Search Documents

By J. L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak's potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1983

By Brad Simser

Several case histories from Glencore’s Sudbury Operations show how passive seismic monitoring data is used for geotechnical decision making. The data comes from three different seismic arrays monitoring two open stoping deposits, and a narrow vein cut and fill/blasthole operation. Mining depths range between 1000 to 1680m below surface. The deposits are hosted in hard igneous rocks typical of the Sudbury basin, with characteristically high horizontal stress (approximately 1.8 times the depth of overburden). Rockbursting is the main geotechnical risk, due to the strong brittle nature of the rock and local high mining extraction. Fault related seismicity includes both fault slip events, and the stress channelling effect as the mining front approaches a major fault structure. Planar data trends generally line up with known faults and often indicate early stage fault activation. The structures are risk ranked based on their seismic response. This has been particularly useful at the Nickel Rim South Mine (NRS) where the structural fabric (jointing and small-scale faulting) is generally parallel to the more through going faults. The persistence of structures is difficult to measure, and the NRS faults generally have low offsets and thin gouge. The visual difference between the more persistent structures that occasionally generate large seismic events (up Mw 2.9 to date) and localised joints/slips is often minor. The seismic monitoring data clearly shows the more active structures. This information is highlighted on mine plans to help guide enhanced ground support and seismic re-entry protocol barricade locations. Pillar loading/yielding is a key element to the blasthole operations where a primary/secondary mining sequence is used. The secondary pillars are mined in a yielded state with just-in-time development. An example of the seismic signature of a secondary stope is shown with emphasis on the need for high location accuracy given the stope widths of 12.5 to 15m. The ratio of the shear wave energy to primary wave energy (Es/Ep) has long been used as a method to estimate source mechanisms; the higher the ratio, the more likely the event is fault slip versus rock fracturing. Data sets are filtered on Es/Ep ratios to highlight both fault slip populations and stress fracturing mechanisms. Examples of seismic data quality checks, high stress development, and re-entry protocols are also shown in the case histories.

Apr 26, 2022

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) has been regulated by the U.S. Mine Safety and Health Administration since 2002 in underground metal and nonmetal mines. To demonstrate regulatory compliance, DPM samples must be collected and later analyzed by the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method, but the FLIR Airtec DPM monitor can serve as a complementary engineering tool. The monitor is a handheld instrument that offers near-real-time measurements of elemental carbon (EC), which is a primary constituent of DPM. As part of an ongoing field study, the monitor was used to survey EC in an underground stone mine. This effort was aimed at determining spatial and temporal DPM variations in several key locations. The results of prolonged area monitoring—that is, lasting several hours — revealed that DPM concentrations were diluted substantially as air moved away from the primary production zone, but that concentrations could vary quite a bit in a single location from day to day and between seasons. DPM concentrations were generally lower in winter than in summer, which is consistent with increased natural ventilation airflows during winter. Using a modified sampling cassette, an attempt was also made to sensitize the Airtec monitor to allow for “spot-checking” of EC concentrations — that is, measurements made in several minutes. Preliminary field data showed that the sensitive cassette performed well in terms of providing accurate data that could be useful for rapid assessment of DPM. IntroductionDiesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It largely consists of elemental carbon (EC) and organic carbon (OC) (Birch, 2003). The World Health Organization International Agency for Research on Cancer classified diesel exhaust, including DPM, as a carcinogen (World Health Organization, 2012). It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition and retention in lung tissue. Because DPM exists in both the micro- and nanoparticulate ranges, it can bypass typical autoimmune defense mechanisms that keep larger particles out of the respiratory system (Ristovski et al., 2012)."

Dec 1, 2016

By A. R. Rule

As part of the Federal effort to help maintain an adequate supply of fertilizer minerals, the Bureau of Mines is conducting research to characterize complex, low-grade western phosphate rock and to develop methods for economic recovery of phosphate. The rock varies from soft, friable, altered phosphatic shale to hard, tightly cemented, unaltered phosphate rock. To supplement current beneficiation by sizing, a flotation procedure was devised that included depression of phosphate minerals with H2SiF6 and anionic flotation of carbonate minerals, followed immediately by cationic flotation of silicate minerals. Application of the procedure to several different ores resulted in phosphate concentrates that ranged from 28 to 31 pct P20S in grade and from 60 to 70 pct in phosphate recovery.

Jan 1, 1977

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to-float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in the processing of porphyry ores and treatment methods to overcome the specific problems. Though some of the problems are interrelated the problems have been classified into three broad catagories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1984

By M. D. Monroe

Getting the best match between truck and haul road requires examination of many factors and their effect on the bottom line. Most mines use a bottom line measure based in some way on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. Productivity can be measured or predicted for specific tasks using either field measurement or modelling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture as they are time and task oriented and can be influenced by a summation of factors over a truck lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods of time. Other cost, such as fuel and tires can be tied more directly to certain tasks such as fuel and tire cost. This paper focuses on the more direct, task-oriented factors that affect truck productivity and cost.

