Search Documents

By Donald Crowell

Due to falling metal prices and depletion of ore reserves, lead-zinc mining in the Leadville, Colorado, area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Company and ASARCO with ASARCO being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Company of Salt Lake City in conjunction with the Central Engineering Department of ASARCO. The plant was constructed by Stearns-Roger Corporation. Construction began in the spring of 1970 and the plant went onstream in April, 1971. Flow sheets and equipment lists are attached. This paper will describe the flow sheet very briefly and discuss in more detail those aspects of the design which may be of interest, particularly the provisions for expanding the capacity of the plant.

Jan 1, 1972

By Jenny Alsén, Hans Hogard

"Construction of large facilities underground in urban areas has many advantages. In order to show the advantages, a case study of the Norsborg metro depot in Stockholm Sweden has been made. The Norsborg metro depot will be the largest and most modern underground metro depot in northern Europe. The depot has been built in hard rock in an urban area with small impact on the environment and local residents. The paper describes how it is possible to build underground facilities in a cost efficient way and take care of the challenges regarding working environment that comes with locating a permanent working place underground. INTRODUCTION The Stockholm area is one of the five fastest growing regions in Europe and home to more than a fifth of Sweden's population on just two percent of Sweden's surface. The population is growing rapidly, with about 35,000 people per year and is expected to reach 2.6 million in 2030. In order to meet the development and enable continued growth, housing projects and expansion of infrastructure need to keep the same pace; this is an easy conclusion to make but much more difficult to realize in practice. The main challenge is to accomplish development in a sustainable and efficient manner, minimizing the use of resources and land. By constructing facilities underground more urban space will be made available for development and/or for greening of city centers. Considering sustainability factors such as land value in decision making for placing of structures or facilities, underground locations could become a first choice alternative. During 2015 and 2016, several major underground infrastructure projects in the city of Stockholm will start, including a 14 km sewage tunnel and an 18 km by-pass highway tunnel. Furthermore the Stockholm metro system is currently undergoing the largest expansion since the 1970’s, a 19 kilometers extension of the metro system including new trains and new stations is planned. During 2013 - 2015 Skanska Sweden took part in the construction of a new metro depot placed underground in the southern part of Stockholm; the Norsborg metro depot. This is a top modern urban underground facility that in 2017 will serve as depot for 17 new metro trains. The project was selected for “Outstanding Project of The Year” at the ITA Tunneling Awards 2015."

Jan 1, 2016

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

The $2 billion Horizon Lateral includes over 30 miles of trenched and tunneled pipeline with diameters up to 120 inches.Related infrastructure includes large and small pumping stations, reservoirs, and flow control facilities. This paper will discuss the strategy and processes used to determine contract packaging and contracting delivery methods for the various project elements with an emphasis on the tunnels and trenchless crossings. Prior Authority experience and the rigorous risk-based approach to develop the preferred alignments played a large role in determining the outcomes along with schedule concerns and permitting and easement acquisition.

Jun 13, 2023

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By Ted DePooter, Mun Wei Leong, Chad Frederick

Downtown Bellevue Tunnel (DBT) is part of Sound Transit’s $3.7 billion, 14-mile light rail transit system from downtown Seattle, across Lake Washington, to the cities of Mercer Island, Bellevue, and Redmond. The tunnel was the first Sound Transit East Link project and posed significant construction risk. This paper discusses implementation of design changes to the soft ground tunneling method, implementation of several technologies such as the use macro-synthetic fiber initial shotcrete lining, use of spray-applied waterproofing, and use of shotcrete for the final tunnel lining. These efforts allowed for significant time and cost savings to the project.

Jun 13, 2021

Grouting is mainly used to improve mechanical properties or decrease the permeability of rock mass around civil and mining projects. The purpose of this paper is to present the most effective factors on grout penetration depth in rock mass. Such factors are essential for reliable estimation of the grout penetration depth and the expense for cement take of any grouting project. In this paper, about 50 different types of the relations presented so far by various researchers to estimate the depth of penetration in fractured rock were studied. The effective factors are classified to rock mass properties, grout properties, and operational factors. Results show that firstly, the discontinuities aperture and Lugeon value are respectively the most investigated factors of rock mass properties influencing on penetration depth. Secondly, the yielding stress, viscosity, and density of grout are the most effective factors of grout properties. Finally, grouting pressure has an intense effect among other operational factors. The investigations were also verified in Siah Bishe dam case study. Keyword: grout penetration depth, rock mass properties, grout properties, operational factors.

