Search Documents

By M. Hardy, K. Nielsen, M. Ramey

American Soda, LLP has commissioned the first solution mine for recovery of naturally formed sodium bicarbonate (nahcolite) from low-grade deposits using high-pressure, high-temperature injection fluid. This project, known as the Yankee Gulch Project, was commissioned33 years after discovery of the deposit and followed an intensive four-year feasibility study that included a full-scale pilot test. The nahcoliteis co-mingled with oil shale and is impermeable. Solution mining is achieved by a combination of thermo-mechanical cracking and dissolution. Elevated temperatures are required to initiate the thermally induced cracking and to enhance solubility of the nahcolite, which is highly temperature dependent. This paper will provide an overview of the development of the project from discovery, characterization, pilot testing, permitting and commissioning, with emphasis on the solution mining aspects.

Jan 1, 2003

By B. Farshadi, B. Asi, M. J. Habibian

"In this paper, the most significant environmental aspects that are identified in the Taft Copper Project (TCP) are the quality and quantity of water, pollution of the existing watercourses and post-mining land use, matters such as air and noise pollution are deemed to be of less significance. Analysis has been performed for Do Nothing Alternative, Pre-stripping Phase, Mining Phase, Closure and After-use Phases. Analysis of the environmental assessment of TCP was carried out in three stages. In the first stage, the general negative and positive aspects of the project were identified. In the second stage the intensity, magnitude and significance of the environmental impacts of the project were identified. The third stage is related to the final conclusions of the assessment team and the relevant reasoning. A modified Leopold Matrix was adopted for evaluating the significance and magnitude of the environmental impacts. For this project, the matrix was modified to allow the assessor to take account of negative and positive numbers."

Jan 1, 2011

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By Eberhard Werner

Existing reports on the effects of mine subsidence on water wells and springs appear to be inconsistent. Some report quick and complete recoveries to pre-mining conditions while others indicate long-term or permanent effects. It is clear that topographic and geological factors as well as precise position with regard to the mine are important in determining probable effects of subsidence on aquifers. Ridgetop aquifers which are well above regional base-level are much more susceptible to disturbance by mining activities than those located topographically lower. Effects seen are attributed largely to increased permeability, both horizontal and vertical. of the aquifer rocks. The deeper aquifers usually show short term losses or water-table declines. but the effects on the ridge-top aquifers persist for longer periods or may be permanent. Subsidence enhances permeability. so that infiltrating water moves much faster to lower levels. causing pond and stream losses and declining levels in wells as well as declining flows of springs of the higher aquifers, while increasing levels and flows of the lower aquifers. Additional effects are shifts of spring locations caused by minor tilts due to differential subsidence and redirection of shallow flows by changes of horizontal fracture permeability. These effects are seen as mining of a panel progresses beneath the site. and are often repeated when adjacent panel mining fronts pass the site. Analysis of water well level and spring flow records indicates that the effects are greatest at the edges of longwall panels in the tensional regime. These effects are amplified for locations close to topographically steep terrain and in close proximity to fracture traces mapped from medium-to small-scale aerial images.

Jan 1, 1986

By M. J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to In Situ Leach Mining (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Casa Grande mine, transmissivity fluctuations are spatially correlated. This suggests that, at the scale of ISLM, the hydraulic process is heterogeneous, and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the Simulated Annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming and that uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be re-evaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1994

