Search Documents

By Paul Taurasi, Mahmood Khwaja, Anjuli Corcovelos, William Brick

California’s San Diego County Water Authority provides a safe and reliable water supply to more than 3.3 million residents through twenty-four member agencies. The 2nd Aqueduct pipelines, a critical infrastructure consisting of three large-diameter pipelines, are susceptible to natural threats including streambed erosion, channel migration, and seismic hazards within the 3,840-foot-long Moosa Canyon segment of the alignment. A state-of-good repair, hazard mitigation, and resiliency project is progressing to ensure uninterrupted water supply. For each pipeline, a segment will be replaced by tunneling. A high-level project development approach is presented, focusing on alternative selection, environmental and geotechnical considerations, and operations and maintenance constraints.

Jun 13, 2023

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By F. S. Knoll

The high tension process which separates materials based on relative differences in surface conductivity has been very successful in recovering non-ferrous metals from municipal waste. Aluminum is by far the largest constitutent of the total non-ferrous metal fraction; accounting for >95% in most localities. Wire and insulation mixtures from industrial wastes have been treated commercially for several years by a high tension process initially developed for use in the iron ore industry. The wire and insulation application was a forerunner of municipal waste dry treatment technology. In the past eighteen months the rotating-drum-type electrostatic separator has undergone extensive testing and development in order that the process might be efficiently adapted to the recovery of aluminum from municipal waste.

Jan 1, 1974

By K. Verghese

Neutron capture prompt gamma-ray analysis provides the best method for on-line analysis of the elemental composition of large volumes of bulk material. This paper summarizes the Monte Carlo models which simulate the radiation transport within two such analyzer systems; namely, the borehole configuration and the conveyor belt configuration. The models are useful in the design optimization of the analyzer systems, in minimizing the amount of experimental calibration data for calibrating these analyzers, and in investigating the detection sensitivity for different elements. The computational scheme in these models is made extremely efficient by the use of various powerful variance reduction methods and by efficient data management. Experimental verifications of the two models carried out in the laboratory indicate very good agreement with the Monte Carlo results.

Jan 1, 1984

By Jacques Bernazeaud

Rouez is a recent discovery of a major low-grade sulfide body (± 100 m, 0,6 % Cu, 0.3 % Pb, 1 ,5 % Zn, 21 g/t Ag, 1.5 g/t Au) in a populated farming area of Brittany, France, some 30 kilometres northwest of Le Mans. The discovery is the result of an airborne electro- magnetic (INPUT) survey. It is the first time that the INPUT method has been used in France. The survey Gas successful in spite of the numerous interferences normally found in populated areas. The lack of a good drainage system would not allow the discovery of Rouez using stream sediment geochemistry alone. Ground geophysical surveys confirmed the airborne work and gave sufficient information to make the first hole a discovery hole. The deposit is Proterozoic in age and sediment-hosted. The metamorphism is low grade.

Jan 1, 1983

By Thomas E. Shufflebarger

Definition of glass sand prospects may be modified by constraints which range from demography to critically important product-control. Characteristics of usable raw materials, physical and chemical, are discussed; an ideal raw material is defined. Following field investigations and preliminary sampling, evaluation of selected prospects includes use of modern drilling techniques, viz.: core, percussion (air-hammer), auger, jet, rotary jet, split-spoon and other. Nearly complete core (sample) return is mandatory. Land-use regulations, availability of water and transportation continue to direct exploration in a major sense. But fitting a prospect to burdensome politics nay be considered a decidedly negative factor.

Jan 1, 1983

By Rudecindo S. Silo

[The principal characteristics of the process is that when applied in medium or in great degree it only needs unelaborated raw materials such as sodium chloride and calcium carbonate, or of medium elaboration, as sulphur which is found in large quantity in the North of Chili; however, the may be also applied to small copper plants provided that low cost sulphuric acid is available as a substitute for sulphur, that is, in. those plats of small capacity where large additional installations are not needed for the regeneration of the leaching solution. The method itself comprises 6 stages, namely: crushing, leaching, washing; of solutions, precipitation, regeneration of the leaching solution and fusion.]