Feb 27, 2013

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.' Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By Syd S. Peng

University research in the U.S. consists of three components; faculty, funding, and graduate students or postdoctorals. Individual faculty is the unit area of research that is not limited, although faculty normally performs research in their areas of expertise. Faculty can and often do join with other faculty in multidisciplinary research. Faculty research achievements or reputation reflects the standing of the program and university. Therefore, research is highly encouraged and regarded within the university community. Graduate students are the work force of faculty research and doctoral students are preferred for high-quality products. The federal government provides the majority of funding sources, with the remainder coming from industry, state government and others. Compared with other engineering majors, the mining engineering programs in the U.S. are unique in that they: ? Are small in terms of the number of programs, and number of faculty and students in each program. ? Serve a single industry (i.e., mining) and are thus cyclic, reflecting the up and down economic state of the mineral industries. Enrollment statistics during the past 70 years show that a cycle consists of approximately 30 years with the first 10 years up, followed by 20 years down. ? Have curriculum designed to emphasize and thus serve for either the coal, hardrock or industrial minerals industries. These unique features make mining engineering programs hard to manage in university environments. Funding for mining research has relied primarily on the federal government, i.e., the former U.S. Bureau of Mines (USBM) and currently the National Institute for Occupational Safety and Health (NIOSH). The mining industry does not directly perform, nor sponsor research projects. Federal funding provides primarily in-house research. In the last four decades, federal extramural funding was only available when Congress appropriated extra funding in response to mine disasters. For instance, a string of coal mine explosions in the mid to late 1960s prompted Congress to enact the Coal Mine Health and Safety Act of 1969. It provided massive research funding from 1970 to 1983 covering all mining-related subject areas. From 1984 to 1995, federal extramural research funding was minimal, through two generic mineral technology research centers for selected mining engineering programs. In 1995, Congress closed the USBM and transferred the health and safety of miners program to NIOSH. Federally-funded extra-mural research practically stopped from 1995 to 2006. In 2006 and 2007, in response to a series of disasters, including those at Sago, Aracoma, Darby and Crandall Canyon, Congress again appropriated funding for short-term re-search in selected subjected areas such as underground tracking and communication, mine seal and ventilation, and deep cover pillar extraction. Therefore, to develop a meaningful academic mining research program during the past three decades, funding needed to be drawn from other sources such as the mining industries. A ?meaningful? program requires a sufficient amount of consistent funding in order to produce effective results. A review of federally funded extramural research pro-grams shows that a great majority of contractors/grantees are private entities, involving few mining engineering faculty. This, in part, is due to the fact that mining engineering involves so many different subjects. Therefore, a small mining engineering program can only have resources to cover teaching in the core subject areas (i.e., extraction, ground control, ventilation and material handling), at best. In this respect, a successful and meaningful academic mining re-search effort requires strong supporting programs such as geology/geophysics, structural (applied) mechanics, material sciences, compute/software application, etc. Therefore, academic mining research had to rely on private sources such as coal companies, in the author?s case, for sustained funding in the past three decades. Relying on funding from coal companies presents several problems. The projects were small and considered routine consulting projects requiring practical answers in a very short time frame. This is not really suitable for academic research, for which the major goal of research is the training of graduate students. These short-term projects vary with time and mines, most of which are driven by U.S. Mine Safety and Health Administration (MSHA) or U.S. Office of Surface Mining (OSM) regulations. So sustained funding under such condition requires broad experience of coal mining operations, which is also not well-aligned for academic research where faculty tends to specialize in a narrow field. Consequently, under such a funding environment, it is important to keep in mind how to develop long-term academic research objectives from conducting small short-term consulting projects that require quick solutions. In other words, how to look beyond the quick answers and to develop broader and more fundamental theories applicable to other situations that advance the-state-of-the-art. In order to achieve this objective, faculty must act as the connecting link because graduate students come and go. Faculty must know the detail of each project such that they know what are the important unsolved problems, what to assign to specific graduate students and how to guide the next group of graduate students to continue the development and advance the mining science. Under such funding environments, the most effective way to conduct academic mining research and ensure quality products is to maintain a research group consisting of postdoctoral, PhD, and MS students of various rankings such that the senior ranks can assist in guiding the junior ranks, especially the senior PhD students who are experts in their dissertation research areas. A weekly meeting should be scheduled for the group in which problems encountered in the research are discussed or individuals take turns presenting the progress of their projects. During each meeting, the importance of open discussion on scientific issues must be emphasized. Thus, opinions are encouraged, debated, and rejected or accepted. Students are encouraged to listen to and analyze other points of view. In addition to training of this thought process, the meeting also helps identify the strengths and weakness of each individual. As the subject of research expands over time, the group?s and, thus, the faculty?s research experience broadens. With this approach, companies can get the quick answer they desire from expert research experience and the faculty can engage in meaningful applied and basic research that is most relevant to routine mine operations. The end result is that companies will have a high regard for academic mining research.

