Search Documents

By D. W. Mitchell

Never increase, reduce, or remove ventilation without unquestionable, compelling reasons. This rule applies every day as well as when fighting fire, attempting to find survivors, or recovering the mine. Right now in some mine a miner is adjusting a regulator in one place to get more air into another. The chances are the desired result will be achieved. Has the miner done a good thing? NO! Solving the immediate problem reinforces the belief he or she can do it again. That "again" might be, to give but one of many examples, the explosion in Greenwich No. 1 Mine. Robbing the proverbial Peter can be the prelude to disaster in a mine. Reducing the airflow is a common practice when fighting a mine fire. In fact, some people have been taught to do that at MSHA's academy. People who believe that to be proper must be people who never experienced a fire. To fight most fires you have to scramble to get enough air. An explosion demands totally different "thinking". If people are soon to go into the mine, DON'T adjust the ventilation. If teams are in the mine, each affected area must be explored or sealed before making any ventilation change.

Jan 1, 1993

By Issac Douglas, Sheila Devasahayam, John S. Thella, Manoj K. Mohanty, Jeremy Prishmont

The flotation performance of Sodium O, O-diisobutyl Di thiophosphate (referred to as reagent A) was compared with Aerophine 3418A (referred to as reagent B) for floating a complex copper ore grab sample (Ore A). Preliminary test results indicated a cumulative copper concentrate grade of 10.19% with a recovery of 86.31%, which was achieved with reagent A from a feed consisting of 5.32% Cu. The grade and recovery achieved using reagent B are 9.11% and 87.85%, respectively. A comparative analysis based on the preliminary test results indicated that reagent A’s performance is better than that of reagent B at lower concentrate grades, specifically below 12% Cu. However, the flotation performance is better for reagent B at higher concentrate grades (>12% Cu). A more detailed study was conducted to optimize the grade-recovery performances achievable from both reagents on a complex low-grade copper ore sample (Ore B) from Western USA. Test results indicated a copper concentrate with a grade of 5.5% Cu and 78.59% recovery was obtained with reagent A compared to 4.31% Cu and 62.04% recovery with reagent B from a feed consisting of around 0.25% Cu.

Feb 22, 2026

By A. D. Hammond

Vanadium is a transition metal, ductile, silver-gray metal. It is harder than most metals and steels and it has a good resistance to corrosion, it is stable against alkalis, sulfuric and hydrochloric acids. Vanadium is oxidized in air about 660 °C, although an oxide layer forms even at room temperature. The chemistry of vanadium is noteworthy for the accessibility of the four adjacent oxidation states 2-5. In aqueous solution the colors are lilac V2+, green V3+, blue VO2+ and, at high pH, yellow VO42-. Considered to be as abundant as zinc, metallic vanadium is not found in nature, but it is known to exist in about 65 different minerals. Economically significant examples include patronite (VS4), vanadinite (Pb5(VO4)3Cl), associated to the uranium mineral carnotite (K2(UO2)2(VO4)2?3H2O) and in a vanadium mica called, roscoelite K(V3+,Al,Mg)[(Si,Al)4O10](OH)2. Other important vanadium ore oxides are montroseite (V,Fe)O(OH) and corvusite (Na,Ca,K)V8O2.4H2O. Much of the world's vanadium mine production comes from magnetite-hosted deposit and to a lesser extent, in sedimentary-hosted sandstone. Vanadium is also present in bauxite and in fossil fuel deposits such as crude oil, coal, oil shale and tar sands. In crude oil, concentrations up to 1,200 ppm have been reported. A significant vanadium production comes from the processing of petroleum residues, fly ash and recycling spent catalysts. In 2011, metallurgical applications accounted for 93% of the use of vanadium. Here, an alloy called ferrovanadium is utilized to strengthen steel to be used as rebar in the construction industry, in the manufacturing of axles, crankshafts, gears and chassis in the automotive and transportation industries and in the manufacturing of high-speed tools. In the aerospace industry, vanadium is utilized as a titanium alloy in the manufacturing of airframes and jet engines. The reason for the wide use of vanadium as alloy is its high strength-to-weight ratio, the highest of any engineered material on earth. The major non-metallurgical use of vanadium is in the production of catalysts for the chemical industry. The most commercially important compound is vanadium pentoxide (V2O5), which is used as catalyst in the production of sulfuric acid.