Jan 1, 1965

By K. Hanna

Early identification of adverse geologic conditions and high stress concentrations during the high-speed extraction of coal using modern mechanized long wall systems is a major challenge facing the mining industry. Often, unexpected geologic anomalies that affect rock mass quality are encountered more rapidly, leaving the mine operator with insufficient time or information to deal with the changing ground conditions. The RockVision3DTM seismic tomographic system, developed by NSA Engineering, Inc., offers substantial benefits over conventional geologic/stress-detection methods and has been used successfully in coal mines worldwide. Tomographic images, produced economically and in near-real time, are easy to interpret, allowing mine operators to deal with potential hazards on a day-to-day basis. This paper focuses on the application of RockVision3DTM technology for delineating hazards caused by stress and geologic anomalies. Case studies for two bump-prone coal mines will be discussed. For example, (1) in a German deep (>1,130 m) mine, the drilling-yield method was used to verify the effectiveness of this technology in detecting stress anomalies ahead of longwalling; (2) in a Polish mine (-500 m deep), two longwall panels 4 km apart were monitored to assess structural and stress-related factors contributing to differences in mining conditions and magnitude of structural failures.

Jan 1, 1999

By T. L. Carstensen

The Miami In-situ mine of BHP Copper is located in Globe-Miami, Arizona. The mine leaches mineralized leach capping over a supergene enriched sulfide deposit, and has produced over 500 million lbs of copper during the last 50 years. The Miami unit has identified several opportunities to enhance and expand in-situ production. A computer block model consisting of strict geologic controls, mineralogy, and metallurgical data was developed to assist in the determination of the leachable copper resource. An understanding of the accessibility and solubility of the resource to leaching solutions and the integration of hydrogeologic and hydrometallurgical information was necessary for completion of this project.

Jan 1, 1997

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By T. M. Gurr

In response to concerns voiced by local, state, and federal agencies and various environmental groups, the Central Florida Phosphate Industry and various governmental agencies have been investigating methods to accelerate the consolidation of waste clays generated during phosphate washing and beneficiation processes. The objectives of research efforts have been to reduce the storage volumes required for clay waste, accelerate reclamation and to return the land to approximate pre-mining topography. Government and industry research to accelerate waste clay consolidation has evolved two general methods: gravity thickening and chemical flocculation. Gardinier, Inc. one of the phosphate mining companies, evaluated the use of synthetic (polyacrylamide) flocculants as an alternate waste clay thickening method in response to mining conditions encountered at their Fort Meade Mine and the proposed North Hardee County extension of the Fort Meade mine (Figure 1). After considerable research and evaluation, the Alsthom-Atlantic Clariflux Super-flocculation method was chosen by Gardinier, Inc. as a method to seriously consider for use at their Fort Meade mine.

Jan 1, 1986

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

A conventional paddle-type mixer and a gravity flow mixing device were evaluated for conditioning of phosphate ore with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity flow mixing required less residence-time, but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity flow mixer. For acid scrubbing, the gravity flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices will be discussed.

Jan 1, 1987

By Leons Kovisars

Two-thirds of the world copper produced in 1979 incurred cash costs between $0.35 and $0.89 per lb, averaging $0.62 per lb. North American costs are higher at $0.48, $0.88, and $0.68 per lb, respectively. Variable cash costs are $0.20, $0.58, and $0.39 per lb for the world; $0.29, $0.63, and $0.46 per lb for North America. Cash costs are relevant for comparing existing operations and evaluating market pricing during periods of excess supply. Analysis of full costs of production (cash costs plus income taxes, profit, and non-cash items) becomes relevant in evaluating the incentive price required to develop new production plants. In mid-1979 this cost (incentive price) was about $1.10 per lb; it is expected to approach $2.00 per lb by 1985.

