Search Documents

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By Huo Zuzhao

The main feature of caving methods is to draw ore from the overlying waste rock. Research on the movements of ore and waste plays a very important part in reducing ore loss and dilution and raising the economic benefits. This paper gives the basic theory of computer simulation of ore-draw, exposses the physical significance of mathematical model, puts forword a new formula of similarity characteristic value, brings forth a method of adjusting similarity, introduces the major functions of the simulation program and describes the ore draw control and stope parameter selection through computer simulation.

Jan 1, 1986

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR&apos;s) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR&apos;s are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR&apos;s and incapability of discovering multiple IRR&apos;s of even multiplicity. In this paper, a concept of the &apos;cash flow pattern tree used for isolation of the real IRR&apos;s of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR&apos;s of a project. The method examines whether or not real IRR&apos;s exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR&apos;s, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986

By Scott Brien, O&apos

Cyclones have become standard unit operations in mineral processing for both dewatering mineral slurries and for making separations at given particle sizes. Conventional cyclones are normally able to make moderately sharp cuts. However, the limited ability to control water flow out of the apex means that cyclones have difficulty handling fluctuations in feed. Underflow-regulated cyclones are cyclones with a rubber boot attached to the underflow. This boot acts as a non-return valve and restricts flow out of the apex of a cyclone. Normally, this type of restriction on a cyclone causes severe difficulties in cyclone operation. However, by adding a siphon arm to the overflow, water flow can be controlled. The siphon arm creates a vacuum that reduces or eliminates the air core, permitting better control of the ratio of water flow out of the overflow and underflow. A Linatex-developed underflow-regulated cyclone was compared to a conventional cyclone for its ability to dewater a sand slurry. The underflow-regulated cyclone produced slurries with solids contents as high as 80% in the underflow. Conventional cyclones produced lower solids content in the underflow under similar conditions.

Jan 1, 1997

By H. Bernatowicz

The Nucoalyzer (On-Line Nuclear Analyzer) is a new method recently made comercially available for monitoring the elemental composition of a process stream. Applications for the Nucoalyzer include grading ore on a conveyor belt before or after it has gone through primary crushing, monitoring the slurry being transported in a pipe to the concentrator, and monitoring the stream of concentrate or the tailings from the concentrator. The Nucoalyzer may also be used at the smelter to monitor elements in the feed that include copper, sulfur, iron and silicon where a uniform feed is desired. The advantage of the Nucoalyzer over most other techniques are (a) it performs the measurement directly on the process with no sampling necessary, (b) the analysis can be performed on streams of particulate and slurries, and (c) the system does not have to make contact with the material it measures. These Nucoalyzers are operating at coal fired power plants and several more are about to be placed in service. This paper discusses the principles of operation of the Nucoalyzer, our experience in the field, application of minicomputers to data reduction, and potential applications in the ferrous and non-ferrous industries.

Jan 1, 1982

By M. Cambridge

The extractive industries are currently, and will continue to be, major contributors to the world economy, particularly in the developing world where economic growth is dependent upon a sound supply of primary materials. However, tailings dam and other mine failures have been very much a feature of recent anti-mining publicity, particularly in Europe, and thus instrumental in inhibiting new mine developments. Although, superficially, the record of dangerous incidents might support the anti-mining position, closer inspection suggests otherwise. This paper reviews the failures which have occurred over the last 50 years and demonstrates that, though poor practice is an ongoing problem for the industry, the record is one of improvement in both design and practice. Examples are provided of significant events which have led to dramatic advances in design and operation. The paper assesses the improvements made in technology and practice, and concludes that historic events must continue to form the underlying basis for design and operation of future mining projects.

Jan 1, 2005

By Patrick A. Ley

Maintaining, managing and manipulating large quantities of geologic data can be a very costly and time-consuming process. The use of computer-based methods can provide some relief to the problems of editing, displaying, and interpreting spatial geological data. ENCORE is a system designed specifically for coal orebody modeling and reserve esitmation where the geologic data is stored on a large mainframe computer and is accessed from a local work station for editing, manipulating, and producing various reports and high-quality engineering maps. The ENCORE system was designed for use by the geologist or mining engineer with little or no computer background and, additionally, it was designed to provide the geologist or mining engineer enough flexibility to be able to select the appropriate methodology for the orebody being analyzed. The various analysis tools incorporated into ENCORE can significantly increase the professional&apos;s productivity without burdening he or she with the need to understand the details of the internal computer language.

