Search Documents

By Robert W. Curtis

Kaiser Aluminum & Chemical Corporation's (KACC) entrance into the alumina market began in 1946 with the purchase of a small plant in Baton Rouge. Louisiana. Since that time KACC has been involved with the design, construct; on, and operation of many alumina plants around the world. One of these plants is located in Gramercy, Louisiana. The Gramercy Works is a multiplant installation consisting of an alumina plant, a caustic-chlorine plant, a petroleum coke calciner and a fluorochemicals plant. Each of these plants require their own specific environmental control programs to abate pollution. Kaiser has made significant progress through the years on their own initiative in pollution control. But many new challenges have been and continue to be created with the enactment of environmental laws. The 1970 Clean Air Act Amendments, the resurrection of the old "Refuse Act" in 1970 and finally the 1972 Federal Water Pollution Control Act Amendments prompted the formulation of our current philosophy towards the abatement of pollution. Since the formulation of these complicated pieces of legislation, others equally complicated, have come to being. The Federal Insecticide, Fungicide and Rodenticide Act as amended by the Federal Environmental Pesticide Control Act of October, 1972, the Toxic Substances Control Act of 1976, the Solid Waste Disposal and Resource Recovery Act of 1976 and the Safe Drinking Water Act sighed in December of 1974 have all contributed to the challenge for an alumina plant to meet regulatory constraints. However, this paper will only discuss the alumina plant?s environmental programs designed to meet compliance with air and water pollution legislation. At the Gramercy Alumina Plant, over $25 million has been spent for pollution control since 1969. The Gramercy Plant is a prime example of KACC's commitment to meeting the environmental challenge.

Jan 1, 1978

By Kenneth R. Dickson, I. Michael Gowring

This paper describes the underground work associated with the North Fork Stanislaus River Hydroelectric Development currently being constructed by Sierra Constructors for the Calaveras County Water District in California under a turnkey contract. Sierra Constructors is a joint venture of the Guy F. Atkinson Construction Company (sponsor) of South San Francisco, and the Harrison Western Corporation of Denver. Notable features of this project include the exceptionally high performance achieved by the 5.5m diameter Robbins tunneling machine and the 675m deep shaft pilot hole which was successfully realigned using oilfield directional drilling techniques. Other features include 3.7m and 4.3m diameter machine-excavated tunnels and various conventionally excavated tunnels constructed over a wide geographical area and diverse climatic conditions.

Jan 1, 1987

By S. Odell

The Bureau of Land Management (BLM) has constructed two biochemical reactor systems (BCRs) to treat mining influenced water from the Forest Queen Mine near Silverton, CO. The bioreactors coupled with a natural wetland provide treatment to the Forest Queen Mine drainage. The central objective of this paper is to review the performance of the bioreactors and wetland treatment system. The bioreactors have been in operation for nine years and along with the natural wetland are still removing a high percentage of the influent metals.

Jan 1, 2010

By Frank A. Jerabek

Pneumatic stowing was first introduced in longwall mining in the middle twenties. Since that time it has advanced through many stages of development, particularly abroad, which have greatly improved its efficiency and contributed to its growing use. Pneumatic stowing originated in coal mining but has also been adopted in metal mining. This paper discusses the techniques of pneumatic conveying of. stowing material and equipment and applications of pneumatic stowing.

Jan 1, 1966

By Peter Werner

Technological advances in mine equipment and milling processes have enabled mining companies to exploit ever lower grades of ore. The result has been larger disturbances, greater volumes of waste, a complex web of infrastructure, and an overall trend toward mega projects that can extend over several square kilometers. This explosive growth in a mining operation’s disturbance footprint provokes an obvious question: What is it going to cost to reclaim all of this? At face value, this can be an enormous financial liability for a company, but since the timing of reclamation may be years in the future for many operations, these costs can be heavily discounted, thereby limiting the burden on the corporate balance sheet. Nonetheless, mining companies are eager to remove these liabilities as quickly as possible; conversely, regulators want assurance reclamation will, in fact, occur. How might one bridge these competing interests? Navigating the practical and financial requirements of a post-closure landscape requires foresight, judgement and assumptions; however, companies that do not adequately plan for these future expenditures when there is no offsetting income stream will likely face some difficult decisions. Simple risk analysis tools and utilizing the time value of money can help bring some clarity to this end-of-mine life phase.