Jan 1, 1979

By M. C. Rockwell, G. F. T. Lay

Promising placer gold exploration sites offshore Lunenburg County are drowned pre- and post-glacial river channels and auriferous glacial tills. Gold values up to 5.67 9/m3 have been encountered in the vicinity of the Ovens Peninsula offshore Lunenburg County. Moderate gold values associated with notable amounts of heavy minerals were reported from various other exploration sites in this area. This paper highlights the major geological and gemorphological features for placer gold depositions in southern Nova Scotia. The past to present gold exploration activities nearshore and offshore Lunenburg County are summarized and potential areas for placer gold identified.

Jan 1, 1988

By J. A. Ehler

Speed and torque control of standard A.C. induction motors can be accomplished using a variety of devices ranging from mechanical, hydraulic, and electrical. Also, the motor can be specified as an A.C. wound rotor or D.C. motor using the associated controls. Normally, any one of these drive types can be adequately used to provide the torque control necessary to accelerate a conveyor belt system. The selection will depend on the economics, experience, and preference of the designer or end user. These drive types will be presented from a functional and performance viewpoint to assist in the understanding of the available technology.

Jan 1, 1998

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By Daniel E. Collins

Massive banded Fe-Zn-Cu-Pb sulfide deposits in the Bagdad are associated with metamorphosed eugeosynclinal mafic volcanic and intrusives rocks Precambrian age. The geologic environment is very similar to that of the Jerome-Prescott area which lies 70 km. east of Bagdad. Mining of massive sulfides deposits began in 1917 on the Copper King mine in spite of its early discovery and the discovery of the Old Dick mine in 1882. The first shipments of zinc ore from the Copper King were hand sorted and averaged 46.89% Zn, 5.7 oz. Ag, 3.58% Pb and 1.68% Cu. Oxidized copper was first produced from the Old Dick mine in 1943~ In all, five deposits of massive sulfide ores have been mined in the Bagdad for a total production of nearly 2 million tons with an average grade of 12.0% Zn and 3.6% Cu. The largest deposit, the Bruce mine is currently closed because reduced metal prices and has produced a total of 823,000 tons of Zn-Cu ore to date. Mining of massive sulfide ore in the Bagdad area is presently idle. However, the potential for locating yet undiscovered ore bodies is good. Exploration for new ore bodies is difficult at best due to the complex geologic history of the area, the small size of individual ore bodies and lack of understanding as to the formation of massive sulfide deposits. The purpose of this investigation was to obtain a better understanding of the host rock formations through detailed geologic mapping, petrography and chemical analysis.

Jan 1, 1977

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. It is also a major exporter of minerals. Canadian open pits are highly mechanized and use state of the art equipment and support technology. During the past few years significant productivity improvements have been achieved by taking advantage of larger equipment; in pit crushing and conveying; truck dispatch systems and electronic management tools. The most recent developments in Canadian Open-pit Mining are related to hydraulic transportation and the application of Global Positioning Systems. Mine planning is computerized; environmental issues are dealt with in all phases of planning; equipment modifications are pursued with vigor to keep them functioning in the hostile Canadian North.

Jan 1, 1999

By J. E. Russell

The purpose of this paper is to describe an independent study which forecasts Texas coal production, specifically for electric power generation. This study, extending to the year 2000, is justified on the following basis. Texas produces and consumes considerably more electric energy than any other state, has consistently high growth rates in the population and industrial sectors, and has large lignite reserves. Also, since recent forecasts have been criticized as overly optimistic, this study is timely when considering the long lead times required in obtaining new power sources. In the study demand for electric energy was assumed to rest on two dominant factors: 1) overall state of the Texas economy as measured by the Texas Gross State Product (TGSP) and 2) Texas population. Demand models were prepared and tested following a study of several options. A final linear regression demand model with time lags for the two variables was chosen on the basis of good correlations. On the supply side, uncertainties such as impact of nuclear sources, gas-fired cogeneration, and ratio of imported to lignite coal exist. These uncertainties were studied with high and low cases for effects on lignite. Finally a simple supply model was chosen. Results of the study indicate that lignite production in Texas will rise from the current (1984) 40 million tons per year (XTPY) to the range of 77 to 124 MTPY and more probably 100 HTPY in the year 2000.

Jan 1, 1984