Jan 1, 1982

By Gordon F. Revey

In underground construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speedup the work and lessen costs. The process of determining whether or not blasting is practical is often complex, particularly when risks are high. In this paper, general methods of conducting blasting risk evaluations and outlined and considerations for blast design and risk management are reviewed. This paper also includes three blasting case histories demonstrating how these techniques were used at recent projects. In the first case, a cautious blasting program was developed to facilitate the removal of concrete and rock within a large section of an active mineshaft. The second case involved critical blasting to excavate a dry lake-tap connection between a tunnel and a shaft at the Southern Nevada Water Intake No. 2 project in Henderson, Nevada. The third case history describes how novel blasting methods were used to carefully drop a 2,721,500-kg (6,000,000-lb) concrete caisson into a1.2-m (4-ft) rock socket at the Detroit Outfall No. 2 project in Detroit, MI.

Jan 1, 2001

By C. G. Bock

Geologic profiles constructed from exploratory drill holes gave basic geologic information for bidding on 4913 ft. of twin rock tunnels under the Potomac River. To provide additional geologic information for construction, tunnel faces and shafts were mapped throughout excavation. This information was plotted in plan and section so that geologic structure could be projected ahead and prediction of conditions could be made. In structurally complex areas, 3-D models were made and used to show the geologic structure. Core from exploratory drill holes was relogged and structure oriented with that found in the tunnels to make the ultimate use of the core and refine the geologic picture. As excavation proceeded, geologic mapping showed that the projection-prediction approach was useful and essentially correct.

Jan 1, 1974

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By Mark J. Zdunczyk

Short Mountain Silica mines the Clinch Formation, an orthoquartzite, for silica sand. The operation is located near Mooresburg, TN, about 80 km (50 miles) northeast of Knoxville. Short Mountain is a local geographic name given to an area of resistant sandstone (Fig. 1). The area is part of the Clinch Mountain system that extends from eastern Tennessee to southwestern Virginia. The thick sandstone unit is more technically called a quartz arenite (orthoquartzite) that forms most of the mountain. In 1980, a Knoxville resident brought the Clinch Formation - Short Mountain in particular - to the attention of the large silica-sand producers as a potential silica-sand mine. Working with a local contractor who owned several hundred acres on Short Mountain, the Knoxville resident contacted interested companies. Many silica companies reviewed the property including Ottawa Silica Co., Pennsylvania Glass Sand Co. (both now US Silica Co.),Unimin Corp.,The Morie Co. and others. AFG Industries was the main market for the glass sand product from this potential mine. It had two plants, both within trucking distance from the site. All the silica sand producing companies, however, declined to develop the site. A few years later, Unimin Corp. decided to drill and evaluate the deposit. From that evaluation, Unimin leased the property but later dropped it. The relatively limited market for the Short Mountain product as well as Unimin’s recent acquisition of Carolina Silica were reportedly instrumental in the company’s decision to let go of the lease. Several other companies-unrelated to the silica sand industry - looked at the site but no one was interested in developing it. In 1986, J.D. Nicewonder, owner of coal mines in Virginia and Kentucky, was approached to investigate the site. Nicewonder began to develop the site with the intent to produce glass sand to supply AFG Industries. In May 1988, the first shipment of sand was trucked to AFG Industries.