Dec 1, 2025

By Horst Huettenhain

The Rowland Coal Preparation Plant is located on Workman's Creek in Raleigh County, West Virginia, approximately 20 miles Northwest of Beckley and 10 miles Southeast of Ameagle. It is owned and operated by the Rowland Division of Consolidation Coal Company. This paper describes the plant flowsheet, process considerations that were evaluated in its development, and observations made during and since the plant was constructed. The final flowsheet was developed specifically to wash the coal from the Rowland Mine and contains several equipment combinations and applications heretofore never placed in a single, commercial operation. The major process equipment is presented in a functional description of the flowsheet. The coal reserves are leased from the Rowland Land Company and consist primarily of #2 Gas and Middle Eagle coals and various major splits of the Middle Eagle seam. The Rowland Coal Preparation Plant was designed to process 560 TPH of raw coal consisting of 50 percent #2 Gas coal intimately mixed with 50 percent Middle Eagle coal and containing lumps no larger than a 12-inch cube.

Jan 1, 1970

By Peter Werner

Technological advances in mine equipment and milling processes have enabled mining companies to exploit ever lower grades of ore. The result has been larger disturbances, greater volumes of waste, a complex web of infrastructure, and an overall trend towards mega-projects that can extend over several square kilometers. This explosive growth in a mining operation’s disturbance footprint provokes an obvious question: What’s it going to cost to reclaim all of this? At face value, this can be an enormous financial liability for a company, but since the timing of reclamation may be years in the future for many operations, these costs can be heavily discounted thereby limiting the burden on the corporate balance sheet. Nonetheless, mining companies are eager to remove these liabilities as quickly as possible, conversely, regulators want assurance reclamation will, in fact, occur. How might one bridge these competing interests? Navigating the practical and financial requirements of a post-closure landscape requires foresight, judgement and assumptions, however, companies who do not adequately plan for these future expenditures when there is no off-setting income stream will likely face some difficult decisions. Simple risk analysis tools and utilizing the time value of money can help bring some clarity to this end-of-mine life phase.

Feb 1, 2025

By C. G. Anderson

The treatment of concentrates for the recovery of the precious metals imposes many processing and environmental challenges. Hydrometallurgical technology for recovery of values from refractory precious metal materials has been developed at Sunshine Mining and Refining Company. Historically, conventional pyrometallurgical methods have been used for to recover values from refractory precious metal materials. However, enhanced environmental awareness has worked to constrain typical refractory material processing methods. This hinders and limits the ability of established smelting or roasting technologies to fill the needs of new sources of refractory materials. An alternative is to treat refractory precious metal bearing materials by hydro metallurgical techniques. These methods are considered more environmentally appropriate since they do not produce gaseous pollutants like sulfur dioxide. Industrially, Sunshine Mining and Refining Company employs hydrometallurgical technology to process refractory precious metal materials. The Sunshine antimony leach uses a mixture of sulfur and caustic under ambient pressure and boiling conditions. The Sunshine oxidation leach uses a mixture of sulfuric acid and a minimal amount of sodium nitrite under relatively mild oxygen pressure and temperature conditions. These conditions result in a nitrogen species catalyzed sulfuric acid pressure leach. Since hydrometallurgical technologies provide industrially proven processing options for many types of refractory precious metal containing materials, their usage should be considered. Ample work has been conducted to prove the effectiveness of Sunshine refractory processing technologies on various materials. This has included platinum group metal materials, refractory gold concentrates, silver materials and indium materials. In some cases, complete process flowsheets have been designed to recover both base and precious metals from these materials and to treat the generated waste streams in environmentally sound manners.

