Search Documents

By N. D. Policow, J. S. Orphanos

D.A. Dahlstrom In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in Fig. 4. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in Fig. 4. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensors, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89¢/t (81o; per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed. ? Reply by N.D. Policow From a technical standpoint, a number of extensive test programs have demonstrated that by raising the feed temperature, mechanical dewatering is enhanced whether it be centrifuges or filters performing the separation. Economic constraints usually become the over-riding issue. If an inexpensive source of thermal energy is available, i.e., waste steam, etc., the approach becomes commercially acceptable. For the specific case of coal slurry pipelines, since the dewatering plants will be located close to power generation stations, the preheating approach becomes especially attractive. The cost comparison shown in Fig. 7, which was prepared by a major West Coast engineering firm, contrasted screen bowl centrifuges and disc filters. In both alternatives, a thermal dryer was specified to produce a contract moisture of the final product. Sizing of the thermal dryer on the screen bowl alternative was substantially smaller than that of the filter, since the screen bowl was credited with a four to six percentage point decrease in product moisture compared to the disc. This comparison was made at ambient temperatures and reflected solely the mechanical dewatering capabilities of the two devices. No preheating of the feed was included in this particular comparison. Early generation screen bowl centrifuges operated under the principle of maximum bulk tonnage throughput. Second and third generation machines have followed the trends dictated by the coal industry calling for higher one-pass recoveries than previously demanded. The current generation of high-speed, long-bowl centrifuges permit recoveries of ultrafine solids directly comparable to commercial filter operation. On typical coal preparation plant feeds with nominal 600 E. an X 0 (28 mesh X 0) clean coal, recovery levels in excess of 99% are now obtained. The material that does escape the centrifuge and reports to the main effluent is typically -10 µm, high ash material. We have documented substantial beneficiation effects in screen bowl centrifuge performance with the cake product containing lower ash levels than the feed. On the referenced pipeline, coal tests performed on Western subbituminous coal, we found that the percentage of -10 µm material in the feed was six to eight times greater than normally encountered on eastern Appalachian seams. Our 45-t/h (50-stph) production centrifuge was never set up to maximize recovery. It was used as part of the two-stage dewatering circuit that had been chosen by designers of the proposed pipeline. Recoveries up to 95% were recorded. With field adjustments, that performance could most certainly have been improved. In contrast, manufacturers of the horizontal belt filter provided a small pilot-scale unit that operated on a side stream at the test facility. Numerous combinations of chemical additions were evaluated to determine those that had the best impact on filter performance. Whereas the screen bowl centrifuges operated without chemical addition, producing a dry, fluffy cake, the belt filter required two stages of chemical addition to attain satisfactory performance and high recovery levels. On the two-stage circuit that incorporated a belt press as the secondary

Jan 12, 1983

By Grant A. Brackebusch

Paste tailings disposal was successfully implemented at the New Jersey mill in Kellogg, ID with two different types of ore feed, a gold ore and a silver ore. The purpose of this paper is to describe the production of paste tailings, including operational problems during commissioning, and also highlight the environmental and economic benefits that were realized versus conventional tailings disposal such as the recycling of process water, increased shear strength and reduced permeability of the tailings mass, and reduced environmental permitting.

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be "land poor" but "coastline rich," meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. The Independent State of Papua New Guinea (the State) recognizes this tremendous opportunity and is taking a leadership role in this emerging industry by becoming a 15% partner in Solwara 1 (with an option to increase their investment to 30%).The Solwara 1 Project has been gaining momentum since Nautilus Minerals and the State signed an Agreement on April 24. This new agreement with the State in which they have staked a minimum 15% interest as a meaningful partner, underscores the State’s continued and widespread support for the Project. Signing of this Agreement was a historical occasion and a milestone achievement for Nautilus Minerals and the people of PNG.The machinery being built for the Solwara 1 Project is taking shape. The Seafloor Production Tools are now over 90 percent complete. Assembly of the biggest tool, the Bulk Cutter, was completed in April this year and assembly work on the Collecting Machine and the Auxiliary Cutter commenced in May and June this year respectively. The Riser and Lifting system, which will be used to transfer the mined material from the seafloor to the surface within an enclosed system, is over 50 percent complete. The critical path for the Solwara Project is to secure a suitable vessel arrangement. Nautilus aims to have this completed by the end of this year."

