Search Documents

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By E. Cameron

Yeelirrie lies toward the center of Western Australia, 650 km (404 miles) northeast of Perth (Fig. 1). The ore reserves have been estimated as 52.5 kt (57,871 tons) of contained U3O8, at an average grade of 0.15%, of which almost two-thirds average 0.24% U3O8. the ore body is a thin, elliptical, more or less horizontal sheet measuring approximately 9 km (5.6 miles) in length, between 0.5 and 1.5 km (0.3 and 0.9 miles) in width, and up to 7 m (23 ft) in thickness, extending from the surface to a depth of 8 m (26 ft). In spite of its near surface position, there is only one small outcrop of significant mineralization. Carnotite is the only uranium mineral recognized so far, dispersed through a calcrete horizon, and deposited from circulating ground water which was also responsible for the carbonation of the clays completely filling an Early Tertiary drainage system. Calcrete, as seen at Yeelirrie, is quite distinct from the widespread, thin pedogenic horizons, as it often forms bodies many kilometers in length and up to 20 m (65.6 ft) in thickness, elongated parallel to the drainage lines. It is variously referred to as "valley calcrete" or "ground water calcrete" to emphasize the occurrence and mode of origin. The discovery of Yeelirrie in mid-1971 was the successful culmination of a grass-roots exploration program initiated in 1968 as part of Western Mining Cop's program of diversification from its historical position as a major gold producer. The object was simply to find an economic uranium deposit - with no constaints other than those normally taken as applying in the mineral search. There was, therefore, complete freedom in the selection of the exploration model, or models, to be applied and the areas to be considered, though the choice was inevitably influenced by both the nature of world occurrences and the local geology. One of the options avail- able was the sandstone environment. Yeelirrie was the direct result of pursuing this line of investigation through three sequential, but quite distinct, stages: first, a regional study; second, establishing a case for exploring the inland drainage systems of Western Australia; and finally, an evaluation of the calcrete environment. An assessment of the potential for sandstone-type deposits in Australia necessitated going back to first principles, since there were no known precedents in this country for guiding exploration and, as a consequence, the search need not be influenced by established prejudices. Previous uranium exploration during the 1950s had been preoccupied with vein-type deposits, and, although the sandstone environment was undoubtedly being examined in 1968, no discoveries had been announced to that time. When considering the necessary ingredients -a source of leachable uranium, a circulating ground water system, and a suitable reducing environment - it could be argued that considerable areas in the eastern part of the continent were theoretically prospective, but basin depth and the extensive superficial cover of Mesozoic and Cainozoic sediments presented considerable practical difficulties.

Jan 1, 1991

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, the U.S. Mine Safety and Health Administration (MSHA) began requiring the use of continuous personal dust monitors to monitor and measure respirable mine dust exposures to underground coal miners. Mines are currently using the PDM3700 personal dust monitor to comply with this regulation. After the PDM3700’s implementation, mine operators discovered that it interfered with proximity detection systems, thus exposing miners to potential striking and pinning hazards from continuous mining machines. Besides the PDM3700, other electronic devices were also previously reported to interfere with proximity detection systems. MSHA sought the aid of the U.S. National Institute for Occupational Safety and Health (NIOSH) and mining industry stakeholders to determine how the PDM3700 and some other electronic devices and proximity detection systems interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments and conducted laboratory evaluations. Some interferences were observed to be caused by electromagnetic interference from some electronic devices, including the PDM3700. Results showed that there was no significant interference when the PDM3700, as well as other electronic devices, and the miner-wearable component of the proximity detection system were separated by distances of 15 cm (6 in.) or greater. In the present study, it was found that the PDM3700 and the personal alarm device needed to be at least 15 cm (6 in.) apart in order for them to be used simultaneously and reduce potential interference. IntroductionUnderground coal miners are exposed on a daily basis to a variety of hazards, such as coal dust exposures, high noise levels, roof and rib falls, potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is that of operating or working near a continuous mining machine. According to U.S. Mine Safety and Health Administration (MSHA) statistics, 44 miners had been fatally struck or pinned by a continuous mining machine since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating continuous mining machines in underground coal mines, with the exception of full-face continuous mining machines, by 2018 (MSHA, 2015a)."