Jan 1, 1996

By D. W. Hutchinson

One of the most important problems facing the coal industry today is the disposal of refuse from the coal preparation plants in a safe, economical, and efficient manner while complying with all legal requirements. The most commonly used refuse disposal method has been landfill/impoundment. In this method, the coarser refuse fractions are disposed of by layering and compaction into a landfill. The fine coal slurry refuse fraction is impounded in a dam constructed of a portion or all of the coarser refuse fractions. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the preparation, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. At the time of the promulgation of the new Federal regulations, United States Steel Corporation was in the process of designing the Cumberland preparation plant. As a result of the new regulations

Jan 1, 1977

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

By Feida Wu, Yuhang Liu, Huimin Gao, Yuhan Song, Zhi Liu, Zijie Ren

In the process of quartz purification by calcination water quenching, the different expansion rates of gangue minerals and quartz were used to produce cracks or remove fluid inclusions, which is conducive to subsequent purification. However, the role and mechanism of calcination-water quenching are still lacking in research. In this paper, the position of calcinationwater quenching in gangue quartz purification process was adjusted and the removal effect of calcination-water quenching process at different nodes in the process was explored. The results show that the purification effects of grinding-calcinationwater quenching-classification-acid leaching process and grinding-classification-acid leaching-calcination-water quenching process were relatively good. The main reason is that calcined water quenching can make quartz produce cracks, which are more rough. At the same time, calcined water quenching is located after grinding, which has a larger specific surface area, pore volume and pore diameter, and has a strong adsorption capacity for acid solutions.

Nov 2, 2023

By James A. Doolittle

In the underground type of mining operation, the finer portion of the waste material commonly is pumped as a hydraulic slurry to a tailings disposal pond. (1)* The tailings slurry is deposited via a pipe manifold system located around the perimeter of the pond. This method of deposition produces zoning because the coarser material tends to settle out immediately while the finer particles tend to remain in suspension and are deposited progressively nearer the center of the pond. The manifold system must be raised periodically as the pond fills with the tailings material. Over a period of time, this procedure will produce a zoned embankment known as a tailings dam. A typical pond and dam are shown in Figure 1. In plan view, the dimensions of tailings dams can be on the order of miles, with the height of the dam reaching 100 to 200 feet. Due to such factors as inadequate compaction, inherently low strength of the tailings material, and the possibility of high phreatic surface, many dams at some point become unstable, i.e., the factor of safety against a slope failure approaches 1.0. Remedial measures are required to improve the safety factor in order to prevent massive failure of the dam. In most cases, stability can be improved by effectively flattening the slope of the dam as shown in Figure 2, but this is not possible in every case. Occasionally, a tailings dam is constructed adjacent to a natural or legal boundary so that it is not possible to construct a conventional berm or to reduce the slope angle with earth moving equipment. Even a terracing process would require removal of the material and this may not be practical. In such a situation, an alternate scheme to improve stability must be found.

