Search Documents

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By L. Cui

A new flotation collector, benzyl arsonic acid, was used for the flotation of ilmenite. ESCA, Auger spectroscopy, and chemical analysis were used to investigate the correlation between the variation in surface constituents and the flotation recovery of ilmenite. Experiments indicated that, as the ratio of surface Ti ions/surface Fe ions increases, flotation recovery increases. pH regulation with an inorganic acid was found to be effective in changing the ratio of surface ions, and, hence, the flotation recovery.

Jan 1, 1986

By Donna Wallace

Past EPA groundwater monitoring programs required that contamination not leave the boundaries of a disposal facility. New regulations under the Resource Conservation and Recovery Act (RCRA) require that once hazardous waste constituents are detected beyond the limits of the disposal area, a program to define the rate and extent of contaminant migration must be instituted. Future regulations are likely to include even more stringent groundwater protection criteria. The implications of both the existing and probable future groundwater protection and monitoring requirements in terms of using geologic containment as a means of disposing of hazardous waste are explored in this paper.

Jan 1, 1981

By Qiong Wu, Qinghua Gu, Yichuan Lv, Jin Yuan, Caiwu Lu

"The cut-off grade is one of the important parameters of mining production. Different material cut-off grade is directed to different destinations. Based on reasonable and optimal cut-off grade, long term mining plan and investment decision analysis can be made for mining managers. In view of multiple-metals open-pit, the paper has proposed that multiple-metals cut-off grade optimization model is set using the objective function to maximize net present value (NPV). The method of equivalent coefficient calculation is proposed to convert multi-metals cut-off grade optimization to a single metal cut-off grade optimization. Then the optimization model is applied in a molybdenum and tungsten large open-pit mine in china. The parameters of concentrate price are calculated by PRT in the model and the curve of grade-recovery rate is analyzed and studied according to actual production data. Based on 3D metal deposit model, the distribution of grade-tonnage is analyzed. At final step, an optimal cut-off grade is proposed to guarantee to maximize NPV. The example shows that the model of multiple-metals cut-off grade optimization can provide reasonable analysis for optimal multi-metals cut-off grade and develop optimal production strategies. Introduction Cut-off grade is one of the most important parameters in metal ore mining because of its influence on the overall economic profit of mining production. Along with the development of the mining production, dynamic optimization of cut-off grade is necessary through the analysis of technical economy. It is better to manage the mining production according to the variation of market. The cut-off grade plays an important role in mining production."

Jan 1, 2017

By R. W. Waytulonis

New exhaust control techniques and devices may be necessary to meet future diesel particulate matter emission standards in underground coal mines. This paper reviews conventional work practices and devices used to control diesel exhaust emissions, and new techniques being tested by the Bureau of Mines. Discussions will center on important work practices and on the function and efficiency of exhaust after-treatment devices. An industry/government cooperative research project to develop and test an exhaust after-treatment system for part 36 equipment is also discussed.

Jan 1, 1990

By S. D. Michaelson

Open pits and quarries are the major sources of all "hard rock" tonnage mined today. Normally, ore is fractured from the pit face by blasting and then truck-hauled to a primary crusher where processing begins; over- burden (or waste) is generally truck-hauled from the pit to dump areas. Truck haulage of blasted ore and overburden accounts for some 25 to 50 percent of total mining costs in a typical open pit and commonly is the largest single cost factor. Obviously then, cost reduction efforts should properly focus on improving existing haulage systems and developing new breakthrough techniques for material transport. Continuous flow systems for large tonnages ordinarily will result in a lower cost than batch systems such as truck or rail haulage. Continuous flow with pipelines for liquids and slurries, or conveyors for medium to coarse dry materials (in the -8 in. range) are the accepted economic answers for bulk materials handling over reasonable distances.

Jan 1, 1968

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By Madan M. Singh

Although roof bolting has been a major means of strata support for nearly two decades, little attention has been directed towards the design of bolt Installations. The variables involved are interdependent and their study complex. However, some simple tests may be employed to serve as guides to the efficient design of roof bolt systems. Local conditions are continually varying and are important to pattern design. This paper discusses such considerations and suggests techniques which may be employed to effect improved roof control with bolts.

