conversion project are currently under construction.

Jan 1, 2004

By J. A. M. Cano

Introduction Since the beginning of operations at the pellet plant at Ponta Ubu ES, Samarco Mineração SA has produced pellets for direct reduction and blast furnace processes. Of the total amount of pellets produced from 1977 through 1993, 55 % are used in the blast furnace, about 45 Mt (49.6 million st). The principal components of pellet gangue are calcium oxide, magnesium oxide, silica and alumina. They should be added in adequate quantities to guarantee the mechanical resistance of the fired pellets under blast furnace conditions. Over the years, the pellets produced by Samarco had a silica content between 2.5% and 2.8% and varying binary basicity preferably between 0.8 and 0.85. On the other hand, the increasing amount of industrial waste in siderurgical plants caused by the increase of steel production has caused some countries to put into practice methods to reduce the volume of slag produced in the blast furnace. This paper's goal is to find an alternative for decreasing the amount of slag produced in the blast furnace. It is possible to decrease pellet gangue by decreasing the silica content to about 2%, leaving the metallurgical properties and quality of pellets unaltered. For this work, Samarco pellets were used with Si02 between 2.5% and 2.8%, pellets with high silica and pellets with Si02 between 2.0% and 2.3% low silica. Both were partially fluxed by the range of varying basicity CaO/SiO2 from 0.8 to 0.95 during production. Experimental tests on pilot scale Thhis work began in January 1986 in the pilot plant (pot grate, Fig. 1) at Samarco. Its goal was to obtain preliminary data that would indicate the bybility of the project. It also formed a solid base to extend the studies in tests on an industrial scale of production for blast-furnace pellets. The pot grate is a test furnace composed of a gas burner, a combustion chamber and a grate, connected by hot air ducts. The burner is fed by a mixture of LPG and air. It reaches high temperatures through oxygen injection. The combustion chamber heats the air that comes from the turbocompressor. This hot air flows through the ducts to the grate on which the pellet samples are fired. During updraft drying, downdraft drying, preheating, firing and afterfiring, the upward and downward direction of the air flow can be controlled by valves driven by pneumatic cylinders. The pot grate indurator was fully automated in August 1989. Positive and negative pressures measurements resulting from gas passing through the pellet layer, as well as temperature readings, are recorded in graphs in relation to time for all tests. The tests depend on the various steps carried out in sequence that can influence the results of the tests. Therefore, some criteria were adopted to restrict the number of variables in the process. This was done to facilitate the results of the analysis. The pellets were composed of concentrate, bentonite, hydrated calcitic lime and metallurgical coal, all regularly used in the pellet plant. The material balance of the pellets mix was determined from the chemical analysis of the components. Table 1 shows the chemical characteristics of the concentrate and the additives used in the pilot plant and industrial tests. The basicity has a marked influence on the metallurgical properties of the pellets produced by Samarco with a silica content between 2.5% and 2.8%. However, for pellets with low silica (about 2%), it was necessary to study the variation in the parameters of quality in a wide range of basicities to deliniate with precision a scope of work. A large variety of low-silica blast-furnace pellets were produced at the pilot plant with binary basicity varying between 0.8 and 0.95. After chemical analysis, those pellets were separated into five groups of different binary basicity (0.8, 0.84, 0.87, 0.90 and 0.95). Each was then split, one part for metallurgical tests in the laboratory at Samarco and another to be evaluated in a laboratory for metallurgical tests in Germany. It was agreed that the tests to evaluate the quality of the pellets in the two [ ]

Jan 1, 1996

By L. R. Chirinos

The Tintaya mine of BHP Copper, located in Southern Peru, includes a copper oxide deposit hosted in a mineralized skarn zone. The ore contains large amounts of clays and high acid consuming species resulting in low heap leaching performance. A treatment scheme was proposed that included a wet screening separation. The coarse fraction would be treated by heap and the fines by agitation leaching. The dissolved copper would then be recovered through solvent extraction and electrowinning (SXEW). Testwork determined the optimum heap leaching conditions to treat the oxide in on/off pads of 3 meter height with an initial acid cure followed by variable acid strength during irrigation. The method resulted in a reduced acid consumption and good copper recoveries.

