Search Documents

By D. Ince

Flotation of dolomite from apatite was investigated, using dodecylamine hydrochloride or sodium oleate as the collector, with and without inorganic modifiers such as sodium chloride. Separation of dolomite from apatite was anticipated from the single mineral experiments under various pH and collector concentration conditions. Flotation selectivity in the mixtures, however, was found to be limited. Attempts to control the flotation response of these minerals by addition of salts such as NaCl and KCI indicated that selectivity is possible. The presence of sodium chloride was determined to depress apatite flotation using sodium oleate, leaving dolomite flotation unaffected (Moudgil and Ince, 1989). In this paper, conditions for optimum separation and the effect of major parameters on the desired selectivity are discussed.

Jan 1, 1992

By Adam Feiler, John Ralston

Optical reflectometry was used to study the attachment and subsequent detachment of silica particles (diameter 25 nm) from the surface of titanium dioxide wafers under well-defined hydro- dynamic conditions. Atomic force microscopy was used to measure the interaction between silica spheres (diameter 7 pm) and titanium dioxide wafers under the same solution conditions. In addition to repulsive electrical double layer forces, adsorbed polyphosphates provide a short-ranged steric layer that reduces the lateral interaction between the surfaces. The use of these two complementary techniques has given valuable insight into the process responsible for fine particle detachment and has particular application to surface cleaning.

Jan 1, 2003

By H. Sevim

This paper summarizes the research effort in simulating the operation of "Underground Coarse-Coal Hydrotransport Systems" (UCCHS). The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distributions of operating parameters such as water and power consumption and amount of slurry delivered to the preparation plant. Knowledge of the distributions of these parameters is essential for the efficient operation of the system.

Jan 1, 1987

By Gemei Yang, Yihui Zhao

In caved goaf, the friction loss of fluid head is: [h = (R'+ R/Q/ )] Q (for one-dimensional transition flow). The R' and R, which are the functions of two dimensional spaces, are calculated through an empirical formula. Then, the bulking factor and permeability are determined. It is supposed that the airflow in porous media are similar to those in tiny tubes crossing each other. Therefore, the network calculation technique can be used to tackle the field transition flow problem. A lot of case studies showed that the emission of methane in mines mainly depends on the air velocity and has little relation to air pressure. Summing up our experience and experiments, we provide an empirical formula to calculate the gas emission rate per unit area. By means of mass conservation and network calculation, the methane content distribution in steady-state is worked out. Then the dynamic change in airflows and gas content can be analyzed by the characteristic-difference method.

Jan 1, 1987

By Gary A. Almeraris, Thomas F. Peyton

This paper chronicles the mining of a main interceptor sewer through a residential neighborhood for the MWRA's Boston Harbor clean-up. The Wellesley Extension Sewer Tunnel consisted of 490 m (1600 ft) of rock tunnel, 107 m (35V ft) of mixed face and 336 m (1100 ft) of softground. The tunnel was located 4.6 m (15 ft) below water table and passed directly beneath six buildings with as little as 7 m (23 ft) of cover. In addition, the tunnel ran parallel to and within 4.6 m (15 ft) of an existing sewer tunnel with flows up to 187,5 million liters (50 million gal.) per day. The rock encountered by the tunnel was comprised of gramodiorite, amphibilite and diabase. The soils which passed through the tunnel face consisted of tills, sands and non-cohesive plastic silts. The techniques developed and the equipment utilized to successfully mine this complicated ground are described.

Jan 1, 1991

The objective of the fines flotation step in a coal preparation plant is to maximize coal recovery subject to a constraint on the allowable ash in the concentrate. The objective is achieved when the incremental ash is driven to a target value determined by an economic constraint. In this paper, a phenomenological flotation model and ash analyzer combination are identified that allow the development of a soft sensor for incremental ash and subsequently a model-based strategy which manipulates key flotation variables to achieve the control objective. A combination of plant tests and computer simulations are presented to evaluate control-system performance in one operation.