Jan 1, 1992

By S. W. Beckman, L. Williams, A. E. Seep, R. Fischer, J. Hubbard

Introduction The Summitville Mine located in southwestern Colorado was added to the National Priorities List in June of 1994. Summitville was the site of mining operations that began in 1873 with the discovery and development of gold placer and lode deposits in the late 1800&apos;s. The mine site is located about 25 miles south of Del Norte, Colorado in the San Juan Mountains adjacent to the Rio Grande National Forest at an approximate altitude of 11,600 feet. The site was mined for gold, silver and copper between 1873 and 1947. The Summitville Consolidated Mining Corporation, Inc. (SCMCI), a wholly-owned subsidiary of Galactic Resources, Ltd of Vancouver, Canada ran a large tonnage open-pit mine and cyanide heap leach operation from 1986 to 1992 (Pendleton and Posey, 1992) During the mine operation by SCMCI, approximately 10 million tons of gold ore was mined, crushed and stacked on a lined leach pad. Heap leach operations experienced water balance and unplanned solution discharges from the start of the mine life. Despite the production of 249,000 troy ounces of gold during the mine operation, SCMCI was unable to meet remedial requirements and notified the state of Colorado of its intention to file a Chapter VII bankruptcy in December 1992. The EPA Region VIII Emergency Response Branch took over site operations on December 16, 1992 to prevent a catastrophic release of hazardous substances to the environment. The multiple contamination sources at the mine site are due to both historic and SCMCI mining operations. Emergency response operations at the site have prevented releases of severely contaminated solution and a permanent treatment for all waste units at the site is under investigation. A Request for Proposal (RFP) was issued in October 1993 by Environmental Chemical Corporation (ECC) at the Request of EPA Region VIII, Department of the Interior and Bureau of Reclamation. The RFP requested that interested companies provide information on their ability to implement innovative treatment technologies to improve treatment efficiency and reduce treatment costs for remediation of the heap leach pad (HLP) spent ore and ore leachate solutions. Dames & Moore and Pintail Systems, Inc. (PSI) jointly submitted a proposal suggesting application of biotreatment processes for detoxification of cyanide in spent ore and HLP leachate solutions. The proposal was accepted for pilot and field demonstration under the SPA Superfund Innovative Technology Demonstration Program (SITE) with additional funding from EPA Region VIII. This report discusses the test program and results of a Focused Feasibility Study which demonstrated biotreatment processes for spent ore cyanide detoxification.

Jan 1, 1995

By Zhang Zhitie

The limitations in mechanism research of mineral comminution in the past and the basic features of the comminution process have been analyzed. Two kinds of catastrophe model, i.e., cusp model and swallowtail one in the mineral comminution have been put forward. The dissipative structure of the mineral comminution: entropy production rate, extra entropy, extra entropy production and system stability has been discussed. The physical nature of the behavior that an old structure was destroyed and a new one was produced in the mineral comminution process has been brought to light.

Jan 1, 1995

By L. Shevenell

Nevada now has, or will have, 35 pit lakes resulting from open-pit mining below the water table. State regulators are requiring that the ultimate pit lake water quality be predicted as part of the permit application process. Water balances/pit lake filling rates must be esti¬mated in support of the geochemical modeling. In Nevada, analytical and numerical methods have been employed for the study of pit lakes. In the current work, analytical solutions are investigated for one pit lake, the Getchell south pit lake, which previously filled be¬tween 1968 and 1982 during a hiatus in mining. Water levels vs. time are available for this lake and these data have been fitted with a hyperbolic curve. This water-level-vs.-time curve was used in simple water-balance computations to find the net inflow rates by forcing computed water levels and volumes to match those of the known water levels and volumes through time. The model described here provides realistic volume fluxes into and out of the lake on a monthly basis as the pit lake filled.

Jan 1, 2000

By Frank F. Aplan, Edward C. Dowling, Richard R. Klimpel

Several series of time-instantaneous samples were taken on a cell-by-cell basis in the flotation circuits of the Pinto Valley, AZ copper concentrator. These samples were used to calculate mass flow rates throughout the circuit using standard, deterministic metallurgical formulae and also a variety of more statistically oriented techniques. Because of the magnitude of the errors associated with the individual cell samples, the standard metallurgical formulae are not sufficient. Consequently, it is necessary to utilize some type of statistical technique capable of distributing the individual cell sample errors in such a way so as to provide a physically useful mass balance for the entire circuit. This paper explores the use of linear and least squares programming as one technique to providing credible mass balance calculations. For linear programming this was done by distributing the error using two different criteria involving specific linear programming formulations: least absolute sum minimization (which assumes an underlying double exponential distribution error structure) and minimax (which minimizes the maximum absolute deviation and assumes an underlying rectangular distribution error structure). These results were then compared to the more standard formulation of minimization of the sum of least squares which assumes an underlying normal distribution error structure. The least absolute sum approach was particularly attractive due to its simplicity of use and the ease in which repetitive calculations can be done with no user intervention.

