Search Documents

By Joseph E. Schiller

As part of the Bureau of Mines research on identification of asbestos fibers, a method was discovered for removing asbestos fibers from water. This report describes this process and its theory of operation. The surface charge of amphibole minerals in potable water was found to be negative, and in common with most other silicate minerals, the isoelectric point of amphibole asbestos fibers lies in the pH range 4 to 6. Magnesia is one of the rare oxides with a high isoelectric point of about 11. The surface of magnesium oxide will, therefore, be positively charged in water at pH 6 to 6, while the electric charge an. amphibole asbestos fibers is negative. Because of the electrical attraction of these oppositely charged solids, it was possible to remove negatively charged asbestos fibers from water by percolating water that contained suspended-asbestos through a porous bed of magnesium oxide particles. A bed of 100/200-mesh MgO was added to a glass tube with a cotton plug. Aqusous suspensions of 1 to 10 ppm cummingtonite asbestos (amosite), crocidolite, and chrysotile were percolated through this porous plug of MgO. Even though chrysotile is positively charged below pH 11, MgO is an effective filter medium for removing it. The highly basic MgO appears to cause the chrysotile to flocculate and attach to particles within the bed. Scanning electron photomicrographs indicated that essentially complete removal of the fibers from water was accomplished. Other materials tested as contact filter media and found to be ineffective or only partially effective were sand, calcite, carbon, diatomaceous earth, and cellulose. Acidic alumina collected amphibole fibers but not chrysotile fibers.

Jan 1, 1980

By Robert R. Dorfler

We ought not look back unless it is to de- rive from past errors, and for the purpose of profiting by dear bought experience. - George Washington During the mid 1960's, the application of automation was introduced to Climax by two process control companies. In 1969 Climax decided to seriously consider improved control of selected areas of their milling process after preliminary research had been completed on two rougher ball mill grinding circuits. In 1971 the Climax Mill Department developed a direct digital control scheme for rougher milling, designed a remote control center for handling process water, planned to automate the central steam heating facility for energy conservation, and convert other plant areas to automation. All twenty rougher grinding mills and the industrial water system were automated by 1977. The idea of automating central heating and other areas was abandoned although some fuel conservation items were installed at the heating plant. During this period from 1971 to 1978, the mill capacity was expanded from 39,000 metric tons per day to 43,000 metric tons per day and cyclone classification was introduced to rougher milling. Ore quality changes degraded the milling recovery from over 90% to less than 85%. This report describes the procedure the mill used in developing the automatic process and the occurances that affected the timing and fina1 control logic. The report deals primarily with the automation of the ball mill grinding, classification and flotation process as this was the bulk of the seven-year project.

Jan 1, 1979

By Douglas H. Bolton

In recent years, equipment manufacturers have been busy developing remote control systems to catch up with the sophistication and efficiency of continuous miners. Now the tables are turned, and manufacturers are undertaking the new challenge of upgrading, refining and equipping continuous miners to take full advantage of the capabilities made possible by modern, successful remote control systems. Because the operator can safely advance the miner farther without pulling out for roof bolting, continuous miners now need to be equipped with means of complying with correct face ventilation, dust suppression, methane detection, diffusion and improved lighting. Some of the exciting possibilities being developed to catch up with remote control include feedback controls using laser beams as datum points, coal sensing devices with feedback signals to show the operator what the machine is doing, show where it is relative to the coal seam, how hard it is working, and more sophisticated use of cyclic control. Mining machinery manufacturers have accepted the new challenges, and faster, safer mining procedures are already in sight.

Jan 1, 1975

By B. A. Kennedy

The instrumentation, monitoring, and prediction of a major slope failure at the Chuquicamata mine are described. In December 1967, pre-existing tension cracks on the south end of the east wall of the Chquicamata mine began to open. Various forms of instrumentation were installed for continuous monitoring. These systems included tension crack stakes, crack extensometers, linear extensometers, tape and transit lines, sliding wire contacts, and a seismograph. From the information obtained, the failure date was accurately predicted some five weeks before failure, enabling the mine to reroute truck and rail access; hence, causing a minimal mine shutdown of two and one-half days and preventing any injuries to persons or damage to equipment. The shape and form of the sliding mass are analyzed, as are the possible modes of failure.