By S. W. Swerson

25.1-THE PURCHASING FUNCTION The word "purchase" means "to obtain by paying money or its equivalent; to buy for a price." This definition is all too simple to properly describe the word "purchase." One should consider the basic objectives of purchasing-to procure the right material, of the right quality, in the right quantity, at the right time, from the right source at the right price. Here it should be noted that in purchasing it is recognized that the best quality or grade of materials may be the only grade to purchase for a specific job. However. there are other jobs where the medium, standard or poor grade of materials is the right quality, as the lesser grade will perform adequately. In some companies the purchasing department makes the decision as to the right quality, while in others this function is shared with other departments. Years ago in business the owners controlled the purchase of required materials and services by performing the task themselves. The owners obtained the type materials and services they needed and paid the price demanded. This function was performed along with all the other duties requisite to the owner of a business, namely, clerical, hiring and firing of personnel, financial management, etc. As companies grew in size, clerical duties were assigned to other personnel and the owner usually retained the purchasing authority. This same division exists today in many small companies. However, in the larger companies, the purchasing function has been assigned to a separate department. Importance of the Purchasing Function-The larger the company the greater the need for a separate department to perform the purchasing function. Today the purchasing agent for most larger progressive companies has policy-making authority. Therefore, it is reasonable for him to report to the president or vice president of his company. Studies of several hundred companies show the purchasing department head reporting to top management 87.5% of the time. This fact in itself is indicative of the importance of recognizing that effective purchasing requires a department staffed with specialists in the field of procurement with knowledge and experience sufficient to perform in today's complicated business atmosphere. In the manufacturing field it is a common axiom that usually half of the company's dollar expenditures are for materials. If a purchasing department functions properly and the right product or service is purchased and a savings accomplished, the contribution to the net profit of the company is much greater, as opposed to sale dollars, where only a small portion is carried forward to net profit. Thus, the importance of the purchasing department and the contribution it can make to the success of the company are obvious. 25.1.1-THE PURCHASING FUNCTION 1. Responsibilities of the Purchasing Function-The purchasing agent in performing his function is acting as an agent for the company and others in the company requiring materials and services. Accordingly, he is committing the company for materials and services subject to certain limitations which the board of directors may stipulate. In view of this, the purchasing agent,'^ position must of necessity he

Jan 1, 1973

By V. K. Kollipara

Dust dispersion characteristics in mine airways are important for developing engineering controls for dust and explosions. Authors here have used CFD modeling approach to analyze the dust dispersion characteristics in mine airways. The technique was initially validated with the published field experimental data. The results obtained were in a reasonable agreement. CFD validation results show that in a single entry the dust concentration decreases exponentially as a function of distance. Finer particles can travel up to a distance of 350-400 m away from the source. Parametric studies indicate that air velocity and input dust concentration has significant influence on dust concentration distribution. CFD modeling was then applied to study the dust dispersion characteristics in a room-and-pillar mine layout. Preliminary results show that dust concentration distribution is highly dependent on the airflow patterns and air velocity distribution. The distribution is not exponential until the velocity in the travel way becomes uniform. Data developed in this study may be used to design mine layouts and engineering controls for dust control and explosions.

Jan 1, 2011

By S. A. Moffatt, S. K. Kawatra, T. C. Eisele

This paper describes the decomposition of bulk samples to fine particles using alkali metal vapors. Basalt, pyrite, alumina, pyrex and quartz glass samples were exposed to sodium vapors at elevated temperatures for different time periods up to 30 hours. Examination of the particles showed that fragmentation occurred preferentially along grain boundaries. Emphasis of this paper is on the theory of the degradation mechanism and the size distribution of the particles produced.

Jan 1, 1992

By Peter Zhang, Daniel Su, Bo Hyun Kim

Shale gas wells drilled in longwall chain pillars are influenced by longwall mining. Longwall mining on each side of the chain pillars can create overburden movements and induce deformations in gas well casings. If the deformations result in a casing breach, intrusive shale gas could leak into the longwall mine with serious safety consequences. This study concerns five shale gas wells in the chain pillars between two adjacent longwall panels in the Pittsburgh coal seam under a cover depth of 670 ft and a mining height of 7 ft. The gas wells were constructed with typical casing design, but a casing cementing alternative with uncemented production casings was practiced. Four production casings were uncemented, and one production casing was unintentionally cemented with good quality cement to a 535-ft depth and low-quality cement stringers from a 444- to 535-ft depth. The longwall faces passed by the shale gas wells as each adjacent longwall panel retreated. Production casings were surveyed by a multi-finger caliper after each panel was mined. No deformation was detected in the four uncemented production casings, but small deformations were detected in the partially cemented production casing. The maximum measured deformation in the cemented production casing was 0.05 in. after first panel mining and 0.06 in. after second panel mining. The casing deformations were also predicted by the FLAC3D model set up on site-specific overburden geology. The predicted deformations were in good agreement with the measurements in terms of deformation locations and magnitudes. All five shale gas wells resumed normal production after being temporarily plugged during the period of mine-by. This study provides a successful demonstration of the effectiveness of a casing cementing alternative for decoupling production and intermediate casing, and thus minimizing the influence of longwall mining in the shale gas wells drilled through longwall chain pillars.