Jan 5, 2018

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By Donald H. Dowlin

The design of a preparation plant for minimum maintenance and clean up requires both the skills of the Engineer and the practical experience of the Operator. From the initial flow sheet and preliminary design until the plant is completed and operating, each phase of the work must be thoroughly explored for simplicity, workability and high efficiency. It is the responsibility of the Designing Engineer to develop the plant around the basic flow sheet, selecting equipment and materials not only with regards to Initial cost but also required upkeep and repair.

Jan 1, 1962

By TOMI GIORGIO DE, Ricardo Tichauer

Mineral exploration is a key factor for success in the mining industry. However, exploration best practices are often ignored in small-scale mining. This works presents the Tichauer-DeTomi Matrix, a methodology that measures the level of compliance of exploration programs in small-scale mining with the industry best practices. The matrix has been applied to three projects in Brazil: an artisanal gold mine in the state of Pará, a small-scale manganese project in the state of Bahia, and a small-scale manganese project in the state of São Paulo. The application of the matrix resulted in indexes that represent the level of maturity of the exploration program in each project and indicate priority actions for reduction of the geological uncertainty. Therefore, the Tichauer-DeTomi Matrix has shown potential to be a useful tool for assessment of geological uncertainty in small-scale mining. As a risk indicator, it may contribute to promoting investment in small-scale mining and development for communities that depend on this activity around the world.

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By Ellen Amoako Afful, Michael Moats, Guang Xu, Ashish Kakoria

Electrowinning and solvent extraction are crucial steps in the production of high-purity copper. However, safety concerns have been raised regarding the acid mist generated from the electrowinning process. The mist generated results in health risks to workers and damage to machinery and infrastructure. Currently, chemicals and pellets are used to control acid mist. However, the effectiveness of these controls may vary depending on the type of organic solvent used in the solvent extraction process, which can influence the generation of acid mist. This study aims to evaluate the impacts of organic solvents and surfactants on acid mist suppression. In this study, an electrolyte is contacted with organic solvents to simulate the solvent extraction. The electrolyte is dosed with 20 mg/L of surfactant at each contact. Acid mist testing is performed on the electrolyte separated from the organic phase at the end of the solvent extraction step. The mist collected is analyzed to determine the level of acid mist generated. The results of this study indicate that organic solvents and surfactants showed significant acid mist suppression, but with somewhat different suppression efficiencies. After first contact, Licorice and the organic, for instance, showed a suppression efficiency of up to 69.7% but its efficiency gradually decreased as the number of contacts increased.

Feb 1, 2025

By Cesar Carrasco, Heath Arvidson, Mark Forster

Block models built to represent the geology and rock characteristics of mineral deposits represent huge complex data sets, which form the basis of strategic and business planning, and public reporting of Mineral Resources and Mineral Reserves. Recent advances in cloud computing and database technology developed for the Internet of Things offer a different way of working with these critical data sets. Enabling a cloud based, open data structure with high performance data analytics capability presents a compelling improvement in governance and a democratization of ore body knowledge that can lead to automation use cases that support the digitalization of mining.

Jun 25, 2023

By J. W. Butwell

Anaconda has been active In the Bingham mining district near Tooele, Utah since 1914 when the company acquired International Smelting & Refining Co. Over the years both custom ores and complex Pb-Zn-Cu ores from the district were milled and smelted at International. In 1948 Anaconda acquired the property that covers the present Carr Fork ore body. Since that time active exploration took place in the 50's followed by detailed geological evaluation in the 60's. Convinced that high grade Cu deposits would be found at depth, a deep drilling program commenced in the late 60?s, with intersection of the ore zone in 1969. Following extensive deep drilling in the early 70?s, a feasibility study was conducted in 73-74 with board approval given Sept. 6, 1974. The 9,000 t/d mine-mill complex was budgeted at $217 MM over a 5 year schedule with start-up in Sept., 1979. The following discussion includes the concentrator and surface facility portion of the budget or approximately $60 MM of the scope. Special emphasis will be made on equipment selection and layout.