Jan 1, 1970

By D. G., Bosse&apos

Equipment choices for ultrafine grinding encompass several different types of dry and wet size-reduction devices. These need to be put into functional perspective for systematic analysis of capabilities and limitations versus processing requirements of the materials to be satisfactorily ground. Particle strengths plus maximum and average sizes are the primary variables controlling grinding action requirements and equipment options for efficient processing. These are fairly well understood and provide the starting point for decisions. Particle space requirements under dynamic processing conditions vary with particle shapes and size-distributions by as much as 30X. This additional major variable is not widely appreciated and does need adequate description to provide a firm basis for selecting processing compositions and procedures.

Jan 1, 1983

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By K. Y. Haramy

A scale-invariant theory of the strength and deformability of rock masses in static equilibrium and at incipient failure is proposed. The theory provides a rationale for designing structures in rock. This paper presents results of experiments conducted by the U.S. Bureau of Mines and theoretical methods to determine and interpret in situ strength of rock masses using the borehole shear tester.

Jan 1, 1995

By F. M. Stephens

This paper is to be presented at the annual meeting of the American institute of Mining and Metallurgical Engineers, San Francisco, February 1959. Permission is hereby given to publish with appropriate acknowledgements, excerpts or summaries not to exceed one-fourth of the entire text of the paper. Permission to print in more extended form subsequent to publication by the Institute must be obtained from the secretary of the Institute. If and when this paper is published by the Institute, it may embody certain changes made by agreement between the Technical Publications Committee and the authors, so that the form in which it appears here is not necessarily that in which it may be published later.

Jan 1, 1959

By B. K. Mishra, B. Das, L. Panda, D. S. Rao

"The dissolution behavior of lateritic nickel ore containing 1.2% Ni, 40.6% Fe, 9.5% SiO2 and 9.59% MgO by sulfuric acid was investigated. The ore was characterized adequately by different techniques such as chemical analysis, scanning electron microscope (SEM), X-ray diffraction (XRD), field emission scanning electron microscope (FESEM), thermal analysis and Fourier transform infrared (FTIR) spectroscopic measurements. The characterization results did not reveal any distinct mineral phase for nickel; it was associated with mineral phases like goethite, hematite, chromite and serpentine in various proportions. The beneficiation studies by hydrocyclone, magnetic separation and flotation did not enrich the nickel value. Reduction roasting followed by magnetic separation indicated only 2%Ni with 28.9% yield. Consequently, the recovery of nickel values from the lateritic ore by acid leaching under different conditions was studied. The kinetics of leaching obey the first order rate equations. The recovery of nickel was found to be influenced by temperature. It was observed that at an acid concentration of 2M, leaching temperature 363 K, time 240 min and solid-to-liquid ratio of 1:10, it is possible to leach out more than 95% Ni.IntroductionThe demand for nickel is ever increasing. Nickel is used to impart specific properties to steel, titanium and aluminium, and also is used in petrochemicals, catalysts, batteries, etc. It has been estimated that nickel oxide ores account for about 70% of the world nickel reserves. However, most nickel is sourced from sulfide ores. Nickel is extracted from sulfide ore by size reduction, followed by flotation to obtain a nickel-rich concentrate. The concentrate is then pyrometallurgically processed by smelting to produce a nickel-rich matte after discarding an iron-rich slag. Due to the increasing demand for nickel in stainless steel and other alloys, nickel is also extracted from many secondary sources. The recovery of nickel from oxide ores is now gaining momentum, and more exploitation of this ore is being attempted by advanced as well as environmentally feasible, cost-effective techniques. Dalvi et al. (2004) has reported that, due to the increase in demand, the world nickel production from laterites is expected to increase every year from the current level of production. In recent years, investigations of the use of low-grade ores, spent catalysts, clays, etc., have intensified to meet the market demand and also due to a shortage of high-grade nickel bearing ores (Al-Mansi and Abdel, 2002; Baba et al., 2009; Ismail et al., 2011)."

Jan 1, 2015

By C. McKinnon

Climate change is the central challenge facing the mining industry, wherein producers must simultaneously ramp up production to provide the raw materials for clean technologies while transitioning to carbon neutrality. While transitioning to renewables will take time, mines can start improving energy efficiency while improving productivity today. This paper proposes a novel technology ecosystem that can help. By monitoring mine shovels, loaders, haul truck paths, and conveyor belts, the proposed technology enables particle size measurements throughout the operation, truck and belt volume monitoring, ground engaging tools monitoring, and boulder detection.