Jul 1, 2023

By Armine F. Banfield

Selection of a plant site is becoming increasingly more difficult and important, mainly due to advances in technology, antipollution laws and changing economic, social and community conditions. Discussion falls naturally under three headings: economic considerations, terrain considerations and environmental considerations. Aside from acquisition of surface rights, problems having to do with terrain, or topography, usually can be dealt with by management alone. Economic considerations largely involve decision-making by management plus negotiations with government regulatory agencies acting under set rules. Environmental considerations, such as air and water pollution, townsites, housing, schools, noise abatement, appearance, surface rehabilitation and the like usually are under the control of federal, state or municipal bodies with a large degree of decision-making. Successful solution of environmental problems often requires lengthy negotiations, during which public relations by the mining company play an important part. Existing union regulations or customs may confine decision- making and the establishment of wage rates, working conditions and regulations. These usually require considerable planning and negotiation. Initial production often is delayed by formal negotiations involving environmental considerations. Surface facilities usually can be divided into two broad categories: those for concentrating ores--such as gold, silver, base metals, low-grade iron ore and potash-which should be close to the mine to reduce ore-transportation costs to a minimum, and those where the ore is shipped elsewhere for treatment, such as direct-shipping iron ores, complex high-value ores requiring specialized treatment and ores from which special products are derived for local markets. The long-term aspects of plant-site selection too often are given no or insufficient consideration because of immediate financial limitations. As a result, additional capital expenditures may be required later for relocation of townsites, roads, railroads and plants to provide additional room for extension of open-pit operations, tailings disposal, storage, or danger to foundations through underground subsidence or open-pit mining. In the past, hillside sites for concentrating plants were preferred to take advantage of gravity-feed methods The modern trend, however, is to place as much equipment as possible on approximately the same level. Some costs relating to plant sites are included in this section. They are ranges as of the year 1970, and are offered only as general guides. Such costs will vary widely with geographical location and, of course, are subject to escalation due to increases in wage rates and cost of materials. Items in the bibliography contain more detailed and comprehensive data on specific subjects. Most contain bibliographies of their own.

Jan 1, 1973

By V. Paul Keran

Design of the Bajo de la Alumbrera project started in June 1995. Concentrate production began early in the third quarter of 1997. The project is situated in northwestern Argentina. Alumbrera is being developed by Minera Alumbrera, which is owned by MIM Holdings of Australia (50%), North Limited of Australia (25%) and Rio Algom of Canada (25%). Alumbrera is Argentina's first modern copper mine. This article outlines the key process- and plant-layout features that were incorporated in the Alumbrera concentrator design. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity-gold circuits in both the primary and the regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998

By W. E. Foreman, A. Hayatdavoudi, A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three cationic-anionic polymeric conditions. For each polymeric condition, two mathematical models were developed, one for overflow response and the other for underflow response. The combination polymers produced the best quality of overflow and underflow. For this polymeric condition, change in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of underflow quality. The mathematical models generated a set of plots that would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1991

By J. R. Cooper

Since man began beneficiating ores, a limited number of factors influenced the type of treatment. The ore itself has always been a factor. The first form of concentration was probably hand sorting, and the grade of concentrate and recovery had to be considered from the start. The cost of labor as a factor in mill design did not attain importance until the period following World War I. Power was one of the cheapest commodities available, and consequently power consumption was ignored. That no longer holds true. The present work does nothing to simplify the work of the metallurgist, or designer. On the contrary it adds another element to the design considerations. And while this report concentrates on power consumption, the mill designer must take the other factors into account as well. This study is based on a compilation of data supplied by a number of Western United States copper operations, as well as information from equipment manufacturers. Although its conclusiones apply to other minerals and geographic areas, the information is more precise, when applied to similar ores. The discussion has been divided into sections covering crushing, grinding, and flotation as these are the principal power consuming functions.