Sep 1, 2014

By A. Schaum

On average, there are approximately 10 fatal haul truck accidents per year. The most common causes for haul truck accidents include mechanical problems, inadequate training and insufficient road/berm maintenance. Due to the frequency and magnitude of haul truck accidents, new training methods are being investigated. With the widespread availability of computers and new technology becoming more reasonably priced, the ability to incorporate computer-based training for miners is becoming more possible. It has been shown that computer-based training is just as effective in knowledge acquisition as traditional lectures, and computer-based training can lead to a significant increase in the retention of material (Williams and Zahed, 1996). Studies have also shown that more engaging training methods lead to more effective knowledge acquisition (Burke et al., 2006). A supplemental system for current and new miner training to address the common causes of fatal accidents was developed. The training system is a virtual preshift inspection of a haul truck, and it can train new haul truck operators to identify parts that look defective. The training will increase an operator?s ability to recognize problematic parts and correctly identify the corrective action needed. Increasing the quality of training by providing an engaging, simulated hands-on environment will lead to safer behaviors by trainees, which will ultimately lead to fewer accidents and fatalities.

Jan 1, 2008

By Marcos de Paiva Bueno, Leonardo Ribeiro Lara, Rajiv Chandramohan, Thiago de Almeida, Greg Lane

This paper explores the impact of the significant difference between the number of geochemical assays conducted for grade estimation and the number of comminution tests performed for throughput and performance forecasting. Both grade and throughput are key factors in determining the project. We analysed 154 feasibility study reports to assess the impact of sample frequency for comminution test work on project revenue. This disparity in size between assay and comminution data arises because geological and resource-grade risks cannot be managed without extensive geochemical testing, whereas comminution risks are traditionally mitigated through design methods and the use of contingencies. This approach is partly due to the relatively high cost and large sample requirements associated with traditional comminution tests. Our analysis demonstrates that insufficient comminution sampling and testing leads to uncertainties in throughput forecasts, creating significant financial risks. Data from the feasibility studies show that a 1% change in mill throughput can result in up to a 5% variation in Net Present Value (NPV), underscoring the sensitivity of project economics to operational performance. Building on previous work, we reference studies that reveal how low frequency of comminution testing can increase uncertainty in mill throughput forecasts and increase financial risks. We propose an approach that optimises the number of comminution samples tested to enhance forecast accuracy and reduce NPV variance. By adopting this approach, mining projects can improve financial reliability and mitigate risks associated with underperformance in SAG and AG mill-based operations.

Feb 1, 2025

By C. O. Lee

The Grand Isle Sulphur Mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, Louisiana. The depth of water at this location is about 50 feet. The deposit is on acreage covered by oil, gas, and mineral leases which were originally issued in favor of Humble Oil & Refining Company by the State of Louisiana, and which were continued, maintained, and redesignated by the Department of the Interior of the United States, pursuant to Section 6(b) of the Outer Continental Shelf Lands Act. On September 19, 1956, Freeport Sulphur Company acquired from Humble Oil & Refining Company the sulphur rights underlying the tracts. This assignment was approved by the Secretary of the Interior on July 12, 1957. The Director, United States Geological Survey, approved Freeport Sulphur Company as Operator on July 31, 1957. Actual design began in September 1956; the first structural contract was let December 15, 1957, and offshore erection began in June 1958. The initial phase of construction will be completed and production started in early 1960. The estimated total cost of the project is $30,- 000,000, of which $8,000,000 is the extra cost for being in the Gulf of Mexico.