Jan 1, 1999

By L. Laage, R. Greur, W. Pomroy

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry, for routine ventilation calculations and mine emergency planning. This paper describes recent work by the US Bureau of Mines and Michigan Technological University to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program, and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1995

By Matthew J. Hrebar

Dragline stripping operations account for over one-half of the U.S. bituminous coal production mined by surface coal mining methods. The dragline is a popular stripping tool because of its flexibility in varying overburden depths and relatively low operating costs per cubic yard of overburden. Because of the relatively high capital costs of the machines and their use as a primary stripping tool, the selection process is an important step in the mine planning procedure.

Jan 1, 1979

By Firoze E. Katrak, John R. H. Black, Paul R. Ammann, Michael J. Loreth, Servi. Italo S.

Germanium is produced primarily as a by product from zinc concentrates. The important sources of gallium are alumina ores (bauxites) and zinc concentrates and residues from zinc processing. In addition, gallium as well as germanium may soon be recovered from a depleted copper mine near St. George, Utah. The major uses for germanium are in semiconductors, lenses in infrared optical systems, catalysts, and gamma radiation detectors. The major markets for gallium are in light-emitting diodes, solar cells, laser diodes, integrated circuits, microwave devices, and magnetic bubble memories. CRA projects a healthy growth in the demand for both metals. However, the role of scrap metal will continue to be important over the next decade, thus decreasing the overall demand for primary gallium and primary germanium. This paper summarizes the key elements and the economics of the markets for germanium and gallium. Much of the information, such as plant-by-plant costs of production and estimates of consumption by end use for various countries is from proprietary databases of Charles River Associates.

Jan 1, 1986

By Kim Lapakko

As part of a project funded by the US EPA, through the Western Governors' Association, the recent literature on the prediction of acid drainage from metal mine wastes was reviewed. Static tests such as Acid Base Accounting, Modified Acid Base Accounting, B. C. Research Initial Test, and APP:S Test attempt to quantify the total capacities for a mine waste to produce and consume acid. In kinetic tests (e.g. humidity cells, soxhlet extraction, elevated temperature oxidation, column tests, batch reactor tests, B. C. Research Confirmation Test) mine waste samples are subjected to oxidation and the resultant drainage pH is assumed to reflect that of mine wastes dissolving in the field. This paper summarizes information presented in the recent literature on static tests.

Jan 1, 1992

By C. J. Konya

When blasts are designed, the assumption is made that all blastholes release near ideal energy. In many types of mining operations, some blastholes release very little useful energy. These blastholes will be called malfunctioning blastholes. Recent studies indicate that on many types of blasting applications, 30 percent of blastholes are malfunctioning. This malfunctioning routinely occurs on the operation and is not an unusual occurrence. This paper will discuss the cause of malfunctioning blastholes and methods to minimize the detrimental effect on both safety and costs.

