Search Documents

By Edward S. Plotkin, Joseph D. Guertin

In a continuing effort to upgrade tunnel design and construction practice, the New York City Transit Authority sponsored a geotechnical monitoring program on a recently completed section of the E. 63rd Street line in mid-town Manhattan. The purpose of the program was to document rock behavior as well as temporary and final rock support systems to provide a possible basis for either confirmation or modificification to design methods and construction specifications. This paper describes those portions of the study associated with rock behavior and temporary support systems. The entire study included monitoring of rock movements above the tunnel as well as adjacent to a 36.6m (120 ft) shaft, monitoring of stresses in steel ribs, monitoring of loads in rock bolts in two test sections and monitoring of stresses in the final concrete lining. PROJECT DESCRIPTION Route 131-A, Section 4 is located in mid-town Manhattan extending from under the Central-Park Zoo on Fifth Avenue eastward under 63rd Street to the end of contract between Madison and Park Avenue. Figure 1 is a Project Locus Map. The contract included approximately 355m (1165 l.f.) of 4 track tunnel(13.4m (44 ft) wide by 13.7m (45 ft) high excavated dimensions) plus a 22.9m (75 ft) by 19.8m (65 ft) by 36.6m (120 ft) deep ventilation shaft. The entire tunnel and most of the excavation shaft was excavated in metamorphic rock, known locally as the Manhattan Schist. The depth to tunnel invert varied from approximately 27.4m (90 ft) at the west end of the contract to 35.Om (115 ft) at the east end. Rock cover above the excavated crown varied from approximately 6.7m (22 ft) at the approximate mid-point of the contract to 18.9m (62 ft) at the western end. A plan view and interpreted geologic profile are illus-

Jan 1, 1979

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst's bulletin1 on the Barite Resources of the United States.

Jan 1, 1971

By Arash Dahi Taleghani, Pooyan Asadollahi

Slurry walls, also known as diaphragm walls, are commonly used as temporary and/ or permanent support of excavation for construction of shafts in soft ground. Through case history, this paper demonstrates economical benefits of disregarding long-term structural contribution of the slurry walls particularly in severe environmental condition. In addition, for temporary slurry wall shaft systems, possibility of using steel fiber, synthetic fiber or additives in lieu of temperature/shrinkage reinforcement is discussed with detailed analysis. Finally, the paper will be concluded by introducing unreinforced slurry wall shaft system using newly developed/patented concrete additive.

Jun 13, 2021

By J. M. Keane

SMEThis loaner is concerned with important criteria relative to the design of small flota¬tion concentrators. For the purpose of this discussion a small flotation concentrator is defined as a facility having a designed ore feed rate of 1,000 metric tons per day (MTPD), or less. The decision to design and construct a small flotation concentrator is the culmination of a series of logical steps relative to the ex¬ploitation of a potential ore body. The information required for a rational and timely decision regarding plant design and construction is usually contained in a feasibility report. The information required in a thorough feasibility report has been summarized (1) (2) as follows: Type of mine or plant and proposed daily, monthly, and yearly production of all intermediate and final products. Quantity of indicated ore reserves. Location of project illustrated by a map showing surroundings, trans-portation facilities, and existing utilities.

Jan 1, 1980

NICOR Mineral Ventures, Inc. retained Neyer, Tiseo and Hindo, Ltd. to evaluate the potential effects of a planned dewatering operation at NICOR's proposed, 258-acre silica sand mining facility near South Rockwood, Michigan. The ?orebody? is a horizontally extensive, friable, quartz sandstone from the Sylvania Formation which also serves as an aquifer for some of the rural, residential development near the site. We conducted an aquifer test on the site which identified the important aquifer properties. Using these data and an analytical model, we determined that the radius of influence would be expected to range up to 6000 feet from the quarry during its final development stage. An inventory of water supply wells revealed that most wells had sufficient available drawdown and would not be adversely affected. A long-term groundwater monitoring program was recommended to monitor the possible effects at some of the closest wells.

