Search Documents

By Paul H. Earl

This paper discusses the evolution of a modeling methodology for explaining price behavior in the aluminum industry. Three generations are described, each utilizing as a foundation a microeconomic stages-of-processing approach. The second generation represents an improvement over the initial version, by incorporating more rigorous specifications of energy cost, and market strength (demand-supply balance) as well as endogenous treatment of market strength. International linkages across prices, costs, and markets, are the major extensions in the third generation. The discussion covers theoretical considerations, data problems and limitations, and model specifications. Simulation and forecasting properties of the models are also addressed.

Jan 1, 1979

By Tom B. Corry

INTRODUCTION Located approximately 48 km (30 miles) south of Dallas, Texas, use to be the site of the Superconducting Super Collider. For those of you unfamiliar with the project, this was a multi-billion dollar project taken on by the U.S. Government for the further advancement of technology, medicine, and science. Major components of the project consisted of a Linear Accelerator known as the LINAC; three accelerating rings known as the Low Energy Boosters (LEB), Medium Energy Booster (MEB) and the High Energy Booster (HEB); the East and West Campuses where the Inner Reactor Halls would have been located; and the 87 km (54 mile) main collider tunnel. Unfortunately, this all came to an end on December 6, 1993, with the termination of the project due to the Government's cancellation of funds. This paper will deal with the two of the underground contracts before the termination. These two contracts were the 1122 contract which ran from N25 to N40 and the 1130 contract which ran from N40 to N55. (See figure 1) The 1122 contract was awarded to us in July of 1992 and consisted of the excavation and support of six (6) shaft varying in diameter from 5.5 m (18 feet) to 8 m (26 feet) and ranging from 39.6 m (130 feet) to 61 m (200 feet) deep and the driving of approximately 13,100 m (.43,000 If.) of main collider tunnel. Our second contract, the 1130, was almost identical to our first

Jan 1, 1995

By George W. Heunisch

The properties of Neutra-Fix® and Neutra-Ment® , two new lime substitutes for the treatment of acid mine drainage (Arm), have been compared with lime and Alkament®, two products presently in use for AMD treatment. The two new products are basically dolomitic byproducts and produce sludges that are more compact than those from lime. Sludge settling rates are faster than lime with iron concentrations after 24 hours that comply with EPA regulations. Material utilization and optimum pit are reported.

Jan 1, 1984

By Gunnar Nord, Per-Anders Persson, Duri Prader

The paper gives a short resumé of the findings of the joint US - Swedish "Mechanical Boring (MB) or Drill and Blast Tunneling (DB) ? Workshop" in Stockholm December 1976. New developments and trends in both MB and DB techniques in Europe since 1976 are described, and information is given on some interesting new projects. Differences in contracting principles between the US and Europe lead to different practices for preinvestigations, design, excavation and arbitration and legal affairs. It is shown that this often leads to a higher cost in the US than in Europe for similar excavation jobs. A typical US tunnel job also has more men on the site than a similar job in Europe. This adds to the cost difference and is only partly balanced by a slightly higher rate of excavation in the US. A comparison is made between two quantitative methods of predicting MB penetration rates. These are in reasonable agreement. A probable future development in machine design is an increase in cutter load towards perhaps 25 tons per disc where the tunnel diameter is large enough to house the machine size dictated by the size of the very large electric motors required. Recent European developments in drill and blast technique include improved methods for cautious blasting, precision hydraulic drilling of small diameter holes, and non-electric interval blasting techniques. These developments still keep the drill and blast method ahead of mechanical boring costwise for tunnels in igneous rock whereas for most sedimentary materials mechanical boring has a lead, particularly for long tunnels.