Jan 1, 1977

By Frank L. Peterson

This paper deals with problems of groundwater development in an insular circum-Pacific environment, and is not oriented as such to mining and mineral development. Nonetheless, because a reliable water supply is necessary for most mining and related support activities, and since water supplies are limited in many insular parts of the Pacific Basin, groundwater development is a subject which must be frequently addressed. Because many in the audience may be already familiar with groundwater development for continental environments, I have chosen to deal with groundwater occurrence and development problems which for the most part are unique to insular environments. In such environments, the local geology plays a critical role in determining groundwater occurrence and its suitability for development. The three examples discussed in this paper-Hawaii, Guam, and the Marshall Islands-were selected because they illustrate groundwater occurrence in a wide range of geologic conditions. For example, the Hawaiian aquifers consist primarily of basaltic lavas, while Guam is made up of andesitic lavas and coral reef limestones, and the Marshall Islands are coral atoll deposits. Despite differences in aquifer size and rock types, the principal mode of groundwater occurrence at the three sites is similar; thus, development strategies are also similar. Figure 1 shows the location of the three sites.

Jan 1, 1982

By André G. Journel

As opposed to graphics applications in medical sciences and mechanical engineering, computer imaging of the subsurface faces a severe problem of data shortage. Most graphics softwares include an interpolation algorithm aimed at producing slick graphic output, irrespective of the attribute being interpolated, the quantity and quality of the data available, and what the map is intended for. It is suggested that the power of modern computers be also used in providing representations of the subsurface that accurately reflect actual spatial variability and the large variety of soft information available beyond hard data. Since any subsurface representation is uncertain, a measure of that uncertainty should be provided which can be used for risk analysis.

Jan 1, 1992

By Dorothy A. Canter

Three Federal programs exist for identifying significant environmental chemicals, including minerals, that should be tested for toxicological effects. Two programs are mandated by law and can lead to industry-funded studies; they are administered by the Environmental Protection Agency and the Agency for Toxic Substances and Disease Registry, respectively. The third is the National Toxicology Program, a Federally-funded testing initiative. This paper summarizes the three programs, describes their similarities and differences, and discusses their applicability to minerals.

Jan 1, 1991

By C. B. Cecil

The sulfur content of United States coal can be assessed by using a variety of approaches. The sulfur content may be expressed in terms of total sulfur in the coal, pounds of sulfur per million Btu, or sulfur remaining after reduction by coal preparation. In addition, the sulfur content may be applied to the demonstrated reserve base or to coal resource estimates. Unfortunately current data bases do not allow for an integrated assessment at the National level. Although classification of coal resources and reserves according to sulfur content is arbitrary, preferential production of low-sulfur reserves will positively skew the total sulfur of the remaining coal resource.

Jan 1, 1986

By Scott G. Britton

Until now, only the range of typical construction projects which are repeated over and over during the life of a coal mine have been discussed. This chapter looks at underground construction projects which occur only once or twice during the life of any given mine and are major construction projects in both time and cost. These projects usually require the services of an outside engineering and construction firm with hands- on experience in design installation. Because of this involvement with engineering and construction firms (EIC), the role of the construction engineer will change from one of actively de- signing and directing tasks to one of planning, inspection, and quality control. To reflect this role change in the discussions, the focus of this chapter will be changed to a broad overview of project participation. Of course, the projects under consideration in this chapter could easily fill more than one book on their design and installation. In addition, major construction projects are extremely site specific, requiring months of data collection about site geology, physical conditions, and potential excavation and construction requirements. Therefore, no attempt shall be made to discuss any detailed construction aspects as was done in earlier chapters. The purpose of this chapter is to present the fundamental concerns of a staff engineer or supervisor. This engineer does not make the decisions on choosing the EIC firm, but assists and interacts with their project team to accomplish the goals set forth by higher management. The construction topics to be reviewed fall into three main categories. The first category is highlighted by the installation of a main surge bin; the second is typified by the construction of an underground shop; and the third category encompasses special projects such as rotary dumps, crusher stations, and foremen's offices. These categories highlight the differences between degrees of mine responsibilities for project completion. The first topic is usually a turnkey project by an E/C firm for a given mine. The second topic represents the leading role of the mine in the project with a contractor as a support service or equipment supplier only. The third topic, special projects, is an example of a joint venture-between a contractor (leading partner) and mine management. These roles can change with any given project, but the changes in management responsibilities for the construction engineer can be nicely illustrated for the purposes of this text. The first step toward constructing major mine projects is to analyze the mine which influence their design. From the mine management standpoint, these parameters should reflect the role the mine will play in the project construction. In other words, what is the nature of the proposed mine environment and what are the material, labor, and time requirements needed to assist or direct the chosen engineering and construction firm? Answering these questions requires some basic project planning and cost estimation work. Here, only a general treatment is necessary, since detailed discussions of these topics will follow in Chapters 8 and 10. For those persons interested in the role of the EIC contractor, I suggest beginning by reviewing the article by Beall, "The Role of an Engineering and Construction Contractor," presented in the October 1980 issue of Mining Engineering magazine.