Jan 1, 1959

By Frederick C. Moore

This paper describes the original planning which actually resulted in the opening of a new aggregate plant located in central New York State. This plant, which is now named the Skaneateles Plant of The General Crushed Stone Company is unique in that the plant itself is a departure not only in design but in concept of operation from the normal aggregate plant the company has operated in the past. Whether or not the concepts which resulted in the Skaneateles Plant are economically feasible remain to be proven by the next few years of operation. By way of background data about our company which will help set the stage for this presentation, we currently operate seventeen stone quarries in the states of New York, Pennsylvania and Virginia. These quarries range in size from 200,000 tons per year to 1,500,000 tons per year with a total annual stone production of approximately 7,500,000 tons. We also produce about 1,250,000 tons of sand and gravel at six sand and gravel plants, 300,000 cubic yards of ready mix concrete, 1,500,000 tons of bituminous concrete, aglime and other minor construction materials. In many cases we are our own best customer consuming a large percentage of the total production of our own aggregates in our various ready mix and blacktop plants. Up to the concept of the Skaneateles Plant our operating facilities have been of the permanent type as opposed to the moveable or portable type plant. The steps involved in the case history of Skaneateles will begin with the basic economic requirements, market research, geologic surveys, land acquisition, zoning and financing and carry through to the final design and construction. We will attempt to show what some of the problems were, how we interpretted them and how we proceeded to solve them. The current results are apparent and can be analysed. The success of the total concepts of the Skaneateles Plant remains for future analysis.

Jan 1, 1968

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By Amir Karami, Scott Munro

This paper focuses on remediation of a 3.6 km long water conveyance tunnel that suffered two large falls of ground (FoGs), one of which subsequently progressed to the ground surface, resulting in full collapse of the tunnel. The tunnel is part of a network of water conveyance tunnels and open channels that direct water into two turbines located in an underground powerhouse, originally constructed in the 1970s. At the time of construction, the tunnel was partially supported with shotcrete or rock bolts, with no further ground support added since construction. Two sonar surveys in 019 and 01 identied two adacent large FoGs in the tunnel, approimately 1.2 km from the tunnel outlet. Historical geological and geotechnical information indicated that the FoGs occurred within a 60 m wide fault zone. Remediation plans were developed, which included stabilization of the outlet channel, the portal, the tunnel leading up to the FoG areas (1.2 km length) and the FoG areas. Several remediation options were considered to restore the tunnel, including construction of a diversion tunnel to bypass the FoGs or remediation of the FoG areas with steel ribs and backlling the void above the FoGs to surface.

Jun 23, 2024

By William C. Cooley

SUMMARY A review is presented of the state of development of high pressure water jet equipment and of large impact hammers for rock tunneling. Information from the U.S.S.R. is based on published literature and three personal visits. Applicable papers which were presented at the International Symposium on Jet Cutting Technology in Coventry, England in April 1972 are reviewed. Data are presented on continuous jet systems, pulsed water cannons, and hydraulic-powered impact hammers with respect to the specific energy of rock breakage and potential application in tunneling machines. INTRODUCTION It has been estimated that the cost of underground excavation during the period 1970-1979 in 15 countries of the Organization for Economic Cooperation and Development will be over $54 billion, an increase of 104% over the period 1960-1969. It is expected that 55% of the tunneling construction will occur in hard rock (Ref. 1). Present tunneling machines are generally limited to soft and medium-hard rock. When used in hard rock, the cost of replacing mechanical cutter bits is high. Therefore there is a need for improved rock fracture methods which can be applied economically in tunneling machines for hard rock. Water jets and mechanical hammers are two

Jan 1, 1997

By R. E. Moore

Refractories are unique ceramic materials, which are used in large quantities in steel making furnaces, metal smelting vessels, and glass melting tanks. They are required to possess high thermal shock properties and good slag corrosion resistance as well as creep resistance at high temperatures. Therefore, they are made from very refractory minerals such as lime, periclase, corundum, spinel, and zirconia. Slags are vitreous materials produced as a residue in steel refining processes. They cover a wide range of compositions and may contain pure oxides, silicates, and sulfides as well as fluoride phases depending on the melting and smelting processes. These minerals exhibit spectacular cathodoluminescence color under electron bombardment; therefore, cathodoluminescence (CL) microscopy is found to be a superior technique for the characterization of refractory corrosion by slags. Examples included in this study are (1) reaction of fluorine containing mold slags with ZrO2-C nozzle refractories promoting crystallization of the Cuspidine, Ca4Si2O7(F,OH)2, (2) corrosion of fusion cast refractories in TV panel glassmaking furnaces and formation of glass defects, and (3) reaction of spinel based castable refractories with copper smelting slags.

