Search Documents

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that, overall, the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In common practice, however, coal blending is at best coal mixing. If necessary, more sophisticated blending systems can produce a more homogeneous feed by using accurate weighing devices and on-line coal analyzers coupled with sampling systems. Blending can be accomplished at the mine, on stockpiles, and from bins, bunkers, and silos.

Jan 1, 1994

By Harry H. Peek

Artesian pressures of unusual magnitude occur in the deeper aquifer units beneath a considerable part of southeastern North Carolina and extend into South Carolina. The high pressures were first observed in 1968 in wells near Wilmington that were drilled to "basement" rock and which were screened between depths of about 260 to 300 m (meters). The pressure was recognized by Peek and Heath1 as an anomalous geo-pressure and unrelated to recharge conditions in the region. Since 1973, much new information has been obtained on hydro-geologic conditions in the area and a preliminary report on the deep artesian pressures was published in 1975.2 Most of the basic information has been obtained from groundwater research stations constructed by the Groundwater Section of the North Carolina Department of Natural and Economic Resources as a part of Ground-water studies in the Coastal Plain Region. These stations consist of an exploratory well drilled to basement rock with wells completed in each principal aquifer unit to provide data on aquifer characterestics, water levels and water quality.

Jan 1, 1977

By Jean-Luc Cornet

Downhill, or regenerative conveyors have always been a challenge to the design engineer due to their natural instability under load. The last decade has seen the appearance of high tonnage, high negative lift conveyors with several hundred meters of drop. These conveyors have made necessary the development of new braking systems and intelligent drive controls to address their starting and stopping requirements under various load conditions. This paper describes the critical design criteria of large regenerative conveyors and some of the advances in mechanical braking systems and drive control technology developed by Conveyor Dynamics, Inc. (CDI) to address their specific requirements.

Jan 1, 1993

By R. Asamoah, P. Forson, W. Skinner, M. Zanin

Despite the seeming benefits decoupling pyrite and arsenopyrite minerals present in practice, little success has been achieved. The present study presents possible process routes for attaining selective flotation broadly capitalizing on differential oxidation between these minerals, and the use of a chelating collectors. The best performance was achieved with dithionocarbamate application following copper activation, yielding 81.4% arsenopyrite and 37% pyrite recovery. Preaeration followed by staged addition of xanthate produced 76% arsenopyrite and 31% pyrite recovery while reverse flotation of pyrite after H2O2 addition gave rise to rejection of 66% pyrite accompanied with 24% arsenopyrite.

Mar 2, 2022

By Karl V. Lindell

Asbestos is not the name of a distinct mineral species, but rather the commercial term applied to the fibrous form of several minerals differing widely in composition. There are some 30 known varieties of asbestos but of this number only 6 are of economic importance, and these, in order of economic significance are chrysotile, crocidolite (or blue asbestos), amosite, anthophyllite, actinolite and tremolite. Chrysotile asbestos was formed by the introduction of hydrothermal solutions into fractures in serpentinised ultrabasic host rocks. These solutions dissolved magnesium silicate from the wall rocks, and with subsequent lower temperature and pressure they became supersaturated, and crystals of chrysotile asbestos formed. The chemical composition is variable but is classified as a hydrous magnesium silicate, containing a high percentage of magnesia and water, plus varying amounts of alumina and ferrous and ferric iron. Other asbestos minerals are formed by a similar process but with a different host rock e.g. crocidolite occurs only in iron' formation. The chemical composition of asbestos minerals other than chrysotile, shows a wide variation, but in general may be classified as silicates, or metasilicates, containing varying amounts of calcium, magnesium, sodium and iron.