Mar 2, 2022

By H. Maleki

Interwest Mining Company has been collecting geologic data within the last decade in preparation for underground mining of extensive coal reserves in its Bridger Coal property in southwestern Wyoming. During a preliminary data collection program in 2000, Interwest Mining completed geologic investigations, including surface mapping, drilling, aerial photography, rock testing, and limited groundwater investigations. Core from 12 exploration boreholes in the area of interest was tested to determine the mechanical properties of the coal seam and the immediate roof and floor for evaluation of the feasibility of underground mining. Geologic investigations identified the presence of one 7-to-17-ft-thick coal seam throughout the reserve under 1400 ft of cover. During a geotechnical feasibility study in 2002, the authors reviewed available data while completing comparative analyses identifying critical deficiencies in these data. The study projected moderate-to-difficult mining conditions, considering the weak nature of near-seam strata and depth of cover, and thus recommended limiting the longwall reserves to an overburden depth of less than 900 ft. These shallow remaining reserves were located at depths within regional mining experience to justify longwall mining methods. Based on a critical examination of available data, Bridger proceeded with more detailed data collection to improve understanding of the depositional and structural setting of the reserve, hydrogeologic conditions, overburden strength, and premining stress conditions. Additional data was collected during 2003 and 2004 field programs. Since 2003, Bridger has had the opportunity to observe ground behavior in a series of up to 1200-1600-ft- long rectangular openings created during highwall mining. These narrow unsupported openings remained stable in the short term in large areas but the overburden subsided locally in the long-term depending on geologic and panel layout designs. These localized subsidence events allowed an examination of in-situ coal strength based on back analyses of stress. The unextracted highwall areas near Ramp 17 provided an ideal location to access the underground reserves using a 6-entry set of mains. The existing north-south oriented longwall layout for the Bridger Coal was selected by Bridger to maximize resource recovery from the D41 reserves while considering operational and geotechnical constraints. At 45-degrees deviation from preexisting joints and mild horizontal stress field, this orientation was considered beneficial for overall stability while using both sets of joints for facilitating the caving process. The present layout utilizes pillars on 80- to 90- by 200-ft centers, 17-ft entry spans and 750-ft wide longwall panels (Figure 1). Gate pillars are on wide spacings and are intended to act as abutment-abutment pillars to limit strata deformation over the gateroads during longwall mining.

Jan 1, 2008

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By Prakash C. Kapur

A principal first order and a minor summation term contribute to the solution of the discretized batch grinding equation when formulated in cumulative retained mode. Depending on the interrelationships between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The implications and advantages of the reduced grinding equations are briefly discussed.

Jan 1, 1969

By John R. Buzek

Thickeners are simply large tanks, usually circular in shape, which are designed to allow settling of solids and to operate with continuous overflow of clear water and underflow of thick pulp. The dimensions of the thickener are usually such that dewatering of very fine pulps may be accomplished while still 1 overflowing clear water. Some thickeners such as the Genter, Hardinge and Hydrotator types combine thickening with filtering2 while others such as the Dorr type are pure thickenersl,2,3. A schematic diagram of the traction type Dorr thickener is shown in Figure 1. This type is appropriate for tanks over 15 m (50 ft) in diameter. This tank employs a rotating raking mechanism which moves the settled material toward the central discharge. For this and other thickeners, it is common to have a shallow conical tank bottom in order to conform to the geometry of the raking mechanism, and it is often desirable to elevate the tank for ease of access to the product. When the tank does not rest on the ground, the forces resisted by the cone are large, and thick plates must be employed. The fabrication of these tanks requires temporary supports in order to erect the cone. A flat-bottomed tank could also be used because the settled material would soon form a hardened conical surface. However, because of the presence of large bending forces, even larger plate thicknesses are required than for the conical bottom. Significant cost savings often can be realized by the use of a scalloped-bottomed tank such as the one partially shown in Figure 2. The particular scalloped bottom discussed in this paper (and shown in the Figure) employs radial beams forming the outline of the cone-shaped bottom. These beams are supported directly by columns. Cone segments are hung between adjacent beams. The exact geometry of these segments depends upon the cone angle and radius, the number of radial beams, and their inclination. The geometry is chosen to satisfy certain clearance restraints and to utilize the material as efficiently as possible. The resulting thickness of these segments is significantly less than that of the

Jan 1, 1977

By Christopher J. Bise

Traditionally, mine drainage systems have not received the high level of emphasis on careful engineering design which has been rendered to many of the other auxillary operations. This may be due, in part, to the situation-response approach toward dealing with an influx of water. When the installed system becomes inadequate, costly alterations to the pump, such as staging or speed increases, are considered expedient solutions. In order to rectify this situation, computer-aided solutions to mine drainage problems could represent an efficient alternative to the methods presently used. This paper will consider the application of microcomputer technology to mine drainage problems and will show how the relative economy and convenience of microcomputers can make them become valuable analytic tools at any mine site.