Feb 23, 2014

Global mining company achieves significant productivity gains with three-dimensional (3D) mine models developed with Abaqus finite element analysis software. In a steep change beyond traditional processes, Abaqus finite element analysis (FEA) software from Simulia (the Dassault Systèmes? brand for realistic simulation), is being used to enhance mine design and engineering simulation at a number of major mines around the world. In North and South America, Africa and Australia some of the world?s biggest mining companies are applying FEA technology to evaluate safety and improve design planning, implementation and operations. Beck Arndt Engineering (BAE), a Sydney-based international consultancy, is a pioneer in the commercial development of engineering solutions for the mining industry. The consultancy has worked closely with engineers at Simulia Australia to expand the use of Abaqus FEA simulation software for mining applications. Among the early adoptors of mine-ready FEA technology is the world?s largest miner, BHP Billiton. With BAE?s help, BHP has already applied this technology to evaluate mines in Canada and Australia. At the BHP Billiton Nickel West Perserverance Deeps Project in Western Australia, Abaqus FEA software is now being used to help engineer the safety and productivity of planned deep-mining operations. To achieve this goal in the deep-mining environment significant technological innovation is required. Using measurements of site deformation and seismicity, Abaqus FEA models have been calibrated and, in a single day, used to simulate a full, 3D, inelastic analysis of a mine?s life cycle. In recent years, similar applications at Debswana?s Jwaneng Mine in Botswana, the Newcrest Mining Ridge-way Deeps Project in New South Wales, Australia and Rio Tinto?s Argyle Diamond mine in Western Australia have also established Abaqus FEA analysis as the lead-ing technology for multi scale, simulation-aided mining engineering. Joop Nagtegaal, a pioneer of FEA and a Dassault Systèmes Corporate Fellow, said that Abaqus FEA software is unique in its capabilities to enable mining engineers to investigate design innovations from the drawing board to full production. ?In the design stage, Abaqus models, which include rockmass volumes spanning several kilo-meters around the ore body and down to excavations just a few meters across, are used to compare and optimize engineering options,? Nagtegaal said. ?Then, as the mine goes into production, large volumes of data from the field are incorporated with the analysis models to allow them to be calibrated to a precision not previously available to the mining industry.?

Jan 1, 2009

By William H. Breeding

The remarks that follow are based substan¬tially on experience covering 45 years, 80% of which have been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more-difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1 ½ . The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present.

Jan 1, 1984

By M. Trim, Y. Sun, D. Tepavac, A. Kumar

Configuration of Rozelle Interchange Project’s ventilation system required design and construction of some of the largest and tallest underground civil caverns attempted in Australia. The paper focuses on the technical challenges of designing these caverns within a heterogeneous, generally weak sandstone under highstress conditions while providing a construction sequence that would align with the contractor’s preferred techniques and schedule. Various construction techniques were investigated, but ultimately an observational approach relying on a construction sequence and specialized instrumentation met both the designer’s and contractor’s requirements. Relevant data obtained from excavations and the construction monitoring program are presented within.

Dec 1, 2022

By SK SAHOO, UK SINGH, SK SHARMA, GSP SINGH

Surface mining accounts for most coal production in Indian geo-mining conditions compared with underground methods, whose implementations are in deeper coal reserves and for lower stripping ratio in a congested operating space. The bord-and-pillar method is the preferred underground method in India for reasons of flexibility and investment cost. While previous researchers conducted field investigations on intact overburden conditions, this study focuses on the strata control issues in a bord-and-pillar depillaring working under the influence of the dead-load condition of voluminous and fragmented softcover of overburden dump material. The modeling results helped in ascertaining the criticality of strata behavior and rib-pillar stability in actual mining conditions when compared with the conventional intact overburden.

By H. R. Hammond

The situation of The Consolidated Mining and Smelting Company of Canada Limited, or Cominco, may be somewhat unique in that the Company is not only a manufacturer of ammonium nitrate, but as a mining company is a major user of its own product. This situation has resulted in highly successful application of ammonium nitrate-oil explosives. Several noteworthy techniques have been developed and others have been improved. Use of this material in the mining industry has led ammonium nitrate producers to adopt the term nitro-carbo-nitrate or INN for ammonium nitrate-oil blends. A small blending plant at Cominco's largest mining property, the Sullivan Mine, at Kimberley, B.C., is producing more than 80% of all the explosive used at the Sullivan, and is supplying two other Cominco mines. Application has required intensive research to determine the best forms of ammonium nitrate for use in small holes drilled for development and long-hole stoping. It has led not only to experiments to determine the best blending oil, but also to development of loading techniques to the point where NCN is being moved through loading tubes over 700 feet. It has required research into mining practices such as hole arrangement and blasting of development cuts. It has resulted in the development of a special product for secondary breaking. All this has been accompanied by the recognition of the importance of insuring safe practices at every stage.