Jan 1, 2001

By J. `. Spitzinger

In situ recovery (ISR) of uranium alters the baseline groundwater geochemistry in order to mobilize and complex uranium to extract and concentrate it. ISR wellfield restoration is often challenging, and primarily relies on groundwater sweep, reinjection of treated permeate, and/or injection of reductants. Greater focus should be placed on injection-based approaches (using existing infrastructure) based on established engineering concepts used for in situ remediation of groundwater plumes. Such injection-based approaches could shorten restoration timeframes consequently reducing long-term operational costs. This paper addresses various types of injection-based approaches to wellfield restoration based on in-situ remediation success with other constituents that require similar treatment. This paper describes necessary design practices for injecting reactive chemicals (e.g., reductants or biostimulants), operations and maintenance (O&M) strategies to prevent fouling of the chemical delivery system and well network, and natural constraints to restoration. Best practices for successful biostimulation strategies that minimize residual uranium, radium, oxoanions, and other trace elements are as described. Advantages of such injection-based approaches could include significant reductions in restoration times, and consequently, lower restoration costs.

Feb 23, 2014

By H. L. Bourne

The sand dunes which line the east shore of Lake Michigan resulted after the last, or Wisconsin, glacial period in Michigan. Melt-water streams carried vast quantities of glacial debris to the near shore areas of predecessors to Lake Michigan. As the lake levels receded, these vast quantities of sand were exposed to the prevailing westerly winds, which was the last major process that acted upon the sand and resulted in the formation of the dunes. 1 These dunes are one of the significant natural resources within the state. Michigan dune sands supply about 90% of the foundry sand used in the automotive industry, and 40% of the foundry sand used 2 for all purposes within the United States. The deposits owe their importance to the following factors: grain size distribution, grain shape, mineral composition and location with respect to the foundry sand market. In spite of their economic significance these I deposits are in jeopardy through legislative preemption.

Jan 1, 1975

By T. Rasmussen, T. G. Jørgensen, T. Fischer, R. K. McLimans, C. Knudsen, D. Frei

Ilmenite-bearing paleo-beach deposits were discovered in Jylland, Denmark using a combination of Ground Penetrating Radar (GPR), portable X-ray fluorescence (XMET), bulk XRF analyses, Computer Controlled Scanning Electron Microscopy (CCSEM), and wire line logging. The Miocene-age paleo-beach deposits are located below a thin Quaternary cover in a region of very moderate relief and essentially no outcrop demanding unique approaches in exploration. Initially, an isopach map of the Quaternary is prepared from existing water well data. A geological model for likely occurrence of Miocene paleo-beach deposits is generated and the coincidence of thin Quaternary cover and potential paleo-beach deposits define targets for detailed exploration. The defined targets are traversed with GPR to identify paleo-beach structures which are then used to define a drilling program. This methodology located a paleo-barrier island at the Vorslunde location with more than 10% ilmenite in the sand. During the drilling process, the TiO2 and heavy mineral contents of the sand were logged every meter with a portable XRF unit (XMET) and subsequently calibrated more accurately by comparison to bulk XRF and CCSEM analyses for selected samples. The bulk XRF data also provided more complete compositional information. Insitu determination of geology, heavy mineral abundance, and corroboration of the XRF logging was done using wire line logs, a combination of spectral gamma and induction conductivity logs. Detailed characteristics (abundance, grain size, shape) and chemical composition of minerals was determined by the GEUS CCSEM methodology (Frei et al, this vol.). The average weight percent TiO2 for all Ti-minerals is 62%, 60% excluding rutile. That elevated TiO2 content (>> ilmenite stoichiometric value, ca. 50 %) indicates that ilmenite experienced an iron-leaching environment. The source of the sand deposit was investigated by dating contained zircon. The results show that the likely sources of zircon are in southern Norway and southwestern Sweden with common zircon ages of ca 1100 Ma. and 1500 Ma.

Jan 1, 2005

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012