Jan 1, 1988

By J. W. Jang, I. Iwasaki

Introduction Grinding ball wear in wet grinding is due to a complex combination of abrasion, corrosion, impact and their interactions. The ball charge is continually falling from a height greater than half of the ball mill's diameter, and contact is made with ore particles or other balls. Abrasive wear occurs through penetration and plowing of media materials from the ball surface by hard ore particles (Gangopadhyay and Moore, 1985). Electrochemical interactions between the abraded and unabraded areas of the ball surfaces, as well as between the grinding media and the minerals, occur in grinding mill pulps (Adam et al., 1986). The wear depends on the media composition, the hardness and the corrosive/abrasive characteristics of the slurry. The marked-ball-wear test method was used to evaluate the performance of grinding media under nitrogen and oxygen atmospheres. Also, the wear mode was studied by observing the grinding media surface under a scanning electron microscope. In general, grinding media of high hardness and high chromium contents were found to have better corrosive wear resistance than those of low hardness and low chromium contents (Jang, Iwasaki and Moore, 1988). The purpose of this investigation was to determine the size distribution and the shape of wear debris in a study of the wear rates and wear behaviors of grinding balls. Experimental Materials The grinding ball alloys used in this investigation were: •martensitic stainless steel (MSS; 0.96% C and 16.2% Cr), •high-carbon, low-alloy steel (HCLA; 0.89% C and 0.53% Cr), and •mild steel (MS; 0.22% C and 0.09% Cr). The mineral used in this study was synthetic corundum, because it was on hand and contained no magnetic impurities. Debris A 203- mm (8-in.) diam porcelain mill was used for grinding the corundum. The mill charge consisted of: •1200 g of 12-grit synthetic corundum, •770 mL of 0.05 mole/L Na2SO4 (61% solids), and •125 steel balls of nominally 25-mm (1-in.) diam. To minimize the debris corrosion, nitrogen was introduced into the mill. Grinding with MSS, HCLA-steel or MS balls was conducted for 2 hr at 51 rpm. The grinding time using the MS ball was varied from 0.5 hr to 2 hr in an attempt to study the debris amount and shape as a function of time. The debris was collected with a hand magnet from the ground slurry and separated from the corundum particles using a Davis magnetic tube. After the separation, the debris particles were immediately washed with acetone and then filtered and dried. Debris size analysis Buckbee-Mears 3-in.-diam, micro-mesh sieves and an electromagnetic shaker were used for determining the debris size distribution. In sieving, isopropyl alcohol was used. The debris fraction collected from each sieve was washed with acetone, dried and then weighed on an analytical balance. [ ]

Jan 1, 1993

By Djamhur Sule, Husaini

Almost 90 % of phosphate in Indonesia is consumed for natural and manufactured fertilizers, while the rest is used in chemical industries. The consumption of phosphate always increases each year, while Indonesian phosphate production is almost constant at around 75,000 tons annually, except the production in 1988 was 165,000 tons. Due to the limited amount of domestic production, the imported phosphate is increasing each year. Phosphate trading in Indonesia is unique. Some of the domestic production is exported to Taiwan, while phosphate from USA, Morocco, Jordan and Nauru is imported. Indonesian phosphate includes guano phosphate, caving phosphate and small amount of marine phosphate sediment. Problems with Indonesian phosphate include: scattered deposits in difficult locations and a relatively small amount of reserves. Exploitation of phosphate deposits for domestic purpose has a good prospect, mainly because of the rapidly increasing phosphate demand as natural fertilizer or as a raw material for manufacturing fertilizer to support an agricultural sector.

Jan 1, 1993

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on overall grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: •Different lining profiles in rubber and steel. •Orebed magnetic lining. •Steel-cap rubber lining. Introduction Grinding mill liner life has been a subject of extensive studies. Performance of mill liners in terms of wear life and how it relates to lining material and profile is abundant in the literature. The most economical liner material and design has been selected based on "cents per ton milled". The evaluation of the effect of liner design on power and grinding media consumption which is a far more significant part of grinding costs, has been less comprehensive (Fig. 1). Lining materials Steel. The most commonly used lining material is steel, calculated on a volume basis. Steel linings have a long tradition and a number of alloys is being developed. The main families are: •High chromium white iron. •Cr and Ni white iron (NiHard). •High chromium martensitic steel. •High carbon Cr-Mo perlitic steel. •High carbon Cr-Mor martensitic steel. •Manganese austenitic steel. Steel linings can be successfully used in most applications. Rubber. Rubber linings were introduced 25-30 years ago and are today commonly accepted to be the most economical linings for secondary and regrind applications. Rubber linings offer long service life in these applications and generally [ ] outlast steel in wet applications, where corrosion is a factor on the steel. The cost relation between rubber and steel has changed dramatically over the years. In the past rubber was more expensive than steel, but today, the cost of rubber is close to half the cost of steel, calculated on a volume basis (Fig. 2). The present cost situation has made rubber linings an economical alternative in several primary grinding applications as well. The wear rate of rubber in primary applications is higher than the wear rate of steel, thus giving a shorter wear life. This can be compensated for by making the rubber lining thicker. The cost advantage of the rubber allows for this, but care must be taken not to jeopardize the grinding performance. Rubber, as a lining material, offers some distinct advantages over steel lining, such as: •Ease of installation and removal. •Safer to handle, less risk of injuries. •Faster replacement. •Reduces noise.