Jan 1, 1992

By P. Bissert, M. Klein, L. Yan, D. Yantek

"Mine Safety and Health Administration (MSHA) regulations require underground coal mines to use refuge alternatives (RAs) to provide a breathable air environment for 96 hrs. One of the main concerns with the use of mobile RAs is the heat and humidity buildup inside an RA. The accumulation of heat and humidity can result in miners suffering heat stress or even death. MSHA regulations require that the apparent temperature in a fully occupied RA must not exceed 95°F. To investigate this issue, the National Institute for Occupational Safety and Health (NIOSH) conducted testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. The test results showed that the average measured air temperature within the RA increased by 9.4°C (17°F) and the relative humidity (RH) approached 94 %RH. The test results were used to benchmark a thermal simulation model of the tested RA. The validated thermal simulation model predicted the average air temperature inside the RA at the end of 96 hours to within 0.6°C (1.0°F) of the average measured air temperature. INTRODUCTION If an accident occurs in an underground coal mine, miners who fail to escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the potentially adverse thermal environment inside an RA from the metabolic heat of the occupants and the heat released by the carbon dioxide (CO2) scrubbing system. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The accumulation of heat and humidity can result in miners suffering heat stress, heat stroke, or even death. In its 2007 report to Congress, the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) recommended that RAs should be designed to ensure that the internal apparent temperature (a temperature-humidity metric) in an occupied RA does not exceed 35°C (95°F). However, a standard method to determine compliance with this metric does not exist. The heat transfer process within and surrounding an RA is very complex, and is not easily defined analytically or experimentally. To investigate the related issues, OMSHR conducted heat and humidity testing on a 23-person tent-type RA in its Experimental Mine (EM) in a test area that was isolated from the mine ventilation system. During the testing, numerous parameters were measured: heat input to the chamber, the air temperature and relative humidity inside the RA, the air temperature in the mine, the mine strata temperatures versus depth, and the airflow inside and outside the chamber. The focus of this paper is on the temperature rise within an RA. TAITherm heat transfer analysis software was used to develop a thermal simulation model of the RA as it was tested in the mine, using the test results as the benchmark. Both sensible and latent heat were used in the test and the model."

Jan 1, 2016

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in there two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section 1 of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the anti¬trust laws is entitled to recover treble damages plus costs.

Jan 1, 1966

By M. S. Klima

Coal gasification solid residue (slag) contains unconverted carbon (char), which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal-3.4 mm gasifier slag (-85% ash) to separate high (-100%) ash slag from low (-50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71 % was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1mm in size.

Jan 1, 1997

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were trans-mitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

Jan 1, 2004

By James S. Browning

In 1975 bituminous coal and lignite production in the United States reached an all-time high of 637 million tons, an increase of 6 percent over production in 1974. The output, valued at $11.9 billion f.o.b. mines, was produced at 5,100 mines in 24 states (6). Coal mining is the largest mining industry in Alabama. Production from Alabama's mines in 1975 was over 21 million tons, and present projections forecast a steady increase in production, with tonnages almost doubling by 1985 (5). Of the total quantity of coal produced, about 16 million tons were consumed in electric power generation and the remainder was used for metallurgical coke production, extraction of chemicals and petroleum based products, and power for industry. The fact that 75 percent of Alabama's power is generated by burning coal attests to the importance of this fossil fuel to the State. Approximately 14 million tons of coal were produced by strip-mining methods in Alabama during 1975 and about 7 million tons were produced by underground mining during the same period. Surface mining is expected to continue at about 14 million tons per year, but by 1980 underground coal mining is expected to increase to about 25 million tons (3). About 7 million tons of surface-mined coal in Alabama is subjected to some means of washing or cleaning. The methods used are screening accompanied by heavy media separation, jigging, tabling and flotation. Some of the simpler approaches employ screening and jigging, or tabling. Except where flotation is used, the screen undersize fraction (finer than 0.25 inch) is rejected, with the result that 10 to 15 percent of the coal is lost. Thus, in the State of Alabama an aggregate of about 1 million tons of coal is wasted annually in the fines which are impounded from treatment of surface-mined coal. The use of the Humphreys spiral to concentrate fine coal was practiced as early as 1947. At that time the Hudson Coal Company (1) used Humphreys spirals to concentrate anthracite fines. In 1950, the use of spirals to treat fine-size

Jan 1, 1977

By Alfredo Valdivia, Jesus Schabib, Vojtech Gall, William Cao, Curt Cicileo, Andrew J. Thompson