Jan 1, 1987

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By J. D. Miller, J. Hupka

Important aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20-kg tar sand samples (Asphalt Ridge and Whiterocks, Utah) and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus, the tar sand porosity is a critical variable that determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, being still incomplete after 15 hours regardless of the ambient temperature.

Jan 1, 1994

By Bobby Michael (Mike) Roberts, G. M. (Mike) Bernard, Ronald R. Kelly

This paper describes Cananea's successful implementation of the world's first mobile high angle conveyor (MHAC™) to achieve multiple-lift stacking of their primary crushed (2,500 mtph) low-grade ore. The mobile high angle conveyor answered Cananea's needs to stack a second lift, 30-meter high, on their Quebalix I pad. The mobile high angle conveyor is a custom unit that was designed by Terra Nova Technologies (TNT) in conjunction with Continental Conveyor and Equipment Company (CCE's 100th HAC). The stacking system expansion project also includes a rail mounted tripper on the existing overland conveyor and a custom designed "corridor conveyor" to build the corridor for the upper mobile HAC tracks and tail of the existing mobile stacking conveyor. Mexicana de Cananea, part of Grupo Mexico, is a large copper producer in Sonora Mexico and has been in operation continuously for over 100 years.

Jan 1, 2002

By Rongjie Kong, Shiwei Wang, Dongjiao Gui

Metal cations have significant effects on the flotation of coal and minerals. In this study, the effects of monovalent cations ( Na+ and K+) on the flotation of low-rank coal (LRC) were investigated using flotation and particle–bubble attachment experiments and through X-ray photoelectron spectroscopy (XPS) and molecular dynamics simulations. Oleic acid (OA), methyl linoleate (ML), hexadecyltrimethylammonium chloride (CTAC), ricinoleic acid (RA), and kerosene were used as flotation collectors. The flotation experiments revealed that the flotation yields of LRC improved when OA, ML, RA, CTAC, and kerosene were used in pure deionized water. However, flotation was suppressed for these collectors in the presence of K+ and Na+ ions. In contrast, when using CTAC, the flotation yield increased in the presence of these ions. Specifically, the flotation yield increased from 41.24 to 87.03% when 2.0 kg/t CTAC was used in 10 mmol/L NaCl solution. Particle–bubble adhesion experiments and XPS revealed that the hydrophilic groups of CTAC were adsorbed on the LRC surfaces by electrostatic forces, whereas the oxygen-containing functional groups of OA, ML, and RA formed hydrogen bonds with the LRC surface in pure water. Finally, the simulating result revealed that the hydrophobic ends of the OA, ML, and RA collectors hinder the flotation of LRC by adsorbing monovalent cations, whereas the adsorption of monovalent cations on the hydrophobic end of the cationic surfactant (CTAC) promotes flotation via strong electrostatic interactions.

Jan 31, 2024

By Donald W. Gentry

The evaluation of industrial minerals deposits for investment decision making follows the same basic principles that apply to metallic deposits. For example, the quantity and quality of the mineral occurrence is assessed, engineering/economic feasibility studies are performed for various production scenarios, project evaluation criteria are calculated for each alternative, and finally, an investment decision is made. A more specific evaluation-related example of commonality between metallic and nonmetallic deposit assessment relates to the various parameters which impact project feasibility studies. There exists a suite of pertinent factors which must be considered, studied, and analyzed when evaluating any mining property. Table 1 is an outline of some, but certainly not all, of the various factors which should be considered when preparing feasibility studies on mining properties. Most analysts agree that all the factors listed in Table 1 should be assessed to some degree in at least one of the feasibility studies prepared during the property's evaluation period.