Jan 1, 1979

By Y. M. Jiang

Many underground instabilities, such as excessive shield loading and roof falls, occur at longwall faces causing safety problems and production losses. Such instability problems are directly related to roof conditions which can be categorized using geological information. . However, most geologic information describing anomalies and variations of immediate and main roofs are not available before mining resulting in unexpected problems in a longwall face. It is apparent that the evaluation of these geologic anomalies provides a great benefit for longwall stability. The purpose of this study is to evaluate roof categories associated with geological anomalies employing fuzzy set theory. The evaluation is based on real-time monitoring information, such as shield leg pressure, developing load on shields, intervals of periodic weighting, and the ratio of developing loads during periodic to normal times. This paper introduces the application of fuzzy set theory for characterizing roof conditions and evaluating of roof similarities.

Jan 1, 1995

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By Michael G. Zabetakis

Effective accident prevention programs utilize a broad spectrum of activities, including meaningful training programs. In practice, such programs must be directed towards specific, defined needs. These needs are considered here for three categories of employees: new, re-assigned, and experienced.

Jan 1, 1983

By XUEWEN WANG, Changda Zhang, Huaguang Wang, Mingyu Wang, Bin Hu

The copper smelting process produces plenty of copper slag every year, which is a hazardous solid waste, but a secondary resource. In the present study, the extraction of copper, nickel, and cobalt from copper slag was investigated through the process of sulfation roasting–water leaching and the process of sulfation roasting–sulfate decomposition roasting–water leaching respectively. Compared with the process of sulfation roasting–water leaching, the process of sulfation roasting–sulfate decomposition roasting–water leaching is a better choice, which could not only get almost the same leaching of copper, nickel, and cobalt as the former process, but has a lower leaching of iron and aluminum. For the process of sulfation roasting–sulfate decomposition roasting–water leaching, the leaching of Cu, Ni, and Co reached up to 74.2%, 71.1%, and 69.6% respectively, under the optimal conditions including sulfation roasted with 80 wt% sulfuric acid addition at 200 °C for 60 min and sulfate decomposition roasted at 650 °C for 60 min, followed by water leached at 90 °C for 30min with a liquid–solid ratio of 2 ml/g. The leaching of Fe and Al was only 4.9% and 17.6%.

May 4, 2020

Reaction kinetics for gold dissolution in acid thiourea solutions were investigated using formamidine disulfide as an oxidant. For the conditions studied it appears that a surface reaction limits the rate of gold dissolution. The rate was found to be first order with respect to thiourea concentration and half order with respect to the concentration of formamidine disulfide; the apparent activation energy for the reaction was 10.40 kcal/mol (43.40 kJ/mol); and the reaction rate was independent of pH for the pH range 1.0 to 3.0.

Jan 1, 1999

By J. D. Miller

Many factors -- political, environmental and technological -- will determine the extent to which the United States realizes the potential of its vast coal resources. Not the least of these factors is technogical development including mining, processing and transportation. With regard to processing technology, about 50% of the 800x106 tons of coal mined annually in the U.S. is processed in preparation plants. The purpose of the physical separations accomplished in these preparation plants is to remove ash (present as clays and other oxide minerals) and sulfur 'present mostly as pyrite). Coal flotation circuits for such separations are becoming more important in the processing of minus 28 mesh coal. (1,2,3) For example in the U.S. in 1960, 31 flotation plants processed 26,500 tpd; whereas in 1980, there were 80 flotation plants which processed 78,300 tpd. This corresponds to an annual growth in flotation plant capacity of 10 per year during the past two decades. Coal flotation is based on the natural or induced hydrophobicity of coal particles which are separated from hydrophilic ash and sulfur constituents by attachment to air bubbles. The coal particle/air bubble aggregates are collected in a froth phase which is created by the addition of a suitable frother such as MISC. Without exception, such separations are made in a conventional flotation cell, which, in essence, is a stirred tank reactor with a shrouded rotor to shear the air as it passes through a hollow shaft. The dispersed air bubbles (4.0 mm diameter) are stabilized by addition of the frother. Collision of the air bubbles with, and/or precipitation of the air bubbles on, the coal particles results in the formation of coal particle/air bubble aggregates which rise in the gravitational field and are collected in the froth phase developed at the top of the flotation cell. Restraints on successful separation by this conventional flotation technique are particle size and retention time. Generally it is found that effective flotation is only achieved for particle sizes between 10 and 1000 microns. Further, with respect to retention time, it is found that a nominal retention time of at least 2 minutes is required for successful separations. These facts limit the effectiveness of conventional coal flotation. Coal fines may be lost in the reject stream and disposal is frequently a problem. The retention time required for conventional flotation results in large floor space demands which limit the capacity of the plant.