Jan 1, 1980

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By John Drew Ridge

Tables showing world trade in metallic mineral raw materials during the years 1953 through 1957 have been prepared for the following twenty-one commodities: alumina, aluminum, bauxite, chromite, copper concentrates, partly refined and fully refined copper metal, iron ore, pig iron, iron and steel (simple shapes), lead concentrates, lead metal, manganese ore, mercury metal, nickel ore, concentrates, and matte, nickel metal, raw pyrites, sintered pyrites, tin concentrates, tin metal, zinc concentrates, and zinc metal. In each instance, the amounts given by the importing country were used except when statistics from the importing nation were lacking, incomplete, or misleading. To show the considerable divergence between importing and exporting country totals for the same years, the complete mercury table is given and, in parallel columns, shows the comparable tonnages of importers and exporters. Tables for the other twenty commodities are presented in summary form. The data of the concentrate tables are used with those of the corresponding metals as a basis for a discussion of trade in concentrates versus trade in metals. The data of all twenty-one tables provide the basis for testing the thirteen rules governing international trade in metal raw materials which I first published in Mining Engineering for July 1955. Because the 1953 through 1957 data are far more complete and considerably more extensive than those on which the 1955 rules were based, it was found possible to deduce five additional rules and to modify three of the original thirteen appreciably. The full text of the eighteen rules is given.

Jan 1, 1960

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By D. R. McConnell

The seafloor in the US Pacific OCS and EEZ is enriched to varying degrees in critical and economically important minerals such as nickel, manganese, cobalt, copper, zinc, REY (rare earth elements plus yttrium), titanium, vanadium, antimony, gold, and silver. These mineral deposits take the form of polymetallic nodules on the seabed, cobalt rich ferromanganese crusts on seamounts and ridges swept clean of sediment accumulation, and seafloor massive sulfides formed by hydrothermal systems at geologic plate spreading centers and volcanic margins. Each of these mineral deposits form on or near the deep ocean seafloor where water depths are typically 4000 m to 5500 m and on the seamounts and volcanic arcs that rise from these depths. Commercial interest in deep sea mineral deposits and the potential for collecting or mining them began in earnest in the 1970s but has been heightened in the last 20 years as the international framework for developing these minerals in International Waters has matured that has coincided with forecasted rapid rising demand for minerals to supply energy and manufacturing needs for the green economy. Compilation reports published by academia, government, and private companies are reviewed to assemble data and assess the prospects for deep sea marine minerals in the US Pacific OCS and EEZ. Key compilations were made by the Circum-Pacific Council and USGS in the 1980s and 1990s. These, together with recent (2023) efforts by USGS to compile geochemical data from USGS affiliated marine research sampling cruises from the 1980s and 1990s, historical data maintained by NOAA National Centers for Environmental Information (NCEI), and recent publicly disclosed results from ISA contractors are used to inform the known occurrence and prospectivity for polymetallic nodules, cobalt-rich ferromanganese crusts, and seafloor massive sulfides in the US Pacific OCS and EEZ.

Feb 22, 2026

By K. Yatsunami

NKK has developed a new cold bonded pellet process. The features of this process are; 1) it is a continuous process with 10 hours curing. 2) Products can be used as materials for various metallurgical furnaces. 3) Various kinds of slag are used as binders if necessary. 4) The quality of products is excellent. The pilot plant completed in 1981 is now being successfully operated. We are also constructing a commercial plant at our Niigata works. We produced cold pellets containing carbon as material for ferroalloys (Si-Mn), by pilot plant and used them in furnaces. Consequently, considerable economic advantages were obtained.

Jan 1, 1984

By Malte J. M Gurgel

Subsurface spatial planning is becoming increasingly important in view of competing underground applications. This development is influenced by global agreements to reduce greenhouse gas emissions. Therefore, precise knowledge of the underground space is a basic prerequisite for future applications. The three-dimensional registration and reliable georeferencing of underground infrastructures can establish a holistic geodata basis for such tasks. Those tasks are discussed both for the development of energy projects such as deep geothermal energy as well as for storage applications. Research on geothermal energy has been carried out at RWTH Aachen University as part of the SuperC project in a license field in the Aachen area since 2001. Recently, this research has been extended to include monitoring aspects in the overlapping GEObservatorium Aachen field. The documentation and visualization of underground activities using photogrammetric methods like Structure from Motion is discussed based on recent research in sites for the final disposal of radioactive waste. Finally, both applications provide an outlook on supporting underground projects by using high-resolution geodata.

Feb 1, 2025

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016