Jan 1, 2009

By Thomas J. DeMull

Development of the Batu Hijau copper project was completed in the fourth quarter of 1999 with the formal handover and start-up of ore processing facilities. The project began in August 1996 when the owner, PT Newmont Nusa Tenggara (PTNNT), awarded an engineering, procurement and construction (EPC)contract to Fluor Daniel (FD) for the development of the project. This included a copper concentrator, port, power plant, town site and infrastructure. PTNNT managed the development of the mine and the procurement of the mine equipment. In 1996, Batu Hijau was the largest mining project ever undertaken. Developing the Batu Hijau Mine was complex. It involved the work of thousands of people in all parts of the world to plan, engineer, procure, fabricate and manufacture equipment, supply and deliver materials and equipment, and build the plant.

Jan 1, 2002

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By F. L. Pirkle, D. L. Pirkle, E. C. Pirkle, W. A. Pirkle

Heavy minerals have been mined from the sands of the United States’ Atlantic Coastal Plain since the early part of the twentieth century. Production of ilmenite from beach sands near Mineral City (Ponte Vedra), Florida, began in 1916. The first reported large-scale recovery of zircon in Florida was reported from this deposit in 1922 and of rutile in 1925. These operations ceased in 1929. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site. In 1942 heavy-mineral operations were established on 202 hectares of land situated in Duval County, Florida. The location is about 16 kilometers east of the center of Jacksonville, Florida, in an area known as Arlington. This operation demonstrated that low-grade sand containing only 2 to 3 percent titanium minerals could be concentrated economically with the Humphreys spiral and that the oxides could be separated from the heavy silicates by electrostatic methods. Much of this area is now covered by a large mall and is a major retail- commercial center. Between 1958 and 1964 the Skinner tract, a deposit about 4 kilometers south of the above deposit, was mined. Today the area of this deposit is known as Deerwood, a gated country club community on the southside of Jacksonville. Further inland, E.I. du Pont de Nemours and Co. has been mining heavy minerals from a physiographic feature known as Trail Ridge since 1948, and a deposit near Green Cove Springs, Florida has been in production since 1972. Since the start of heavy-mineral mining in the southeastern United States, nine heavy-mineral ore bodies either have been or are being exploited in Florida and Georgia. Other deposits either have been lost to mining or are yet to be mined. These deposits have different origins. Some formed along shorelines at the heights of marine transgressions while others formed on regressional beach ridge plains during periods of temporary stillstands or slight transgressions. These different origins are reflected in the chemical and physical characteristics of the deposits. Ilmenite in older, more western deposits has a higher TiO2 content than ilmenite in younger, more eastern deposits. TiO2 content does not very with north-south direction. Garnet and epidote are absent or rare in the older Trail Ridge deposits, but progressively become common in the younger Duval Upland, Crestal Pamlico, and Holocene deposits. Grain size is coarsest for Trail Ridge sediments and finest for sediments in Duval Upland and Crestal Pamlico deposits. The average grain size for Holocene deposits is intermediate between Trail Ridge and Duval Upland deposits. The two models for the origin of the heavy-mineral deposits – deposits formed at the height of major marine transgression; and deposits formed during periods of temporary stillstands or slight transgressions that occur during a general marine regression; - are consistent with known sedimentological data and depositional trends.

Jan 1, 2005

By W. H. Pomroy

In its 2001 diesel particulate matter (DPM) rule for metal and nonmetal underground mines, MSHA established an interim concentration limit of 400 micrograms of total carbon (TC) per cubic meter of air (400TCµg/m3), and a final concentration limit of 160TCµg/m3, to be phased in over five years. Following a court challenge to the 2001 rule, MSHA, industry and organized labor reached a partial settlement of the litigation under which the agency agreed to issue a proposal to amend the 2001 rule by, among other things, changing the surrogate from TC to elemental carbon (EC), applying MSHA's traditional hierarchy of controls, and revising requirements for one-year special extensions for complying with the final DPM exposure limit. MSHA issued a final rule in 2005 converting the interim concentration limit from 400TCµg/m3 to 308 micrograms of EC per cubic meter of air (308ECµg/m3) based on a miner?s personal exposure. Pending further rulemaking, MSHA retained the final concentration limit of 160TCµg/m3. In May 2006, MSHA issued a final rule that clarified that the final limit of 160TCµg/m3 would be based on a miner?s personal exposure rather than as a concentration limit. The 2006 rule also phased in the final DPM limit in three steps over two years, beginning in May 2006 at 308ECµg/m3, followed eight months later in January 2007 with a limit of 350TCµg/m3, and finally reaching 160TCµg/m3 in May 2008. Also in the 2006 rule, MSHA committed to converting the 160TCµg/m3 limit to an EC limit in future rulemaking. This paper reviews the DPM exposure limits in the context of the MSHA rulemakings and discusses the DPM engineering controls that were utilized by mine operators to attain compliance with each progressively lower limit.