Jan 1, 1974

By David M. Stearns

Introduction Millions of tons of coal are shipped by rail each year in the US. Loading those trains efficiently is a topic being studied by coal producers and railroads. Alternatives range from volumetric loadouts to systems that weigh the product, using either belt conveyor scales, track scales, or weighbins. Each system has its proper application and each has pros and cons, depending on the volume, nature, and layout of the specific loading facility. In recent years, a batch weighing system has been developed that offers significant benefits to higher volume operations shipping by a unit train. The Unitrain Loadout System (ULS) features a precision electronic batch weighing system married to a mechanical loadout system by a microprocessor-based digital control system. A batch weighing loadout could be designed using analog electronics or even a mechanical weighbin. But it is the adaption and use of a microprocessor that provides the primary benefits of a unit train loading facility. Those benefits are accurate weight determination, optimum car use, overload prevention, speed in loading, optimum labor use, and documentation of the loading process. Unitrain History The first ULS was erected for iron ore applications in Canada during the 1960s. The first domestic system on coal was installed at Pittsburg and Midway Coal Co.'s McKinley mine at Gallup, NM, in 1978. At present, there are more than 20 Unitrain Loadout Systems in operation worldwide. They are loading minerals, concentrates, and coal. Eleven systems are presently in service or under construction in the US. In the last several years, a number of comparable systems have also been installed. As a result, the concept has been well proven and is now commercially available from several sources. Unitrain Operation The basic operation of a ULS involves loading a unit train with individually weighed batches of coal while it moves slowly under a loadout tower. Typical coal systems are designed to load at rates of 2.7 to 6.3 kt/h (3000 to 7000 stph). The contents of each car can be accurately weighed. This meets the requirements of the National Bureau of Standards Handbook No. 44 for static weighing. Also, cars can be loaded within very close tolerances. This optimizes railcar usage and prevents overloads. Principal components of the loadout system are the main feed conveyor, the surge bin, surge bin gates, weighbin, weighbin gate, flood loading chute, control room, calibration weights, and hydraulic and electrical systems (Fig. 1). Main feed conveyor: Coal is delivered from a storage area by the main feed conveyor. The conveyor fills the surge bin. It should be capable of conveying coal at the same rate at which it is being loaded. Usually the feed conveyor is equipped with a conveyor scale that can display rate in the control room and control feed to the belt. The surge bin will typically store 227 to 272 t (250 to 300 st) of coal. If the loadout is installed in an over-the-track silo, there is no need for a surge bin. Four double-bladed, hydraulically actuated gates are incorporated into the bottom of the surge bin. These gates open to fill the weighbin. Automatic pre-act points are selected by the control system. They shut these gates as the desired weight is approached. The final amount of coal is added by a single gate that closes. This results in a weighed batch of coal within ± 0.5% of the selected optimum load per railcar. Thus, if loading 91-t (100-st) capacity cars, the system is set to batch up 90.2 t (99.5 st) batches. Each car is expected to be loaded between 90 and 91 t (99 and 100 st). Weighbin: The weighbin is next in the flow scheme. Typically, it is

Jan 3, 1985

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By L. D. Hartzog

A pilot plant investigation of a semi-autogenous mill - ball mill circuit is described. The plant was operated with minus eight-inch diabase as feed material to the semi-autogenous mill. The semi-autogenous mill recycle screen underflow was put to a ball mill in closed circuit with a cyclone. An operating Work Index of 13.3 to 14.9 was obtained with the pilot ball mill. This Index is substantially in agreement with the scalped feed laboratory Work Index for 15.3 for recycle screen underflow. The Bond Index of the diabase was 15.8. Thus, one may use the scalped feed laboratory Work Index to size semi-autogenous grinding plant ball mills.

Jan 1, 1974

By M. K. Boateng, K. Awuah-Offei

"Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. The results show that the model is much more sensitive to the probability of imitation than the other two parameters. Thus, to reduce uncertainty surrounding the model’s predictions of community acceptance of mining, mines need to obtain accurate estimates of the probability of imitation. INTRODUCTION Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. AGENT-BASED MODEL OF COMMUNITY ACCEPTANCE A few researchers have started using agent-based models to study mining systems (Fujiono 2011; Nakagawa et al. 2013; Bahr 2015; Boateng and Awuah-Offei 2017a, b). Nakagawa and co-workers used ABM to evaluate dynamics of a mining project’s stakeholder networks whereas Fujiono used ABM to study innovation diffusion in the mining industry. Our previous work has presented models and a framework for modeling information diffusion in a mining community and its impact on level of acceptance (a measure of SLO) of the mining project (Boateng and Awuah-Offei 2017a, b)."

Jan 1, 2018

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010

By E. Craig Simmons

Uranium is an element incompatible with respect to the major rock-forming minerals crystallizing from granitic magma, entering in- stead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late- stage fluids which can form ore deposits directly, or labile U which can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U- enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks which are most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite Mine area, Washington, have geochemical characteristics which fit very well the model presented here. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1981

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;' eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By Jozef Stachulak

Prof. H. Bystron: "An Application of the First Law of Thermodynamics to Winter Dry Air Flow in Mr. Stachulak's Mine Model". [ ]

Jan 1, 1980