Jan 1, 1967

By James M. Krese

The West Kentucky Division of Island Creek Coal Company, which is a wholly owned subsidiary of Occidental Petroleum Corporation, operates the new Hamilton Mine. It is located six miles West of Morganfield, Kentucky, in the Northwest section of Union County, adjacent to the Ohio River in Lock 50. On July 15, 1968, a unique new coal conveying system was put in operation. This system consists of eight conveyor units carrying coal from the bottom of the mine slope ultimately to barges on the Ohio River. It is over two miles in length and has a total of 3175 connected horsepower. The river loading conveyor is the longest 72" wide conveyor in operation in this country.

Jan 1, 1969

By Ron Robinson, Trevor Harrison

The planning, installation and commissioning of the first scheme of controlled recirculation of air flow in a section of coal mine in Great Britain is described, together with the proposals for a second installation. The work updates a previous paper (Robinson and Harrison, l986) on the subject. The special problems of ventilating the increasingly distant faces of the undersea mines in the North East Area of the British Coal Corporation are discussed and the alternative solutions stated. The advantages of using a system of controlled recirculation of air are proposed together with the safety features considered necessary. Design and installation details of the recirculation fans and a new booster fan are described.

Jan 1, 1987

By G. Pan

The production data of many mines have not reconciled geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metals are sometimes as large as 30%. A number of factors are responsible for such unpleasant outcomes. A major cause, however, is the lack of geological controls in the implementation of geostatistical techniques. Geological modeling establishes geological constraints and mineralization/ore envelopes. Geological constraints are usually established through drill hole interpretation. Mineralization and ore envelopes have been delineated manually based on assay grades. The issues associated with manual methods are: •Time requirements . •Inconsistent dilution. •Uncontrollable implementation variance. Although the time issue may not be a big concern for some companies, the other two have been responsible for many undesired estimation errors. A new geostatistical approach described in this study is designed on the basis of indicator and ordinary kriging. The central component of the method is the procedure for automatic delineation of mineralization and ore envelopes. The method, referred to as probability assigned constrained kriging (PACK), is demonstrated on a Carlin-type gold deposit. The estimation results are compared to blast-hole based production panels, showing that the estimated tonnage is about 2.1 % higher than the actual production, and the average grade is about 2.4% lower.

Jan 1, 1995

By R. W. Lake

The decision to develop an ore body can lead to multi-million dollar profits, or equally substantial losses. Accordingly, the effort required to adapt a valuation model to the specific proposal at hand, or even the development of a new model from basic principles, is clearly warranted. In the formulation of a model of this nature, one is faced with some major questions. For example, with the long term obligations that it implies, on what basis should a decision to initiate mining operations be made? Furthermore, how can the vagaries of inflation and the uncertainties that shroud the future be accommodated? Beyond the general principles by which mineral deposits are evaluated, specific cost behaviour is a function of the geology of the deposit, and of the mine design. Moreover, mine design, during the life of the mine, must be a continuing process somewhat akin to dynamic programming. An initial, apparently optimal, design is selected and mining commences. With production, a continual process of information updating leads to revisions. Thus if the maximum value is to be obtained, the mine design must be adjusted to conform to the changed conditions.

Jan 1, 1977

By Burke Trafton

An earlier paper1 introduced a rapid solution for mine ventilation network problems, employing the digital computer. In this paper, refinements and additions to the computer program which expand its scope of application and a solution to a ventilation network having a coal-mine configuration are presented. Specifically, the revised program--written in FORTRAN for the IBM 7074 computer in Penn State's Computation Center--is applicable to any mine ventilation network employing natural splitting and having its fan located externally. It accomplishes the following; 1. Distributes an assumed total quantity of air flow among all air- ways of the network, performing iterations until an acceptable level of error is attained and the flow in each airway is known. 2, Computes the pressure drop (head loss) in all airways and the overall network and mine head losses. 3. Determines the operating point for the mine and a given fan, adjusting all air flows and head losses to the actual values.