Jan 1, 1983

By Peter J. Lawson, John A. Rideout, Gregory W. Dicinoski

A considerable body of literature directed towards optimising the efficiency of gold and silver extraction from cyanide leach liquors has appeared in recent years. A few examples from dissolution to solvent extraction to adsorption in carbon-in-pulp (CIP) and resin-in-pulp (RIP) operations follow. Selective leaching of gold from copper-gold ores using ammonia-cyanide mixtures extends the % copper which may be tolerated in ores (Ruane, 1991, LaBrooy et al., 1991, Costello, 1991). The removal of copper and recycling of cyanide from high copper ores is another important development (Sceresini and Staunton, 1991). Solvent extraction of alkaline cyanide liquors (Riveros, 1990, Mooiman & Miller, 1991) and solvent aided elution in CIP (Muir, et al., 1985) look promising. Recent definitive papers on the mechanism of adsorption of aurocyanide by activated carbon should lead to more efficient use of CIP (Adams and Fleming, 1989, Klauber, 1991). Strong and mixed weak-strong base resins have been applied in RIP for aurocyanide extraction in Russian Plants since the 1970's (see for example Borovskii et al., 1985, and references cited in Fleming, 1988a). Fundamental studies on applications of commercial weak and strong base resins-in-pulp (Fleming & Cromberge, 1984a, b, Fleming 1988a, Hosking 1984, Riveros and Cooper 1987) have generated much interest in RIP. Detailed comparisons of CIP vs RIP efficiencies at Mintek in South Africa (Fleming et al., 1988b), and the inefficiency of CIP in contact with clay led to the commissioning of the strong base RIP Golden Jubilee plant in 1988. Its operation and improvements have been reported (Seymore and Fleming, 1989, Fleming & Seymore, 1990). The use of anion exchange membranes for aurocyanide extraction shows some promise (Mauthoor et al., 1991). However, the development of new gold specific resins at Mintek (Green et al., 1984, 1986, 1990, Johns and Green, 1991) and elsewhere (Asker et al., 1987, Wilson et al., 1987, Harris et al., 1992) should improve the viability of RIP processes. The polydiallylamine gold specific resins (Hodgkin & Eibl, 1988, Fawell et al., 1992a, b) have high capacities for auro cyanide recovery from high concentration liquors. The use of guanidine based liquid and solid ion exchange extractants for gold was recently reported by the Henkel Corporation (Kordosky., et. al., 1993). Such specific resins tailor made for gold and/or silver cyanide extraction should lower overall cost by improving metallurgical efficiency. In the case of strong base resins this selectivity largely eliminates the problems of poor base metal elution and/or poisoning. The work reported here outlines the approach taken at the University of Central Queensland to synthesize sterically hindered strong base anion exchange resins which are designed to have high selectivity for auro- and argentocyanide complexes. It summarises selectivity tests on low grade cyanide leach liquors from several mines. It also examines an RIP vs CIP comparison, and investigates the elution properties and cycling of one such promising resin.

Jan 1, 1993

By Donald C. Moore

Asamera Minerals Cannan Mine has been producing a 170 g gold/tonne (5 oz gold/ton) siliciaus flotation concentrate since July 1985. Flotation concentrate is shipped to a smelter for gold recovery. Numerous processes have been investigated to economically produce bullion on site. This paper describes the laboratory and pilot plant test results of a bacterial assisted oxidation of the refractory minerals. Economic comparisons with autoclaving and roasting processes are included.

Jan 1, 1989