Jan 1, 1963

By Timothy P. Smirnoff, Anthony Stirbys, Amanda Elioff

The construction of the continuing expansion of the Los Angeles Metro System has required the construction of eight new station structures. One contractor proposed, as a construction alternative for the support of excavation of the Hollywood/Vine Station, the use of soil-mix walls instead of the conventional soldier piles and wood lagging. Soldier piles and shotcrete or wood lagging support systems had been generally used on the other sub-way station excavations constructed to date throughout the system. Immediately east of that station and in almost exactly the same geology, the Hollywood/Western Station was being excavated at the same time using a conventional support system. This paper com-pares the performance of these two support systems in the alluvial soils of the Los Angeles Basin.

Jan 1, 1997

By Jey K. Jeyapalan

A characteristic common to most tailings dam failures caused by earthquakes or excessive rain storm is that the tailings tend to liquefy and flow for substantial distances as a viscous fluid, with the potential for extensive damage to property and life. Failures of El Cobre, Chile (1965), Mochikoshi, Japan (1978), Aberfan, Wales (19661, Buffalo Creek, West Virginia (1972) are examples of such catastrophic incidents. In these four incidents more than 400 lives were lost, and the loss of property was approximately $200 million. In order to be able to assess the potential for damage in case of such a failure, it is necessary to predict the possible extent of flow slide movement. This paper discusses simple procedures for performing such analyses. Also, in order to illustrate the use of these analysis procedures in tailings dam design, two case histories are analyzed.

Jan 1, 1982

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

By K. S. E. Forssberg, J. A. Jirestig

Laboratory investigations on the possibility of using magnetic separation for the recovery of sulfide minerals have been reported. A survey of several sulfide ores and flotation concentrates indicated that, in most cases, magnetic separation is not a suitable primary beneficiation method. However, encouraging results have been obtained in concentrate purification. At the Boliden complex sulfide ore concentrator in Garpenberg, Sweden, an Allis-SALA Mark III carousel High Gradient Magnetic Separator (HGMS) is used with a small flotation circuit to recover sphalerite lost to the galena concentrate during lead flotation. After four years of refining the HGMS process, there has been an increase in zinc recovery and an enhancement in the quality of the lead concentrate.

Jan 1, 1994

By Barbara J. Arnold

A coal's size distribution, clay content and moisture content can affect its handling behavior, but the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.' s (formerly EPRI' S) Coal Quality Development Center (CQOC) and at Iowa State University (ISU) will answer these questions as part of a four-year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of various coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that, while moisture content-is the most important variable, the amount of -325M (-0.044 mm) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1990

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By Paul H. Muller

The configuration of remote seal DP cells for specific gravity measurement is described and the calculations for calibration are presented. The error induced by ambient temperature change is investigated as it relates to capillary dynamics and electronic considerations. Instrument specifications are discussed in the light of accuracy requirements and the calculation of error vs. ambient temperature is described.