Jan 1, 1964

By Dan Nilsson

INTRODUCTION There are many mine planning factors in sublevel caving, as in the other mining systems, which when varied can substantially alter mining costs and profit¬ability. In this chapter, the following four topics are addressed with regard to economic optimization of sub¬level caving: production planning, haulage level spacing, orepass spacing, and extraction cutoff. The costs used here are the right order of magnitude but since each mine is unique, they should be considered only as examples. The objective is to demonstrate the tech¬niques which can be used. In a real mine, the evalua¬tions must be done using actual costs and conditions. It is difficult to predict exactly the costs involved, and therefore it is valuable to perform a sensitivity analysis to evaluate the effect of making incorrect as¬sumptions. Since the mining industry is very capital intensive, the effect of the interest rate must also be studied. PRODUCTION PLAN FOR AN IRON ORE DEPOSIT Introduction The first and most important thing to do before de¬signing an underground mine is to establish a long-range production plan. Such a plan is necessary for all eco¬nomic evaluations and should provide information about the lifetime of the mine, how much ore and waste must be handled per year, how much development per year is required, etc. An example is given in the following section. Problem In an iron ore mine sublevel caving is used. The iron content is 42%, and the mine supplies a pelletizing plant with an annual capacity of 3 million t/a. The ore body is shown in Fig. 1. The length of the ore body is 1000 m and the width is 100 m. Each slice is 10 m high, and there are 10 m be¬tween crosscuts, each of which has an area of 20 m2. The density of the ore is 3.5 t/m3. The spacing between rings is 2 m, and the extraction is 100%. The iron con¬tent is 66% in the pellets and 6% in the tailings. The problem is to develop a detailed production plan. A typical sublevel caving sequence is shown in Fig. 2. Solution Amount of ore per meter of crosscut: 20 X 3.5 = 70 t. Number of crosscuts per slice= 100. Length of crosscuts per slice: 100 X 100 = 10 000. Ore from crosscuts per slice = 10 000 m X 20 m2 X 3.5 = 700 000 t. Number of sublevel caving rounds per slice: 10 000/2 = 5000. Area for each blast in sublevel caving: 10 X 10 - 20 = 80 m2. Amount of ore per blast: 80 m2 X 6 m X 3.5 = 560 t. Extraction: 100% (see extraction curve Fig. 12). Loaded ore per blast: 75% or 420 t. Loaded waste per blast: 25% or 140 t. Total: 560 t. Total amount of rock from each blast in the sublevel caving: Ore: 560 t of which 2 X 70 = 140 t from develop¬ment work and 420 t from sublevel caving. Waste: 140 t. Total: 700 t. The ore needed per year is 3 X (66-6)/42-6 5 mil¬lion t. Necessary number of blasts per year= 5,000,000/ 560 = 8929. Distance to develop per year = 8929 blasts per year X 2 m per blast 17 858 m. Total amount/year: Ore from development work 17 858 m x 70 t/m = 1.25 million t/a Ore from sublevel caving: 8929 blasts per year X 420 tons per blast = 3.75 million t/a 5.00 million t/a Waste rock dilution: 8929 blasts per year X 140 tons per blast 1.25 million t/a Total amount to hoist 6.25 million t/ a The amount of ore from development work will in¬crease a little if the horizontal drift is placed in the ore body and not in the footwall. In this example the ore loss in 20%, and the waste rock dilution is also 20%. After taking the ore loss into account, the lifetime for 100 m of the ore body will be:

Jan 1, 1982

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By Norbert Patzelt, Johann Knecht

Future ore reserves of major gold producers in North America and elsewhere will consist of refractory gold ores. About 60 % of the current U.S. gold production is mined in Nevada. Several of the large gold operations in this state indicate that 40 to 90 % of their future ore feeds will contain refractory gold. To com­pound problems, average head grades for refractory U.S. gold ores had fallen from 8 - 9 g/mt to about 4 g/mt by 1991. In Latin America, 52 % of the gold operations will require milling for optimal recovery. Deeper reserves are, like in North America, refractory. Therefore a special treatment process is needed in order to allow for the gold ore to be leached downstream in a conven­tional cyanidation process for a high gold recovery. There are several options available for this oxidation process like treat­ment of the gold bearing ore in pressure oxidation, in a biooxi­dation or in a roasting plant depending on the reason for the refractoriness. If organic carbonaceous matters and sulfides are the prima­ry reasons for the refractoriness, whole ore roasting is a pre­ferred method for the treatment of this type of ore. Since dry ore is to feed to the roaster, a dry grinding mill is advantageous. For the dry grinding system, the moisture content and the ore char­acteristic is of importance. Those parameters decide the mode of the grinding system. For autoclave systems common wet grind­ing systems can be applied. This paper deals with technical aspects for dry grinding plants and gives an outlook on and pos­sibilities for new grinding systems.