Jan 1, 1981

By T. O. Kuhl

The Royal-Mountain King Project is 7.2 kilometers (4.5 miles) northwest of Copperopolis, California. Reserves of 8,250,000 t (9,100,000 st) at 2.32 g/t (0.068 oz/st) gold will be processed at 2500 t/d (2750 st/d) from three pits. Production is scheduled to begin the first quarter of 1989. District geology consists of northwest trending sequences of Jurassic meta-sedimentary and meta-volcanic rocks. Three ore bodies are located along the Hodson fault which trends northwest and dips 40 degrees northeast. The Gold Knoll and North Pit ore bodies are hosted in carbonate and silica altered meta-volcanic rocks whereas the Skyrocket ore body is hosted in quartz stockwork zones in meta-sedimentary rocks. Gold is present as inclusions and micro-veinlets in pyrite.

Jan 1, 1989

By John J. Dran

In recent years, market rates of interest have risen well above their historical long-term average. Also during this period, the short-term variability of interest rates has been greater than in prior years. Interest rates have a significant effect on the operation of our economy. They influence the extractive industries in a number of ways. Their major long- range impact is on investment decisions - specifically the valuation of mineral deposits. An understanding of the factors that influence interest rates is important to the engineer or businessman who makes the investment decisions for the mining company. The effect of changes in the market rate of interest on the value of mineral reserves is critical to the future financial success of the mining enterprise. The most common simplification of the factors determining the level of interest rates is that they are a function of the demand for and the supply of money. While this is an oversimplification, most businessmen would be hard- pressed to provide a better explanation. The purpose of this paper is to explore certain fundamental economic aspects of interest rates and to examine their effect on the analysis of investment in mineral deposits.

Jan 1, 1975

By S. S. Peng

To prevent mine floor heave, the mechanisms of floor heave must be fully understood. Based on the field study, the mechanisms of two types of floor heaves are analyzed in this paper. The mechanical models for the two types of floor heaves are developed. The floor heave can be predicted by the developed mechanical models and the control measures are recommended.

Jan 1, 1995

By K. N. Han, H. C. Cho, R. Kim

"As an extension of the work on the effect of OH- on various cations in hydrometallurgical systems, the effect of Cl-, Br-, I- and CN- on cations such as Ag+, Cd2+, Hg2+, Cu+, Cu2+, Co2+, Zn2+, Pb2+ and Sn2+ has been examined in detail. The Newton-Raphson technique has been used to determine the amounts of various metal species as a function of the concentration of anions. Some practical implications of various metal complexes in metal separation and removal from solutions have been examined and discussed.IntroductionUnderstanding the role of anions in hydrometallurgical processes often determines the success of an operation. The successful choice of concentration and type of anions not only leads to an effective extraction and removal of metals (Esmaeili et al., 2005; Brbooti et al., 2011; Wei et al., 2005; Jeppesen et al., 2009; Al-Tarazi et al., 2004), but also to assisting effective separation of various metals, whether it is a solvent extraction, ion exchange operation or even a simple precipitation (Farha et al., 2011; Sevenich and Fritz, 1983; Rashid, 1974).This paper continues the discussion of the role of anions in hydrometallurgical systems beyond the role of OH-, which was the topic of a previous paper (Kim et al., 2014). Table 1 lists various anions that are frequently used in conjunction with metal ions to be selectively separated or precipitated. As seen in the table, many anions are used frequently in hydrometallurgical practices. Some of the more frequently used anions include OH-, SO4 2- and CO3 2-. The halogen elements, Cl-, Br- and I- , as well as CN-, are also used in hydrometallurgical applications, especially in relation to noble metal recoveries (Meng and Han, 1994; Zhang et al., 1996; Sun et al., 1996; Starovoytov et al., 2007)."