Jan 1, 1984

By C. Sunderman, R. Jacksha

"Mine monitoring through various sensors is a vital component of successful miner safety and health programs. Data from environmental, geotechnical, infrastructure and other types of sensors are increasingly used to discover and mitigate health and safety concerns in underground mines. In many smaller underground mines, as well as in the new development headings of larger underground mines, leaky feeder communication systems may be the only available means to transport crucial monitoring data. In addition, data transport is increasingly being delivered using Internet Protocol (IP), while older forms of serial communication are being retired. This paper presents the selection, configuration and testing methodologies employed by researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) to integrate commercially available land mobile data radios into an existing leaky feeder communication system to provide IP data transport.IntroductionTo enhance the health and safety of their mining workforce, mine owners and operators are increasingly installing environmental monitoring and control systems in underground mines. Real-time, mine-wide monitoring is becoming a reality with the implementation of the Industrial Internet of Things (IIoT) into the underground mining industry (Zhou et al., 2017). However, not all underground mines, especially smaller mines and new development headings in larger mines, have the information technology infrastructure in place to handle the data transport requirements for the newer Internet Protocol (IP)-based technologies that are part of IIoT.This was the case with a mine in the Western United States. It lacked the infrastructure to perform critical monitoring in remote headings. Therefore, the mine partnered with the U.S. National Institute for Occupational Safety and Health’s (NIOSH) Spokane Mining Research Division (SMRD) to develop and evaluate a cost-effective solution for the real-time monitoring of geotechnical conditions in relatively remote sections of the mine. This paper describes SMRD’s solution to leverage the mine’s existing leaky feeder communications system to achieve IP data transport using commercially available land mobile data radios (NIOSH, 2013; Forooshani et al., 2013; Novak, Snyder and Kohler, 2010; Yarkan et al., 2009). The solution, fully evaluated in laboratory and mine environments, requires no modifications to the existing system, is economical, simple to implement, and reliable. It also allows for transition to higher-bandwidth IT networks, such as fiber optic or WiFi, should they become available."

Dec 1, 2018

By John W. Reddy

The C&NW Ore Dock at Escanaba, Michigan, is a major terminal on Lake Michigan for iron ore pellets arriving from the Marquette Iron Range located 112 km (70 miles) to the north. In an average year, the terminal handles in excess of 8 000 000 Mg (LT) of iron ore pellets consigned to a number of major steel companies. It is important to the steel companies for both cost control and operating efficiency that each cargo be sampled as accurately as possible in order to determine the physical and chemical properties of the pellets. This paper describes the equipment and operating procedures of the sampling facility and Presents some sampling data.

Jan 1, 1985

By Andrew B. Pervis

With the ever increasing demand for Finer powders by industry there has been a continuing effort by air classifier manufacturers to improve and offer machinery capable of producing these fine powders. Common to these classifiers is the use of a multivaned rotor through which passes all of the air used to transport the particles to be classified. Rotor revolutions per minute and the amount of air passing through the rotor are the main variables in determining the particle sizes which will be able to pass through the spinning rotor. A simplified equation derived by setting the air drag force carrying a particle through the rotor equal to the centrifugal force due to the spinning rotor's action on the entering air and particle is: Diameter of Particle = [ ] Where K is a function of air viscosity, particle configuration, rotor and blade configuration; RPM is rotor revolutions per minute; M3/sec. is air quantity passing through the openings between the rotor blades.

Jan 1, 1983

By Andrew B. Cecala, Robert J. Timko, Christopher J. Pritchard

As mine venti1ation systems become more complex, it is increasingly difficult to supply fresh air to the working face. A high percentage of the fresh air entering a mine never reaches the working face because it short circuits through stoppings and doors, exiting the mine without being utilized. When ventilation limits are reached, the only option presently available to most U.S. mines is to sink a new shaft - an extremely expensive undertaking that many companies cannot afford. Reusing or recirculating a percentage of ventilating airflow may make it possible for some mines to remain operational while maintaining a safe environment for workers. Such a study was performed at a trona mine in Granger. Wyoming. A vane axial fan was used to recirculate approximately 9.4 m /s (20,000 cfm), 25% of the total ventilating airflow, back to the working face area of a three-entry continuous miner section. This study involved two evaluations: the first when the face was 305m (1,000 ft) from the recirculation fan, the second when the face was 610m (2,000 ft) from the fan. The evaluation consisted of monitoring the mine atmosphere for respirable dust, methane (CH4). carbon monoxide (CO), and nitric oxide (NO), at various locations in the intake and return entries. Several shifts were monitored, with and without the recirculation system in operation. With the recirculation system in operation. there was an increase in measured respirable dust concentrations in the intake along with a slight increase in the mine temperature (1.67°C). There were also some minor changes in CO and NO levels in the intake entry, but this seemed to depend on the proximity of the instruments to the turn-around point for the diesel haulage vehicles, than to whether the recirculation system was or was not in use.

Jan 1, 1989

By Z. Y. Hu

This paper reviews the past and presents the present state of industrial minerals in China. The resources, reserve and production of major non-metallic minerals are given. The mining and milling operations are reviewed. The future development and plans of Chinese non-metallic minerals industry are summarized.

Jan 1, 1990