Jan 1, 1984

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

By Moussa Wone, William Levy, Christopher Caruso, Zachary Spera, Thomas Hennings, Richard Stacy Kinchen, PE Joel Kantola

"Owners constructing new combined sewer overflow (CSO) systems increasingly seek to have project design lives of 100 or more years in response to the growing size, complexity, and cost to construct and operate these systems. However, a codified and universally accepted approach to achieving this goal in the United States does not currently exist since service life prediction is a relatively new technical field. This paper discusses how the 100-year design life requirement was met for the design of tunnels, drop shafts, and diversion structures in the DC Clean Rivers Program (DCCRP). The authors identify some commonly referenced publications, present the testing framework used by the program manager to characterize the CSOs, review the design criteria used to guide the 100-year design life development, and establish guidelines to be considered by program managers and designers when implementing similar extended design life requirements in other CSO control programs.INTRODUCTIONLike many older cities in the United States, the sewer system in the District of Columbia consists of both combined sewers and separate sanitary sewers. When the capacity of a combined sewer is exceeded during storm events, the excess flow, which is a mixture of sewage and storm water runoff, is discharged to the District’s receiving water bodies (Anacostia River, Potomac River, and Rock Creek) and tributaries through outfall structures. This excess discharge during storm events is called a combined sewer overflow or CSO. A total of 53 CSO outfalls for the combined sewer system are listed in DC Water’s National Pollutant Discharge Elimination System (NPDES) Permit issued by the U.S. Environmental Protection Agency (EPA). The DC Clean Rivers Program (DCCRP) will reduce the number of CSO outfalls into the Potomac and Anacostia Rivers and decrease flooding in DC neighborhoods during extreme rain events by capturing, storing, and conveying diverted CSOs to the Blue Plains Advanced Wastewater Treatment Plant."

Jan 1, 2016

By C. R. DeGennaro, Yongjun Zhang, J. Bickson, J. L. Carr, Chenming Zhou, J. R. Srednicki, B. Lambie, M. Girman, J. A. Galanko

Between 2005 and 2021, surface mining haul trucks were involved in 54 fatal incidents in the United States [1]. Collision warning and avoidance systems (CXS) can help haul truck operators navigate their route safely. The evaluation of CXS object detection performance for surface mining haul trucks relies on the positional accuracy of the ground truth instrument. As part of a holistic approach, researchers from the National Institute for Occupational Safety and Health (NIOSH) characterized the accuracy of a global navigation satellite system (GNSS) that serves as the ground truth instrument to determine object position and velocity in CXS object detection performance testing. We used precision surveying equipment to establish ground truth points for comparison with GNSS data collected for static positional measurements and reduced-scale straightline vehicle dynamic tests. We conducted these tests with real-time kinematics (RTK) and then satellite-based augmentation systems (SBAS). For the dynamic tests, we measured a distance error of 1.34 m (4.40 ft) using RTK and 1.50 m (4.92 ft) using an SBAS. This research will provide CXS manufacturers and CXS researchers a basis for evaluating the positional accuracy of CXS. Note that we did not evaluate any CXS in this experiment.

Feb 1, 2024

By D. Sinha

Mine investment decisions involve both objective and subjective criteria. The subjective criteria are efficiently decided by interaction with company experts. The Expert System approach can incorporate knowledge of experts and interact with conventional computer programs on mine evaluation. Artificial intelligence offers considerable opportunities in comprehensive mine investment decision making process.

Jan 1, 1998

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By W. M. Tupper

[The two types of sulfide deposits in the Bathhurst Newcastle area are; (a) epignetic fissure deposits, and (b) massive sulfide deposits. Geological evidence has been variously interpreted to suggest a syngenetic origin, a source bed' origin, or a magmatic hydrothermal origin for the massive sulfide deposits. Sulfides disseminated through the black shales and argillites of the host rocks are enriched in S32 (mean value 22.34, S34. = 5.8 per mil) relative to the meteoritic standard of 22.21, and have a broad spread in range of values. S32/S34 ratios of sulfide minerals from the deposits occur in two distinct groups. The massive sulfide deposits exhibit ratios between 21.88 to 22.05, while the fissure deposits exhibit ratios between 22.18 and 22.21. These results suggest two separate sources for the sulfur, each, however, resulting in magmatic hydrthermal deposition because of the narrow spread of ratios in each group. Granite intrusive into the host rocks of the sulfide deposits have a mean K/A age of 386 ± 10 M.Y. Lead minerals in the sulfide deposits have a mean nodel lead age of 370±20 M. Y. Thus the lead minerals and the granite bodies were emplaced during the same major orogenic event. Sulfide minerals from magmatic hydrothermal deposit have a very narrow range of S32/S34 values, as do those of the Bathurst area. It seems reasonable, therefore, that well homogenized magmatic hydrothermal solutions are the most logical source of the sulfide deposits. Furthermore, the homogeneity of the lead isotopic abundance data gives strong independent evidence that the ores are of a magmatic hydrothermal origin.]