Jan 1, 1983

By Ronald B. Stone

This paper describes a proposed solution to the problem of mining a 315 foot diameter unsupported sphere at a depth of 2700 feet in a salt dome by conventional mining methods. The proposed solution utilizes many of the varied technologies available to the mining engineer for solving mining and underground construction problems. The following are reviewed in the paper: A. The location of the sphere within the dome as required by construction criteria. B. The relation of the location of the access shafts to the sphere. C. The rock mechanics theory in relation to the salt dome and large size of the excavation. D. The proposed "honeycomb" method of mining which will be a partial answer to rock mechanics stability requirements. E. The equipment which it is recommended be utilized to accomplish the construction. F. The rock mechanics measuring instruments proposed. G. The methods of disposal of the mined salt. Conclusions and areas of further study are outlined in the final statement.

Jan 1, 1968

By T. Glenn Pobanz

For more than fifty years Walter Kidde & Company, Inc. has engaged in the development and manufacturing of both fire suppression and detection equipment. Our initial work for the mining industry centered around dry chemical extinguish-ing equipment for mine haulage cars. To fulfill this need, Kidde engineered and developed a manually activated dry chemical system to provide protection for the wheel wells, cable reels, and motor compartments on various pieces of underground mining equipment. The next phase of mining operation fire protection for Kidde was the area of detection and automatic fire suppression for conveyor belt heads. Early in 1970, a field evaluation program and belt head demonstration unit was taken to 10 areas throughout West Virginia, Kentucky, Pennsylvania, and Ohio. This extensive field program was a joint effort with National Mine Service Company of Pittsburgh, Pennsylvania. The objectives of this program were to study mine hazard problems and to determine further requirements of mine operators. The resulting belt head detection system centered around our Continuous Strip Thermistor Core heat detector in conjunction with a Kidde stored pressure dry chemical extinguishing system. Continuous Strip detection has been in use for a number of years in aerospace applications. It has proven flexible and reliable for the rapid detection of overheat conditions and fires in engines of over half the aircraft flying today. The use of Continuous Strip gave us flexibility to protect surface areas over and around the actual conveyor belt head equipment. The nature of Continuous Strip allows us to bend, wrap, and attach the 20 foot long thermistor element over the desired protected points of the belt head. An integral part of the conveyor belt head protection system is the control panel utilizing our comprehensive knowledge of fire alarm control logic. This panel contains supervision circuits which sound trouble signals upon detecting a break in the Continuous Strip; breaks in the wiring to the remote electrical extinguishing activators or to the alarm bell; or loss of primary power. A separate control module provides the adjustable alarm temperature setting of the

Jan 1, 1971

By I. M. Konduri

Theoretical investigation and laboratory experimentation have shown a great potential for jet fan ventilation in mines. Jet fans, also called induction fans due to the induction effect of the fluid jet to ventilate headings, may have particular application in remote-controlled production operations. This paper summarizes ongoing research using a scaled laboratory model. The model uses water as a fluid medium and simulates a typical 25m long heading of 1.5mx6m cross-section. The effects of various nozzle positions and designs have been investigated by using still photography as a tool for flow visualization. It is also found that the use of jets in combination with line curtains has enhanced the overall ventilating effect in the model entry.

Jan 1, 1996

By Robert E. Ennis

Several important economic variables must be studied when planning a major underground conveyor haulage system if the objective of tow cost haulage is to be met. The purpose of this paper is to call these economic factors to the attention of the mine planner and encourage their serious consideration. To illustrate, the importance that some of these variables hole for the mine operator who wishes to reduce costs and maintain sound belt haulage practice, these areas of discussion will be covered. 1. Selection of economical flite lengths. 2. Economics of wire rope frame vs. rigid frame conveyors. 3. How idler design affects conveyor costs. 4. Economies in drive design. 5. How speed affects conveyor cost. 6. P.V.C. vs. Neoprene belt - what savings? 7. Maintaining, conveyor investment through maintenance. 8. Miscellaneous factors affecting the cost of belt haulage.

Jan 1, 1967

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970