Jan 1, 1964

By J. C. Judd

The U.S. Department of the Interior, Bureau of Mines investigated solvent extraction methods for recovering gallium from filtrates produced from sulfuric acid leaching of hydrometallurgical zinc residues. These filtrates typically had pH values of 0 to 0.5, too high an acid content for effective gallium recovery by traditional extractants. Of the nine extractants studied in batch tests, 0.3M octyl phenyl acid phosphate (OPAP) in a kerosene diluent was the most effective extractant for gallium recovery, extracting up to 99.9 pct of the gallium. This high extraction was possible when the iron in solution was maintained in the reduced ferrous state. Batch tests also showed that a 1.5M-H2SO4 strip liquor recovered 98 pct of the gallium from the loaded OPAP. A continuous solvent extraction system was designed and operated based on McCabe-Thiele analyses of equilibrium loading and stripping isotherms. When 12 L of leach filtrate containing 0.32 giL Ga and 20 giL Fe were pumped through the system in 32 hr, results showed that 95 pct of the gallium was extracted in four stages at an A:O ratio of 1:1. Stripping the loaded solvent with a 1.5M-H2S04 liquor recovered 94 pct of the gallium in four stages at an A:O ratio of 1:4. A two-stage, 50-pct-phosphoric acid strip successfully removed ferric iron from the OPAP, allowing high gallium extractions to be maintained.

Jan 1, 1990

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971

By Paul M. Keyser

Flotation columns continue to offer improved metallurgical and economic advantages over other flotation methods. Pilot testing at Ozark-Mahoning Co. in Rosiclare, IL led to installation of one 2.3-m-diam (7.5-ft-diam) column for zinc roughing and one 1.1-m-diam (3.5-ft-diam) column for zinc cleaning. This circuit replaced one stage of mechanical roughing-scavenging followed by two stages of cleaner flotation. General Column flotation continues to make inroads into applications traditionally dominated by mechanical flotation cells. For example, columns are becoming more visible as rougher flotation devices. At Royal Mountain King Mine in California, two 2.9-m-diam (9.5-ftdiam) columns are used for rougher flotation of carbon from a gold ore (Orlich et al., 1992). In addition, work performed at BRGM in France demonstrated the superiority of column flotation over mechanical flotation with respect to design of new plants (Morizot et al., 1991). The primary reasons for this acceptance of columns are a general improvement in design, scale-up and operation, as well as improvements in sparger design and performance. With these advances, the full benefits of column flotation can be realized. The benefits of properly designed, aerated and operated flotation columns include lower capital costs, reduced operating costs, fewer processing stages and improved metallurgical performance.

Jan 1, 1993

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991

The viability of physico-chemical purification methods such as selective flocculation for separation of two components having similar chemical composition and same crystal structure but different surface properties is demonstrated. Loss of selectivity was observed in a dolomite-dolomite mixture with Polyethylene Oxide (5 million molecular weight) as the flocculant. Hetero-flocculation was minimized using a low molecular weight PEO (MW -105) as the site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at 100% recovery level.

Jan 1, 1993

By H. H. Hayden

The accident repeater-40 you have one at your mine? Unless your company is vastly different from most coal companies, you will find that a small percentage (11-12%) of your employees will have a large percentage (47-50%) of your accidents. When you find out that this is a fact, what do you do? First, you establish a set of guidelines that can be used in identifying the ?accident repeater?. Next, you determine the type of action necessary to improve work habits and safety performance of the accident repeater. With these two steps in mind, objectives are developed for an ?accident repeater? program.

Jan 1, 1984

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By Ken E. Baylis

Current over-capacity in coal production provides assured and relatively low-cost supplies to coal importers. At the same time, it is of serious concern to coal producers who invested considerable sums in the expectation that overseas demand would continue to grow rapidly. This paper assesses the reserves available for export, the export facilities, the coal supplies which can be put through them, and the market prospects for the future. It assumes, rightly or wrongly, that there will be no major and prolonged disruptions in supply from any major sources of coal. COAL RESERVES FOR EXPORT Economically recoverable reserves in the non-communist world amount to about 470 billion tonnes. These are sufficient to sustain current production levels of 2 billion tonnes a year for 235 years.

