Search Documents

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By D. M. Loring

Radon progeny have been a health and safety concern for miners since the mining of radioactive minerals began. Through the ?nuclear age?, it has become better understood and the regulations have become more robust. Ventilation and control practices have improved, thus reducing miners? exposures. This paper provides an overview of radon in mining, the progress of the regulations, and discusses some of the uranium miner studies that contributed to the knowledge of the pathology of radon.

Jan 1, 2009

By D. Brady

When deciding to deploy rescue teams underground the decision makers need to be able to determine that there won?t be an explosion whilst the rescue teams are underground. Previously general body concentrations in areas likely to be travelled were compared to explosive limits on a one off basis with no formal process looking at trends or other areas. A new approach is being adopted that takes into account the rate of change of gas concentrations with triggers set to enable a withdrawal of personnel prior to a possible explosion and influences such a barometric pressure changes. This paper explains the rationale behind the changes made and the advantages and implications of adopting such an approach.

Jan 1, 2012

By G. V. Krishnan, L. Adler

A rock classification for drilling and boring is presented covering most equipment types and providing an estimation of the key parameters for operation, such as thrust and speed, and of performance such as penetration rate and bit life. Drilling and boring are significant and integral aspects of both the mining and heavy construction industries. Together these constitute over 20% of the G.N.P. Drilling and boring represent the most arduous mechanical processes performed in industry. Their misapplication quickly leads to equipment destruction, hazards, and to major delays. The classification is unified in two ways: 1) for a particular rock class several parameters can be estimated, 2) the classification integrates most excavating activities (i.e. digging, ripping and even blasting), and is derived from ground control. The rock classification provides a job property, based on fundamental and index properties, which yields quick and rough estimates of vital information. However it does not obviate the need for a more thorough analysis, and maintaining field records. BACKGROUND In order to adequately describe a drilling operation the conditions, activity, and equipment must be characterized. Of these the major independent variables are the conditions. Conditions focus on the geologic mass and also consider whether the site is surface or underground. The primary component of the geologic mass is the rock type, detailed below in Rock Characteristics. The other components

Jan 1, 1983

By Dave Ragland

The SDSU tunnel and underground station are the first of these type facilities to be constructed by the Metropolitan Transit Development Board. Because there is no previous experience, and because tunneling activities are associated with some risk, he MTDB has undertaken a very proactive and wide reaching program to identify and control risks during construction. Finally, because the tunneling activity and underground station is on the San Diego State University, MTDB is working closely with their staff to identify construction impacts and mitigation’s, and thus ensure a quality project for both agencies.

Jan 1, 2001

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

By N. C. Trivedi

Natural calcium carbonate, commonly known as limestone is an abundant resource pretty much worldwide. Calcium carbonate occurs naturally as the main constituent of chalk, limestone, and marble. One of the unique characteristics of this abundant mineral is its versatility. Major markets for calcium carbonate are: paper, plastics, caulks and sealants, carpet backing, paint, and food additives. This broad spectrum of consuming industries has warranted producers of this industrial mineral to be innovative and quality focused simply to meet the ever increasing demands for performance. This need for improving performance of calcium carbonate has led to the development of new sources of calcium carbonate, natural as well as synthetic.

Jan 1, 2002

By Howard J. Handewith

Long used in mine development in England, Europe and Russia, roadheaders are growing in size, features, productivity and application. Beginning with the basics, this paper covers the economic and the technical aspects of the new roadheaders in both mine production and development. The author explains how to choose and integrate roadheaders into ongoing operations as another step in the inexorable march from labor to capital intensive mining. Innovations now on the drawing boards are covered that are the challenge of the future.

Jan 1, 1983

By Fred Heivilin

A symposium on the characterization and toxicology of mineral dusts was held Sept. 19 and20 in Washington, D.C. The symposium was held to update the minerals industry, the health community, government agencies and academia on the technical, health and regulatory aspects of minerals to be evaluated by the International Agency for Research on Cancer (IARC).In October 1996, the IARC met in Lyon, France, to discuss and prepare “Volume 68 of the IARC Mono-graphs on the Evaluation of Carcinogenic Risks to Humans on Silica, Silicates, Dusts and Organic Fibers.”

Jan 1, 1996

In the present study, we have investigated the conditions for the formation of bubble clusters and the effect of well-defined agitation on the stability of clusters. A specially designed cell was used in which bubble clusters could be formed at the surface of a porous block in a fluidized bed of relatively coarse hydrophobic silica particles. The clusters then rose through a flow field of known turbulent characteristics. The size of the clusters before and after passing through the turbulent zone were measured using a high speed camera. The influence of shear rate on the deformation of the bubble clusters was investigated. The results showed that the Kolmogarov microscale was much smaller than the maximum cluster size, suggesting that the breakage of the clusters was mainly due to interaction with clusters in the inertial convection sub-range.