Jan 1, 2009

By Ö. Kaya

The removal of gangue minerals from three different graphite ores (Inebolu, Akdag?madeni and Çoraklidere) from Turkey by acid leaching was studied. Acid leaching experiments were applied to the flotation bulk concentrates, which were obtained in determined optimum conditions after preliminary flotation tests. The effects of acid type, acid concentration, leaching temperature and leaching time on the dissolution of gangue minerals were studied. The most suitable leaching conditions were determined to be 20% HCl + 4% HF for acid type and concentration, 85 ºC for leaching temperature and 4 hours for leaching time. After removing the gangue minerals at these optimum conditions, the total carbon contents of the samples from Inebolu, Akdag?madeni and Çoraklidere increased from 23.51% to 40.07%, from 37.93 to 60.47% and from 42.28 to 59.47%, respectively.

Jan 1, 2009

By L. Tercero Espinoza, F. Marscheider-Weidemann, C. Gandenberger

"A reliable supply of non-energy raw materials is a precondition for the functioning of the European economy. In line with its importance, the issue of raw materials supply has become more prominent in the past years, especially owing to turbulent raw material markets. However, these turbulences are not due to depletion of the geological resources but to a missmatch of (expected) supply and (expected) demand, with several interacting factors influencing the markets both from the supply as well as from the demand side. A recent evaluation, published in June 2010 within the framework of the EU Raw Materials Initiative, sought to bring together these two sides of raw material markets and asked the question "which raw materials are critical for the EU?" Herein we present the methodology used by the Ad-hoc Working Group on Defining Critical Raw Materials and the results obtained, complemented by results from the study "Raw Materials for Emerging Technologies"."

Jan 1, 2011

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By R. D. Peterson

As underground mine operations expand, the ventilation systems supporting them become complex. Complexity increases with periodic ventilation changes. New diagonal connections require a rebalance of resistance to maintain airflow in affected splits in the system. Incidents of mine fires and explosions have occurred in U.S. coal mines when diagonal connections resulting from ventilation changes have resulted in changing airflow directions. MSHA regulations prohibit the reversal of airflow and poor ventilation practice in general, but regulations cannot stipulate or recommend proactive preventative measures because every situation is different. This paper discusses the phenomenon of diagonal branches and recommends practical precautionary measures that can be taken to prevent airflow reversal in planned ventilation changes.

Jan 1, 2012

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By Verya Nasria, William Bent, William Hogan

"The South Hartford Conveyance and Storage Tunnel (SHCST) project is a significant component of the Hartford Metropolitan District’s (MDC) long-term control plan (LTCP), which is overseen by the Connecticut Department of Energy and Environmental Protection (CTDEEP). This project will address a portion of the MDC’s Clean Water Project (CWP), which will reduce combined sewer overflows (CSOs), eliminate sanitary sewer overflows (SSOs), and reduce nitrogen released into the Connecticut River. The purpose of the SHCST project is to eliminate West Hartford and Newington SSOs, eliminate Franklin area CSOs discharging to Wethersfield Cove and minimize CSO discharges to the South Branch Park River. The locations of each overflow are shown in Fig. 1. In 2010, the district prepared a preliminary design report (PDR) for the SHCST project, which included relief of the Folly Brook trunk sewer and proposed to keep the tunnel boring machine (TBM) retrieval shaft within the city limits of Hartford. Figure 1 shows the 2010 PDR recommended tunnel route. Subsequent to the PDR, the objectives of the SHCST have slightly shifted. In accordance with ongoing revisions to the LTCP, relief of the Folly Brook Trunk Sewer is no longer necessary. Additionally, the MDC has decided to perform less sewer separation in the Franklin Avenue drainage area. To replace the sewer separation, new relief points are proposed within the Franklin area and will be diverted to the SHCST. Figure 1 also shows the current recommended tunnel route (Alignment F). During 2012, the MDC conducted an evaluation of the potential of connecting the proposed North Tunnel (originally proposed as an independent tunnel with its own pump station) into the South Hartford Conveyance and Storage Tunnel. This evaluation concluded that the two proposed tunnels could reasonably be connected together and operated as a single tunnel system utilizing the tunnel pump station at the eastern terminus of the South Hartford Tunnel (Fig. 2). It also was concluded that this alternative was less costly than two independent tunnel systems."

Jan 1, 2014