Jan 1, 1984

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982

By SANDEEP KUMAR JENA

This paper reviews the recovery of potassium from different rocks and mineral sources. Global demand for potassium is rising steadily due to the growth of agricultural production. Fertilizer manufacture consumes the majority of the world’s potassium production, with other uses including those in the pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash (K2O) minerals, such as sylvite, kainite and carnalite, in countries like Canada, the United States, Israel and Russia makes them major potash producers, whereas agriculture-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia, Malaysia and India meet their potassium requirements through imports only. In these countries, the huge availability of potassium-bearing rocks/minerals like nepheline syenite, feldspar, mica and glauconitic sandstone, containing around 4 to 17 percent K2O, brings up the prospect of commercial production of potassium. Potassium recovery from minerals/rocks is complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast-leaching have been discussed for the successful recovery of potash values from these rocks/minerals. Although seawater is vastly available, the recovery of potassium from seawater using chemical precipitation, solvent extraction, membrane separation and ion-exchange methods is not cost-effective due to low concentration of potassium.

By P. S. Newall

As part of a much larger research project, factor analysis was employed to help interpret and compare the geochemical signatures produced by two different sample media; a traditional -80# soil fraction, and a coarse float. Both sample types were collected by hand auger from the extension zone of the Redmoor sheeted-vein complex and analyzed -for 19 major and trace elements. The rationale behind the study infers that the geochemical anomalies produced by wallrock alteration around such targets can be better detected in the lithogeochemical rather than the soil environment, sometimes at considerable distance from their source.

Jan 1, 1991

By E. W. Bauman

The important role that mineral aggregates assume today in the construction and chemical industries is best attested to by the astronomical tonnage figures for the annual production of aggregates in the United States as reported by the U. S. Bureau of Mines in their "Minerals Yearbook." For 1965, latest publication available, the tabulation shows a total of 1,716,000,000 tons made up of 30,000,000 slag, 908,000,000 sand and gravel, and 778,000,000 crushed stone. A much more favorable statistical position for slag can be established by listing the world-wide tonnage. According to Dr. A, W. Lee, Director, British Slag Federation, in a paper presented before the 8th Annual conference of the British Institute of Works and Highway Superintendents, he estimates that the probable world consumption of slag is in the order of 100,000,000 tons showing--Great Britain with 10,000,000 tons, Germany, 15,000,000 tons, France, 1$000,000 tons and the United States with 30,000,000 tons. Thus it is seen that the United States accounts for almost one-third of the world's consumption of slag and the 3 west European powers another third.

Jan 1, 1967

By William Bergeson

This paper presents the challenges of the Homestead Avenue Interceptor Extension (HAIE) project in downtown Hartford, Connecticut. The new 72-inch (1,830 mm) sewer pipeline project consists of installing approximately 3,010 linear feet (920 m) of PVC lined reinforced concrete pipe using pressurized face microtunneling. The entire alignment is located within soft to very soft, varved silt and clay. To the extent possible, the alignment was selected to avoid bedrock, glacial till, miscellaneous fill,buried steel piles, and utilities. Challenges for this project include low ground cover, crossing major transportation routes, and limiting settlement to prevent damage to historical buildings and critical utilities. The machine was selected for the ground conditions. Design calculations were performed for selecting the reinforced concrete pipe class and for evaluating settlement. The potential for settlement damage was evaluated using both conventional analysis and finite element analysis

By J. Iannicelli

Spray drying is the principal drying method used in the production of over six million tons annually of beneficiated kaolin in Georgia. Thirty-three dryers in the Georgia Kaolin belt comprise the highest concentration of large tonnage spray dryers in the world. The steady growth of spray drying in the U.S. kaolin industry is paced by advances in design and development of large spray dryers which have led to large scale new applications in mining and related industries.

Jan 1, 1982

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022