Jan 1, 1996

By T. F. Deems

The nature, usage and comparatively rare occurrence of ball clay is described. The importance of these white firing plastic clays in ceramics, particularly in the production of industrial sanitary ware and tiles, is emphasized. The US deposits are briefly discussed. What is known about relevant deposits in Brazil, Argentina, Colombia and Venezuela (the four largest ceramic producers in South America) is also described. The ceramic plants have been sited near the centers of population rather than the plastic clay deposits. At present, extraction is probably concentrated on surface residual deposits and lenses which require minimum investment. Native plastic clays are used exclusively in the tile plants, but in sanitary ware, they are often used as extenders of imported ball clays.

Jan 1, 1997

By S. Behl, S. Mathur

The viability of physico-chemical purification methods such as selective, flocculation for the separation of two components having similar chemical compositions and the same crystal structure but different surface properties is demonstrated. A loss of selectivity was observed in a dolomite-dolomite mixture when polyethylene oxide (PEO) (five million molecular weight) was used us the flocculant. Heteroflocculation was minimized using a low molecular weight PEO (MW =105) as a site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at the 100% recovery level

Jan 1, 1996

By Dennis A. Giardino, Leonard C. Marraccini

This paper surveys noise levels, noise exposure patterns, and frequency spectra found in the mining environment; the effects of mining noise on the working population; and the quantification of hearing loss in the coal mining industry. Federal mining noise regulations and the present state of the industry, with respect to noise control technology, are discussed. Examples of proven noise controls for mining are included along with measured noise reductions.

Jan 1, 1986

By E. F. Divers, R. A. Jankowski

In response to a request from the Mine Safety and Health Administration (MSHA), the US Bureau of Mines completed a respirable dust survey of 18 US coal preparation plants. Of these, three were essentially free of dust problems. Respirable dust exposure to workers in the remaining plants depended on the time spent in the dusty areas. In five of the plants surveyed, Bureau tests showed that in some areas worker exposures could exceed Federal dust limits in less than two hours. Cooperative studies were arranged with coal preparation plants using three different dust control techniques. These included a standard baghouse-type dust collector, two types of scrubbers, and an electrostatic precipitator. Results of these evaluations are presented. Various types of ventilation systems used during summer and winter conditions were also evaluated. Results showed that appropriate ventilation can provide a highly cost-effective method for controlling coal preparation plant dust.

Jan 1, 1987

By R. Parkins

This paper will discuss a method used to refine the fill level, and orifice size for a dual motor conveyor drive with extended delay chamber fluid couplings. The subject conveyor is located on the surface at the Mountain Coal Company West Elk Mine, located near Somerset, co.

Jan 1, 1996

By Jaroslaw Drelich

This report briefly reviews the measurements and interpretation of adhesion forces measured between microscopic probes and substrates having micro- and nanoscaled roughness characteristics that were recently conducted at Michigan Tech using atomic force microscopy. The laboratory study concentrated on both rigid and deformable materials, with the probes larger than the size of roughness features of interacting surfaces. For such systems, a detailed surface characterization in terms of roughness parameters, asperity size and shape, and spacing between asperities, as well as analysis of deformation of materials is required. Analysis of the experimental data can be done with theoretical models, which are suitable for rough surfaces and therefore allows to normalize the measured forces. Alternatively, loading of the probe during adhesion force measurements can be managed properly to control deformations of the nano-scaled surface irregularities. Controlling the deformation reduces and even eliminates the effects of nano-roughness on the probesubstrate contact area, promoting conditions described by the contact mechanics models for the sphere-smooth substrate system.

Jan 1, 2005