Jan 1, 2009

By R. P. Sloan, A. S. Whitford

In November 1999, CCI's Empire Iron Mining Partnership and MinnovEX Technologies Inc. developed an expert system for advanced control of their Empire IV Grinding Section. Empire IV is comprised of three autogenous Primary Mills and six autogenous Pebble Mills, with a single Pebble Crusher and high pressure Roll Press. The challenges of controlling and optimizing three distinct grinding lines that are inter-woven by a pebble crushing circuit were met with innovative and unique solutions. This paper will detail the approach employed at Empire and will focus on the aspects that make this application unique.

Jan 1, 2001

By J. Wagner, P. Eger, G. Melchert

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1% of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021

By Y. Wang

Wet magnetic separation methods for recovering hematite and chromite fines and ultrafines are investigated in this paper. These methods include wet high intensity and high gradient magnetic separations, carrier or "piggy-back" magnetic method, magnetic field-induced aggregation and magnetic seeding. This investigation indicates that wet magnetic separation is more efficient for fines and ultrafines whereas other methods can be used to enhance the particle aggregation and/or the magnetic response. The magnetic behaviour of these minerals with respect to magnetizing field, particle size and temperature is also presented.

Jan 1, 1993

By V. I. Kefeli

Public-private partnership efforts are working to create green landscapes from abandoned industrial sites. Fabricated soils, potentially an essential element of such landscapes, are designed to substitute for topsoil on the areas free from ground cover and plant community. The aluminosilicate matrix and humus form the soil micelle - the primary unit of any soil complex. Humus formation is a process based on carbon-nitrogen interaction. Sources of carbon can be materials rich in easily composted products like cellulose and polyphenols (plant leaves) or aged lignin polymers (saw dust from different woody plants). The pathways of carbon-nitrogen complexes are discussed. Properties of the fabricated soil components were examined by bio-tests and plant models.

Jan 1, 2002

Recent accelerated exploration efforts in southwest China have progressively quantified the vast phosphate resources in the Yunnan Province. To date, according to Chinese geologists, potential reserves in the province may be on the order of 4 Gt, which would equal the entire US reserve base. Development of this vast reserve is underway at two sites located 60-70 km southwest of Kunming, the provincial capital of Yunnan. The first, the Kunyang open-pit phosphate mine, produces an estimated 1.5 Mt/a of 22-30% P20,5. The other project located north of Kunyang is the Haikou mine, which the Chinese consider a possible 2.0-Mt/a operation. Because average ore grades run 3% less than those of Kunyang, beneficiation will be necessary. While the latter project has been initiated on a small scale, it is basically still on the drawing board. Brown and Root and the US Bureau of Mines are assisting on the project. Both operations are under the direction a regional administration which reports to the Ministry of Chemical Industries in Beijing. Combined production from both mines could represent some 70% of China's future productive capacity. Ore reserves in the region are estimated at 400 Mt by local officials. Geology of the District The phosphates are considered Cambrian in age and rest on a Precambrian dolomite. The Indian Ocean, Chinese geologists say, may have been the original source. The line of deposition stretches on a trend from Vietnam in the southwest, through Yunnan, into Sichuan Province to the northeast. Because the area is considered very stable from a geologic viewpoint, large quantities of phosphate have been deposited and large outcrops are known to occur everywhere in the province, according to Chinese sources. The Kunyang and Haikou ore bodies are thought to be two wings of an anticline with the former the southern portion, and the latter the northern portion. Each ore body strikes on an east-west axis. While there are many localized phosphate operations throughout the province, the Kunyang mine is the premium producer. Kunyang's Mining Development The Kunyang open-pit mine was opened in 1966. During the early years, operations were considered somewhat disorganized. Systematic mine planning and normal operations were not initiated until just two years ago, according to mine management. In 1979, Kunyang finally reached its design capacity of 1.5 Mt/a. The ore body consists of two phosphate beds separated by a band of shale. The top layer of phosphate varies from 4 to 8 m, averaging 6 m. The middle shale layer is 2 in. The third layer, which is not as rich as the top, is approximately 4 m. To further complicate matters, the ore dips 15° to the south over a strike length that is currently undefined, but believed to be

Jan 3, 1980

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By Greg Wieland

Deep sewer tunnels are required to meet future growth demands of the City of Austin?s down-town redevelopment. The tunnel is 18,000 ft long and varies in finished diameter from 54 inches to 96 inches. The tunnel crosses under Austin?s Town Lake three times and there are four main work shaft sites. Geology, groundwater, foundations, downtown redevelopment, and an active, healthy community put significant constraints on the design. This paper discusses a major underground project for downtown Austin and discusses the risk considerations and the opportunities the design team took toward optimizing the project design for the construction phase.

Jan 1, 2008