"The East Side Access Project (ESA) involves the construction of geometrically complex underground structures including a large number of caverns and bifurcations. Initially conceived as dual lined structures with either traditional concrete or shotcrete final linings (SFL), construction economy, advances in concrete placement technology and scheduling among others led to a wide use of what is referred to as freeform or pneumatically applied concrete (PAC) for the construction of tunnel final linings. PAC is a method of applying concrete without using formwork, where a wet mix concrete is pneumatically installed to encase reinforcement to full lining thickness. PAC has been widely adopted at ESA well beyond initial expectations. The paper addresses the design and construction aspects of the PAC method and contrasts it to traditional SFL lining placement. The experience made provides guidance for future PAC and SFL applications. THE EAST SIDE ACCESS PROJECT AND USE OF FREEFORM CONCRETE The Long Island Rail Road (LIRR) currently transports commuters from Long Island into Manhattan, terminating at the already congested Penn Station on the west side of Manhattan. Once completed, the ESA Project will provide LIRR commuters direct access to the east side of Manhattan underneath Grand Central Terminal. The ESA Project will help alleviate the congestion at Penn Station, which currently accommodates New Jersey Transit, Amtrak, and LIRR lines; reduce travel time for LIRR passengers traveling to the east side of Manhattan and facilitate connections to the New York City Transit (NYCT) Subway System and Metro North Rail Road. The construction includes mining and lining of new tunnels and facilities under Manhattan and Queens. The tunnels run from Queen’s Sunny Side Yard through the existing 63rd St. Tunnel, underneath Manhattan’s Park Avenue until termination at 37th Street. Differing types of tunneling methods and final lining systems are being used depending on the ground conditions, geometry and size of the excavation, site constraints and functional requirements. Mining of the Queens segment of the ESA Project involved soft ground tunneling by pressurized face tunnel boring machines, cut and cover construction, and conventional tunneling. The Manhattan segment of the ESA Project involves mining in hard rock by tunnel boring machines, drill and blast, and road header."

Jan 1, 2016

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By K. V. K. Prasad

Forecasting mined grade variability from exploration information is a challenging task in mine planning. For effective planning of activities such as workplace scheduling, ore grade quality control etc. development of realistic numerical/simulation models of in-situ variability from exploration information is an essential first step. Geostatistical conditional simulation (GCS) is one of the well known methods to develop these simulations. Recently, stochastic fractal models based on the assumptions of scale-in variance and self-similarity have been used for developing simulations of several natural phenomena. It has been suggested that these models might permit generation of short-scale variability information from exploration data with greater fidelity when the data satisfies the attendant assumptions. In this paper the stochastic fractal models are reviewed and their relationship to geostatistical variogram models is examined. A comparison of the two simulation techniques has been per-formed using coal sulfur data from a mined out coal property. The results of this comparative analysis are also presented in the paper.

Jan 1, 1992

By D. H. Steve Zou, Cui Lin

"This paper first discusses the basic attributes of sustainable mining and the responsibilities of various steak holders including mining companies, governments, and engineers. It is followed by a brief overview of the current practice on regulations, inspections, waste management and mine closure planning in Canadian mining industry. A case study is then presented as an example of sustainable mining where mine planning, mineral recovery, environment protection, reclamation and community development were integral parts of the overall strategy. A comparison of the mine site before and after mining is made to demonstrate the ""best practice"" in modern mining.Sustainability in Mineral Resource Development Extraction of mineral resources and other natural resources on the Earth has been and will continue to be an essential activity necessary to support human’s life. We live on the planet and depend on the available resources to survive. The extracted materials form the base to support modern life. However, we must be aware of the fact that mineral resources are limited on the Earth and may not last forever. Every time we extract one ton of materials, there is one ton less. They are not able to regenerate or regrow. One can ask a simple question: How long will they last? Or, is there anything left for our great grandchildren and many generations to come? The answer is not simple. Some minerals have become scarce or about to deplete. Some minerals may last longer. The reserve of a type of minerals depends on what we have discovered and the minable amount depends on accessibility and technology we have. Even if there are minerals in the deep ground, we may be limited by our technological capability. At the same time, we also need to understand the action of mineral extraction from the ground and the consequences of that action. Mineral extraction is a very hard work. We must break the ground to extract the ore, either through surface mining or underground mining. This action means disturbance of the land where we live. The disturbance is much more visible in surface mining than underground mining. The disturbed land, if not properly reclaimed after mining, is not going to be reusable. The very purpose of extracting minerals from the ground is to support our life but the action has a negative impact on our life. How can we reduce and limit disturbance of land from the action of minerals extraction? How can we make the disturbed land reusable? These issues must be properly addressed and a balance achieved."

Jan 1, 2017

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

New Mexico?s active coal mines have reclamation challenges that are being successfully resolved through the application of geomorphic grading methods. Soils and overburden material are often of poor quality, and annual precipitation is low. Revegetation on south and west aspect slopes often failed to persist. The New Mexico Mining and Minerals Division had therefore been encouraging topographic diversity on reclamation to improve water harvesting and reduce the percentage of south aspect slopes. Steeply dipping, multiple coal seams may be mined by open pit methods. Structurally-controlled trellis drainage patterns that exist premine have to be replaced with dendritic drainage patterns on reclamation where the overburden had been pulverized. Sodic spoil material is prone to differential settling and the creation of piping features in areas where runoff ponds, which may lead to downslope instability. In each of these scenarios, the approximation of natural drainage patterns on the reclamation has reduced erosion and sedimentation by creating shorter slopes with correct profiles, and by improving conditions for revegetation establishment.

Jan 1, 2010