Jan 1, 2015

By William Hodder, Ehsan Alavi, Nader Ghasempour, Daniel Cressman

The Don River & Central Waterfront Coxwell Sanitary Bypass Tunnel (CBT) Project in Toronto will extend approximately 10.5 km from Ashbridges Bay Treatment Plant west under Lake Shore Boulevard, north under Bayview Avenue and east through the Don River park area to the Coxwell Ravine Park. The tunnel is currently being mined by using a shielded dual-mode tunnel boring machine (open and close) capable of operating in EPB mode and lined by using a precast concrete segmental tunnel linear with an internal diameter of 6,300 mm and external diameter of 6,900 mm. The CBT is expected to be excavated mainly through shale bedrock of the Georgian Bay Formation, at approximately 50 meters deep. The tunnel crosses a buried bedrock valley in two locations, in the southern portion of the alignment, adjacent to the Don River, and at the northern portion of the alignment approaching the CX-1 shaft. In these two locations, the bedrock cover is expected to be less than 6 meters. The risk of encountering weathered bedrock, significant ground water inflows or surficial soil deposits through these buried valleys was identified during the design phase. The contract required the TBM to be designed with the ability to probe drill ahead of the TBM and convert to EPB mode if necessary, to cross this area. This paper will discuss the additional exploration that was performed by the contractor to identify the extent of this buried valley, the plan going into the zone of potential weathered shale, and the actual conditions encountered.

Jun 13, 2021

By Paul H. Johnson

Chemical mining may be defined as the in-place extraction of metal values from ores located within the confines of a mine (that is, broken or fractured ore, stope fill, caved material, or ores in permeable zones) or ores located in dumps, prepared ore heaps, or tailing ponds. The term solution mining has, in general, been used to mean the in-place dissolution of water-soluble mineral salts with leach solutions. Chemical mining is presently in its embryonic stage. Basic research needs to be done to understand the influence of physical and chemical factors in chemical mining, and applied research needs to be done on both a small and a large scale to develop practical techniques of field practice. The areas of research include the following: (1) Leaching chemistry, the influence of physical, chemical, and biological factors in in-place leaching (2) Hydrodynamics of chemical mining systems (3) The development of new, as well as old, leaching agents for use under chemical mining leach conditions (4) The development of new means of contacting fine and coarse materials (with solutions) under static leach conditions (5) The development of new processes for generating and regenerating chemical mining leach solutions (6) The development of metal recovery processes

Jan 1, 1969

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By John P. Mahaffey

Thank you Mr. Chairman, Ladies and Gentlemen of SME-AIM? for this opportunity to talk to you about, one of the most interesting and challenging facets of our mining industry. Because the need was then -we built in 1964 what is still today, one of the most sophisticated AC mining machine simulators for this or any industry. It simulated the electrical controls and circuits of an AC shuttle car. The student activated the controls on the main console, which represented the elementary control and power circuits. Its accompanying slide-tape program, student manual and worksheets provided our customers with an effective and highly motivational means to teach their face mechanics: 1. practical AC circuit and motor theory 2. print reading 3. troubleshooting techniques Nearly 10,000 men have put in over 100,000 manhours of training on the AC panel and its DC counterpart. The DC panel was modeled after the 14BU10 Loader. The success of these larger panels pointed out the need in our industry for an orangized, basic electrical program designed around mining machinery components & circuits. But probably more importantly, they brought to light the tremendous thirst for upgrading by our industry's employees. We then turned our attention to developing programs around very basic panels. The resulting programs were designed also to assure maximum student involvement.

Jan 1, 1975