Jan 1, 1997

By H. E. M. N. Moursy, Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, D. Chandler, G. Walker, Regis Stana, Patrick Zhang

The reaction kinetics of the acidulation of Moroccan phosphate rock (32% P?05) using 45% nitric acid were investigated using the Shrinking Core Model (SCM) , a newly developed Diffusion Model (DM) and a newly developed Combined Reaction and Diffusion Model (CRDM). This was achieved buy conducting a number of experiments in a controlled batch reactor system at different temperatures. The conversion and the reaction rate were calculated at different time intervals. The SCM based on reaction time and the CRDM characterize the acidulation process of phosphate rock. Diffusion of nitric acid and the products of acidulation at the early stages of reaction through the phosphate rock were found to be the rate-controlling step, resulting in a dif- fusion coefficient, which controls the mass transfer process. The reaction kinetics were found to fit first-order kinetics especially during early stages of reaction time. The deviation of the kinetics from first-order at later stages was due to the fact that the overall reaction was mass transfer controlled with respect to nitric acid and products diffusion.

Jan 1, 2002

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC) is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub located in northeastern Utah. This paper covers the successful driving of 1,525 m (5,000 ft) of dogleg downgrade decline with a 70-ton Paurat Roadheader mining machine and a conveyor muck-handling system. Ground support is with rock bolt and shotcrete; welded wire mesh is optional. The Upper Decline of 3.89 m by 8.69 m (12.75 ft by 28.5 ft) was mined through the Uinta Formation sandstones and shales in 210 days. The sandstones have a compressive strength in the 48 MPa (7,000 psi) range with a few bands of shale up to 137.8 MPa (20,000 psi). Green River Formation dolomitic marlstone with some sandstone lenses was mined in the Lower Decline 3.89 m by 5.64 m (12.75 ft by 18.5 ft) in 175 days. The Green River marlstones are tough massive formations ranging up to 206.8 MPa (30,000 psi). Roadheaders for use on steep slopes must be modified to accommodate the particular problems associated with mining downdip. The paper concentrates on the application of Roadheaders to steep slopes and the problems of mining tough materials such as marlstone. The paper also shows the advantage of using the method of excavation on long drives.

Jan 1, 1985

By R. V. Ramani, R. Bhaskar

Control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. Understanding the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been at-tempted. In this paper, first, a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It in¬corporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.

Jan 1, 1987

By Kambhampati C. Rao, Cecil Lue-Hing, Nabih P. Kelada, William B. Willborn

improvements in the analytical techniques for cyanide speciation can furnish useful information about the behavior of the different cyanide species in the receiving environment. This could be of help to the environmentally concerned public and the regulatory agencies in the assessment of cyanide limits for effluents, stream quality, and land disposal of cyanide bearing wastes. In addition the ability to distinguish the free cyanide and the weakly bound cyanide from the strong ULTRAVIOLET IRRADIATION UNIT (LAMP, COIU3' HOUSING) FIGURE 1 complexes, as well as transformation to thiocyanate is also needed by different industries, such as mining and metal finishing, etc., to evaluate the efficiency of several processes. Cyanide has been used for the recovery of gold since the late 19th century. Although cyanide leach solutions are mostly recovered and used again, a large quantity of cyanide bearing wastewater becomes unfit for use and has to be treated before it can be released into natural waterways.

Jan 1, 1992

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By R. F. Hüttl

World-wide Germany is the leading lignite mining nation. Most of the lignite is produced in opencast operations. However, opencast mining causes enormous impacts on natural ecosystems and even on entire landscapes. The extensive production of lignite particularly in eastern Germany results in large devastated areas, which so far have been reclaimed only to some part. For the restoration of the post-mining area of more than 80,000 ha the major land use option is the reestablishment of forest ecosystems. However, adverse site conditions of the post-mining landscape such as extreme soil acidification and salt concentrations call for specific recultivation practices. Therefore, after the German reunification new reclamation and reforestation concepts have been developed for these brown coal areas of eastern Germany by the Collaborative Research Center (SFB 565) at the Brandenburg University of Technology at Cottbus (Germany). As a case study our comprehensive investigations into forest ecosystem development on terra nova in the Lusatian lignite mining district, south-east of Berlin, will be presented.

Jan 1, 2003