Jan 1, 1990

By Jon Y. Kaneshiro, Donald W. Scapuzzi

The primary purpose of the Prototype Installation Facility (PIF) for the Superconducting Super Collider (SSC) in this conceptual design was to test the magnets and other physics equipment. PIF was located in the northwest quadrant of the SSC 54 mile (87 km) main ring and consists of the first segment of tunnels, approximately 17,060 lineal feet (5.2 km) of 12 foot inner-diameter (ID) (3.7 m) tunnel, three 250 ± foot (60 m) deep shafts, connecting tunnels, and associated niches and alcoves. PIF would be the first portion of the main ring collider tunnel to be constructed. The geology, underground excavation conditions, underground facilities, and contractual considerations are discussed.

Jan 1, 1991

By R. Sharma

The heterogeneous distributions of nodule sizes, cover-ages and abundances and the variability of their burial und association with sediments and rock outcrops on the seafloor have emerged as crucial parameters in considering the exploitation potential of the manganese nodules in the central part of the Indian Ocean. Nodules with the long axis measuring from 20 and 40 mm (0.8 and 1.6 in.) account for nearly 60% to 70% of those evaluated from photographic and grab-sample data. In addition, 75% of the nodules (by weight) are between 20 and 60 mm (0.8 to 2.4 in.). The distribution of nodules with abundances ranging from 1 to 20 kg/m2 as well as coverages of 1 % to 90% on the seafloor are important considerations in demarcating the potential areas for nodule mining. The mining of areas with higher concentrations of nodules, such as along slopes associated with less sediment, would result in the enhanced recovery of nodules compared to areas with low nodule concentrations, such as in valleys and plains where thick sediment covers occur. The mining head will encounter substrates such as hard rock exposures, either with or without Fe-Mn encrustations, as well as soft sediment layers in the nodule fields. It must be able to collect buried nodules under sediment cover, and it must be able to negotiate uphill and downhill slopes in mining areas. Mapping prior to mining must delineate areas to he avoided and must define locations to be mined. The requirements suggest that the nodule collector must be a dynamic (active) system with sensors to detect areas of potential nodule concentrations, as well as features that are hazardous (or unfavorable) for mining operations.

Jan 1, 1999

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By William Highton

If the economic situation in the Western World evolves on a path similar to that of the past decade, then we Mining Engineers must accept that one of the major cost factors in the production of deep mined coal is going to be that of labour. Whilst not trying to over-simplify matters it does appear that one of the ways of maintaining acceptable coal costs is by obtaining more coal without increasing manpower. One such way could be an increase in the use of the retreat method of mining. The paper theorises and illustrates case studies to show that as the Mining Industry extends the use of Longwall retreat mining systems in coal seams where the risk of spontaneous combustion exists, then the use of bleeder entries should be questioned. In addition to the spontaneous combustion risk, bleeder entry systems where the ventilation flow is not fully controllable cannot be construed as a safe and reliable method of controlling high rates of methane emission. These two major aspects alone should be sufficient ground for Mining Engineers to re-consider the practice of using bleeder entries. An alternative "The Back Return System" appears to offer most of the advantages for controlling the environment, without the disadvantages of the other system.

Jan 1, 1980

By Antoon W. van der Vooren, Colin R. Phillips

A comparison of analytical models used to describe deposition in the first generation of lung bifurcations is presented. In order to allow testing of the mathematical models, experimental data were obtained from radon daughter deposition in simplified lung bifurcations. The experimental data for particles deposited by diffusional mechanisms is best described by the assumption of a thin concentration boundary layer at the entrance of a right circular tube. Other more complex models do not accurately describe the deposition of submicron particles. The angle of bifurcation was found to have a minor effect on deposition.

Jan 1, 1981