Jan 1, 1960

By MOHAMMAD R. H. GORAKHKI, CHRISTOPHER BAREITHER, MANUEL APARICIO, IV JOSEPH SCALIA

Comingling filtered tailings and waste rock in a tailingsdominated mixture is a mine waste management strategy that has the potential to create geotechnically and geochemically stable landforms. Potentially acid-generating (PAG) waste rock can be sequestered within a filtered tailings matrix to enhance water retention and decrease hydraulic conductivity relative to a waste rock pile, potentially minimizing acid rock drainage (ARD). Enhanced water retention can reduce oxygen ingress limiting oxidation and resultant acid generation. Reduced hydraulic conductivity can slow inward percolation and outward drainage. In dry climates, the tailings matrix can hold precipitation near the ground surface accessible to evaporation and transpiration, thereby decreasing percolation. This paper presents an evaluation of comingled filtered tailings and waste rock in a tailings-dominated mixture (termed GeoWaste herein) and illustrates that ARD can be reduced under field conditions in a subtropical–highland climate.

By Stephen J. Brower

Located in Central Nevada, The Round Mountain Gold deposit has been continuously mined since 1977. Present proven and probable reserves are 226 Mt (250 million short tons) at 1.1 g/t (.032 oz per short ton). The current open pit mining rate of 118 Kt (130,000 short tons) per day is producing 41 Kt (45,000 short tons) per day of ore to be processed by heap leach methods. At this rate, the current reserves provide a 16 year mine life. The high mining rate and strict ore delivery requirements mandate comprehensive and realistic mine planning. The mine planning process is described in three general steps: Deposit Modeling; Mine Design; and, Production Coordination and Support.

Jan 1, 1989

By R. Berton, M. Walden, S. Melberg, N. Rocco

Recent tailings dam failures around the globe have influenced many mining industry regulators to reassess their requirements for the numerical modelling of tailings dam failures. This type or forward modelling is associated with overarching uncertainties as the model cannot be calibrated against a physical result. Dam breach analyses that meet the requirements of current industry standards and guidance typically begin with identification of credible failure modes and selection of appropriate topographic data set to represent the study area. The breach parameters and the volume of tailings released are then determined using available methodologies and empirical relationships. Subsequently, when the breach hydrograph is developed and the hydrology of stream networks are complete, the runout simulation is implemented. Due to the uncertainty involved in the process, sensitivity analyses are recommended to quantify variations in model inputs on the inundation extent and the flow characteristics. This paper outlines some common methodologies utilized for development of dam breach models, summarizes associated uncertainties with these methodologies and inputs, and provides guidance on how sensitivity analyses can address a wide array of uncertainties inherent in tailings breach analyses. This paper provides an understanding of how selecting appropriate breach parameters can result in reasonably conservative inundation extents consistent with the identified credible failure modes.

Mar 2, 2022

By I. Martinez-Dominguez

In September 1992, mining in Mexico was opened again to foreign investment by President Salinas-de Gortari, after thirty years of "Mexicanization" of mining industry which limited foreign participation up to a 49 % (or 34 % in case of national reserves) on a Mexican mining corporation. During said period mining in Mexico was controlled by four or five big mining companies and besides mining production was focused mainly on silver, lead, zinc, copper and fluorspar. Suddenly in middle of a big crisis on Mexican mining industry due to low prices of minerals in the world and also in a period on which it seems that mining industry in the United States and Canada has been condemned to die for environmental reasons, it appears a new Mexican Mining Law to permit foreigners to participate in mining in Mexico' trough Mexican mining corporations that they may control up to 100 %

Jan 1, 1994