Search Documents

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 meters (8 feet) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting and saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can effectively prevent solution flow through large portions of the stockpile, implying that great care must be taken to ensure that ripping is carried out to a full depth of at least 2.4 meters (8 feet) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2000

By N. S. Tanious

The need to provide better mine roof support and control in longwall tailgate entries prompted the Bureau of mines to search for a replacement product for wood cribs. Their search isolated steel-fiber-reinforced concrete (SFC) as the most effective replacement. Through successful laboratory and underground mine tests, handmade SFC cribs proved to be a viable and more effective roof support system. However, to ensure wider usage, U. S. Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Company in order to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated during this program to determine their compressive strength and post failure characteristics. After considerable testing and adjusting of various concrete mixtures, a final formulation for the SFC crib blocks was selected. That formulation permitted the construction of SFC cribs possessing a nominal crib strength of 3200 psi (22.1 x 106 Pa) and a nominal modulus of elasticity of 1.0 x 106 psi (6894.76 x 106 Pa). These SFC cribs can support from 3.5 to 14.5 times as much load as a wood crib, depending on the size of the wood crib being replaced. Both laboratory and limited mine tests, conducted by U. S. Steel Mining Co. have shown the SFC crib to be an economical and effective means of roof control.

Jan 1, 1984

By S. Brummelkamp, G. Van Weert

Separation of minerals by shape has received little attention, since minerals normally do not break into different shapes during crushing and grinding. However, comminution of consumer wastes generates opportunities for novel separations based on particle shape. For instance, ductile plastics are broken into longer curved shapes, whereas brittle plastics yield angular particles. Using spouting beds for particle separation in water requires controlling the spout's instability. The preferred geometry for such redesigned spouting beds is reported. Plastic cylinders, discs and spheres were separated as a function of rising water velocity and amount of particles in the system. By using 5 mm particles, differences in settling behavior could be video recorded.

Jan 1, 1999

By L. A. Bakhvalov

According to the practice of mining management in the system of industrial complexes, the Kazakhstan gold mines are part of the mine processing industrial concerns providing ore-mining and ore-dressing. The cycle technology of winning operations used at the mining of vein deposits in the mines of the industrial concern is mainly provided by the systems of scrapping, scipping and electric locomotion. At present the information and computer system, elaborated on the basis of the Maikain underground mine is intended for creation of the system of automatic operation for the industrial complex mines. The information and computer system includes: - parametres characterising the accepted technology of works; - the main parametres characterising the technical devices of operation and control ; - information about the material, technical and personnel resources available at the mine; - mining and geological conditions of the deposit; - the facilities of the subsidiary units, of the mine; - the direct parametres and technico-economical indices in which the mine efficacy and activity is estimated. The suggested structure of the automatic operation system can be sensibly realized with the application of the microprocessor on the first level, the personal computer IBM PC/XT or PC/AT on the second level. For the complete realization of the project each mine will need 4-5 computers (as PC/XT), one IBM PC/AT and each mine complex - one super IBM for creation of the distributed information bank and its including in the integral world communication system.

Jan 1, 1992

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By D. D. Schlepp

There is a continuing debate about the influence of circulating load and classifier efficiency on the capacity of the circuit. Specifically, the effects of preferential classification, bypassed fines, and the sharpness of classification will be examined. Horizontal cyclones have also proven to be very successful in a number of operations but their impact on the circuit capacity has not been clearly defined.

Jan 1, 1990

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME) Inc., the president of SME formed Working Party No. 79, Ore Reserve Definition. Its mission was to develop guidelines for the public reporting of exploration information, resources and reserves. These guidelines were published in the April 1991 issue of Mining Engineering (pp. 379-384), and as a document entitled “A Guide for Reporting Exploration Information, Resources, and Reserves” in January 1992. Work continued on an ad-hoc basis until 1996. Working Party No. 79 was then renamed the SME Committee on Resources and Reserves and became a standing committee.

Jan 1, 1999

INTRODUCTION From its beginnings in the first decade of this century, flotation has gradually moved to a predominant role in mineral separation. There are several reasons for this, the continuing trend toward treat¬ment of lower-grade and more finely disseminated ores being the major one. Not only has this been true for sulfide ores to which the process was first applied commercially, but also for most nonsulfide ores as well. A second factor has been the broad applicability of the process with respect to particle size; it is effective from 8 to 10 mesh to below 10m. Finally, more so than for any other separation process, flotation has almost no limitations in separating minerals. Gravity, magnetic, or electrostatic processes are either applicable to particular minerals, or to a restricted number of mineral combinations. Flotation, on the other hand, can utilize the wide range of surface chemical differences among minerals, and an equally wide range of reagents. The recent availability of selective flocculation capabilities on a commercial scale as an adjunct to flotation should remove one of the limitations to the process in the very fine particle range. History Although flotation was anticipated in a 19th century patent to Haynes, its first significant industrial uses were in the early 20th century in Australia. According to Hoover,' the Pottter-Del-prat pro¬cess had a "measure of success" at Broken Hill's Block 14 mine in 1905-1906, and was definitely successful at the BHP Mine, where it produced 80,000 tpy of zinc concentrates. Both the Mineral Separa¬tion and the Elmore processes had early trials in Australia also, with both successes and failures. The first application in the United States was in 1911, when the Hyde process was used by the Butte and Superior Copper Co. on a zinc ore in Montana. By 1916 Hoover could list 46 applications to copper, lead, and zinc ores, mainly in the United States. Ten years later Taggart2 listed almost a thousand patents covering processes and reagents which with few exceptions laid the foundations for modern practice. Included were: sulfidizing of oxides; leach-precip¬itation-flotation; cyanides, sulfites, sulfides, and oxidants for selective depression of sulfides; starch, tannin, and glue as depressants; and xanthates, dithiophosphates, and oleic acid as collectors. Within an¬other 20 years, all of these were in commercial use along with amines for floating silica from phosphates, and synthetic frothers were com¬peting with pine oil and cresylic acid. Flotation machine development followed a different course. Of the 170 patents listed by Taggart in 1927,1 those incorporating film and oil flotation-about a third of the total-were no longer then