Jan 1, 1996

By Jens Classen

"GENERAL PROJECT DATA The Sparvo Tunnel belongs to “Variante di Valico” project, a new 65 km highway link between Bologna and Florence, designed to renew the existing A1 route and to connect in a faster way Bologna and Flor-ence. It is composed of a 2,5 km twin tunnel excavated in a complex geological context, characterized by the presence of a series of surface landslides and methane gas. The gradient is 2.6 % and the minimum radius is 1’400 m. The internal diameter of the precast seg-ment lining, equivalent to the final section of the tunnel, is 13.6 m. MAIN TBM SPECIFICATIONS TBM Earth Pressure Balanced S-574 “Martina”, manufactured by Herrenknecht, has a theoretical excava-tion diameter of 15’615 mm. It is equipped with a conical shield 12.2 m long and four back-up gantries. The total length of the machine is approximately 130 m, weighing approximately 4’500 tons. The total installed power is 16’800 kW. The main drive has a diameter of 8’700 mm and has a triple axis roller type bearing equipped with a labyrinth system including 4 sealing lips. TIME SCHEDULE OF INITIAL TBM DRIVE A time schedule of the initial TBM drive is presented in the following list: •,August 25, 2011: start of the excavation of the 1st drive of the Sparvo tunnel •,October 29,2011: stop of the advance of the TBM for gear oil contamination and clogging •,October 29 to December 20, 2011: repair works on the main drive system and modifications on the conditioning system •,December 20,2011 to July 25, 2012: restart excavation of the 1st drive (north tunnel) and its breakthrough •,July 25 to November 29, 2012: 180° turning of the TBM, detailed check of the main drive seal-ing system and fixing problems on gear boxes, race ring, clamping ring and cutting wheel •,November 29,2012 to July 24, 2013: excavation of the 2nd drive (south tunnel) and its break-through •,August 2013 to July 31, 2014: disassembly of the TBM (first 4 months) and standstill of the jobsite for structural issues on precast concrete lining of the tunnel •,July 31, 2014 to March 10, 2015: inspection, dismantling and packaging of each part of the main drive (flange ring, gear box housing and main bearing). The various phases are described hereafter in detail."

Jan 1, 2016

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By J. Brune

The disaster at the Upper Big Branch (UBB) mine 2010 has demonstrated the destructive violence of a coal dust explosion by killing 29 miners in the worst mining accident the United States has experienced in almost 40 years. This explosion brought to light that the United States mining industry must strengthen explosion prevention and explosion hazard detection practices. Recent legislation such as the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) pushed the strengthening of explosion and disaster response and miner protection in addition to stricter regulations on the sealing of abandoned areas and on conveyor belt flame resistance. The focus of this new act was on how to respond to a disaster or explosion, yet not much improvement was made with respect to prevention explosion disasters. Researchers at the Colorado School of Mines have recently concluded extensive research into methane and coal dust explosion prevention practices and regulations as it may be applicable to underground mines in the United States. This research aims to forward more studies into the use and adoption of standards and procedures that have been utilized in countries with strong explosion prevention histories.

Feb 23, 2014

The Australian states of New South Wales (NSW) and Queensland, because of their endowment of black coal resources, dominate the production and export statistics for Australian coal. NSW produced 86 million tonnes of saleable coal in 1994, representing a doubling of output since 1980, or a growth of 5% per annum. Asian demand for thermal and coking coal has, of course, driven this growth in NSW. This high Asian demand is forecast to continue and NSW will seek to secure its share. This paper focuses on some of the issues facing NSW in the future, and in particular, examines some of the major new and proposed mining projects.

Jan 1, 1997