Jan 1, 1985

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By E. Barnard

Tarkwa Gold Mine is located in south western Ghana, and is majority owned and operated by Gold Fields Ghana Limited. The Tarkwa CIL plant utilises a single low aspect 27' x 42' 14MW dual pinion drive SAG mill designed to mill 4.2mtpa (525tph). The plant was designed and constructed in a manner that would facilitate its expansion to 8.4mtpa (1,050tph). Since the plant was commissioned in September 2004, the SAG mill has consistently exceeded its nameplate throughput by up to 25%. Through the installation of a 26? x 36? 14MW dual pinion drive Ball mill along with additional upstream and downstream equipment, the plant will now be expanded to 12mtpa (1,500tph). This paper endeavours to outline the process and engineering design challenges along with the future construction challenges of the expansion in the midst of a fully operational plant.

Jan 1, 2008

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By K. Oraee

Proven and probable coal reserves in Iran are estimated to be in excess of 5 Billion tons while the annual coal production is a mere 2 Million tons. Underdevelopment of the industry has proved higher production levels to be impossible, despite growing demand for energy supplies. The existences of numerous legislation are thought to have a detrimental effect on coal mining activities to the extent that some business entities have become uneconomical in many areas. This paper provides an analysis of the prevailing mining laws, policy making, legal frameworks and obstacles. It also outlines some other obstacles enshrined in the law and also highlights areas where foreign direct investment should be encouraged. The costs of lost opportunities are then estimated. The paper concludes by demonstrating that deregulations, amendments and in some cases complete abolishment of the incumbent legislations governing the coal mining industry will greatly enhance development of the industry. The analysis provided in this paper together with the results obtained, can prove useful to macro-economic policy makers both at local and national levels.

Feb 27, 2013

By R. J. Roman

Controlled and uniform distribution of the leach solution to a heap is of primary importance to achieving the desired rate of metal recovery and PLS grade from the heap. The step used to engineer the irrigation system are the same whether drips, wobblers or sprinklers are to be used. The mining rate, leach cycle time and heap height influence the heap cell size which along with the irrigation method selected controls the design of the irrigation system. The steps in the design procedure are explained as are the advantages and disadvantages of each irrigation method.

Jan 1, 1996

By J. D. Potts

Installation of a horizontal air blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong coanda effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector to bailing airflow ratio, and a 5.1-cm (2-in) gap between the shroud and ground. The shelf was 15.2-cm (6-in) wide and located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2009

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2007 draws upon available information from industry, literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2007: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia, and 2) information on regional and site-specific exploration activities that took place in 2007 and compiled by the USGS.

Jan 1, 2008

By H. H. Murray

Clay minerals are one of the more important industrial minerals. They are used in many products and because of different specifications may require special processing which can be either wet or dry. The clays discussed are bentonites, kaolins including ball clays, and palygorskite (attapulgite). In order to design a process flow sheet for these clay minerals, the physical, chemical, mineralogical, and optical properties need to be evaluated. Each species of clay minerals require a group of special tests which are described in this paper.

Jan 1, 2009

By Emily Wortman-Wunder

As the 2013 president of the Society for Mining, Metallurgy and Exploration, Inc., I am pleased to present the 2013 issue of the Transactions of the Society for Mining, Metallurgy and Exploration, Vol. 334. The timely publication of professional papers that promote the advancement of scientific and technical knowledge is critical for enabling technology transfer. SME plays a key role in this process through its publications. Communication within the mining community is the key to a successful profession and society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME; those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2013 Transactions contains 73 papers covering most every aspect of the mining life cycle and encompassing the diverse sectors of our industry including coal, industrial minerals, metals, health and safety and computational methods. It includes all 18 papers published in 2013 in the Technical Papers Section of Mining Engineering magazine (Vol. 65) and all 33 papers published in 2013 in Minerals & Metallurgical Processing (Vol. 30). Additionally, this volume contains 22 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. Some of the many research highlights from 2013 include discussions of perennial issues, such as how to adequately prepare the next generation of mining engineering students for the workforce (Frimpong et al., pp. 44-52) and how to predict and prevent coal mine bursts and bumps (Pariseau, pp. 60-68), the highly anticipated February Rare Earths issue of Minerals & Metallurgical Processing, and papers analyzing electrical injuries in the U.S. Mining industry (Homce and Cawley, p. 367-375) the latest in assessing the safety and efficiency of operations. All 73 technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2013 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2013

By Jeff Fontana, Daniel Ebin, Eric Westergren, William Currier

The PMott MacDonaldlane Train Tunnel West Extension (PTTWE) Project at HartsfieldJackson Atlanta International Airport includes the extension of the existing automated people mover system and terminal renovations at the baggage claim station. To assist with design, pricing, and assessment of risk on this progressive design-build project, 3D design models were prepared to increase visibility into realities of construction. This paper will focus on the original intent of the models and explore the additional, unforeseen value they provided throughout the design and construction process.

Dec 1, 2022