Search Documents

By Alexandr A. Abramov, Svetlana M. Angelova, Oleg P. Maljuk

In this paper the effect of the ratio of grinding and grindable size classes (ore lumps, particles and grains) and the guantity of intermediate size classes in the feed of the primary wet autogenous grinding "Cascade" mill is studied and the features of the influence of these factors on the mill capacity are shown. On the basis of the experimental data from Lebedinsky mineral processing plant, where magnetite guartzites are processed, a coefficient of the "total ratio of size classes" in the feed of 9x3 m "Cascade" mill was estimated. It helps to get an evaluation of the effect of ore size classes ratio in mill media on the mill capacity and to work out some ways for its optimization in closed or semiclosed technological circuites of primary autogenous grinding. The operation of the specific energy effects for some intermediate size classes, removed from the mill as circulating load, is proposed to improve its efficiency before regrinding in "Cascade" mill and decrease negative influence of such classes accumulation in the mill media.

Jan 1, 1995

By J. Stachulak

This paper deals with theoretical considerations and practical applications of ventilation network calculations, based on mass flow rates and performed by computer simulation in our deepest operating mine - Creighton. The paper also deals with natural ventilation. In the usually accepted air-flow theory, the air is assumed to behave like an incompresssible medium. This introduces considerable error where temperature and pressure changes are great. Therefore, any study of the air flow in deep mines, must take into account compressibility. Basing ventilation calculations on mass flow allows a distinction to be made between air leakage and such quantity changes which occur due to air density changes. The energy which is required to convey one pound of air through a mine can be obtained by adding all head losses hL (ft-lb) of the ventilation paths through which the air flows. However, this total energy will not be correctly expressed in a compressible fluid by summing all pressure losses PL = hL x d (ft-lb/ft3 = lb/ft2) d = density. There is a law of mass conservation, but no law of volume conservation. Natural ventilation is caused by the conversion of heat into mechanical energy and not by the difference in upcast and downcast densities, as often believed. In an existing mine natural ventilation can be determined correctly by plotting a pressure volume diagram and measuring the area ? [ ] vdP = hN, where v = specific volume, or by measuring the sum of all friction losses and work provided by a fan. These procedures are tedious. The natural ventilation head (hN) can be approximated by the equaticn hN =[ ] tdZ. Where T is the average absolute temperature, t air temperature and Z elevation. In Prof. R. Greuer's computer program this determination of hN is automatically done for every mesh of the network.

Jan 1, 1980

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

Reducing the contribution of heavy- and light-duty diesel-powered equipment to concentrations of aerosols and gases is essential to industry’s efforts to improve air quality in underground mining operations. The results of this study demonstrated a potential of control strategies based on retrofitting existing power packages with diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) systems and repowering existing systems with advanced power packages to reduce contributions of diesel-powered vehicles to concentrations of diesel aerosols and criteria gases in underground mines. The implementation of viable exhaust aftertreatment systems and advanced diesel power packages could be instrumental in the underground mining industry securing a clean, economical and dependable source of power for mobile equipment.

By J. McCreedy

The Ontario Division of The International Nickel Company of Canada, Limited, operates five underground mines and one open pit on the rim of the Sudbury Basin located in the Province of Ontario, 230 miles northwest of Toronto. Four of the mines, Frood-Stobie, Creighton, Murray and Garson, lie on the South range of the Basin within a 10-mile radius of the City of Sudbury; the fifth mine, Levack, is on the North range, about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, the principal minerals being pentlandite and chalcopyrite. Other elements recovered from the ores in varying quantities are platinum, palladium, ruthenium, iridium, rhodium, cobalt, selenium, tellurium, iron, sulphur, gold and silver. In 1962, the total underground ore production was over 10,800,000 tons which was mined mainly by blasthole and caving methods with the remainder by cut-and-fill, square set, and undercut-and-fill techniques.

Jan 1, 1964

By A. Janwong

Ion exchange technology is becoming more prevalent for metal recovery from low concentration solutions. The products of ion exchange are typically a metal free stream (product stream) and a concentrated metal stream (byproduct). The metals in the concentrate stream are usually precipitated and returned to the process or discarded. The unique features of emew® technology enable metals to be recovered directly from the concentrated stream. The advantage of the IX-emew® combination is the ability to have two product streams: 1) clean metal free solution and 2) metal product for sale. In addition to recovering metals from solution, it is also possible to separate metals from each other and recover more than one metal product. In this paper, examples of IX-emew® combinations are detailed including the recovery of copper, nickel and cobalt from an industrial waste stream, recovery of nickel from a spent electroless nickel plating solution and recovery of cobalt from an hydroxide cake.

Feb 23, 2014

By David Muir, Slobodanka Vukcevic

Gold is commonly associated with copper minerals, particu­larly in the more geologically recent rocks of Northern Australia, Chile and the Pacific Rim. Traditionally, oxidised copper-gold ores are selectively mined and processed for gold by cyanidation, ensuring that levels of reactive copper in the ore are kept low to minimise cyanide consumption; whilst sulphide copper-gold ores are floated and gold is ultimately recovered as the by-product from copper smelting and refining (La Brooy, 1992). Very few process­ing options exist for treating copper ores which cannot be selec­tively mined or floated, and for treating floation tailings which often contain significant gold (Muir et.al.,1989). The ammonia-cyanide leach system stands out as a unique method of selectively extracting gold without copper using economic levels of cyanide (1-2 kg/t NaCN) and ammonia (1-5 kg/t). Although first patented in 1904, it proved difficult to control and predict per formance with different ores. However, recent research and development in Western Australia by Ruane (1991), Hayes and Corrans (1992), La Brooy et.al.(1991), Muir et.al.(1993), Muir and La Brooy (1993), has led to an under­standing of the mechanism, and the commercialisation of the process at the Paris Dump (W.A.), Akjoujt (Mauritania), and in the Eastern Transvaal (Laxen,1994). Efforts are now underway to pilot and develop a tailings treatment plant at Telfer following successful laboratory trials. To date, process optimisation has relied on trial and error and large numbers of tests covering a range of conditions. Thus the results are specific to the ore. At Murdoch University, process optimisation is now focused on measuring and control­ ling Eh, pH, NH3 [Cu(II)], and Cu-CN species at the optimum levels identified from the recent mechanistic studies. In this way, the optimum composition required to process any ore should be readily established and maintained.

Jan 1, 1995

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By Richard L. Wedertz

Although the physical appearance of excavating equipment doesn't seem to have radically changed over the past decade, important changes within the products and an innovative attitude on the part of the engineer in his design approach is becoming increasingly evident. The new philosophy is to go beyond simple refinements of existing designs that simply produce a machine which further reduces overall cost per ton or per cubic yard of material moved and to do it more efficiently than ever before. Standard ideas and preconceived notions have been discarded and have given way to providing a design and a machine that is best suited to get the job done. Understanding that the application will not always fit the machine, but, in most cases, the machine should fit or suit the application is a foremost consideration in the engineers' design criteria.

Jan 1, 1973

By Agne Rustan

INTRODUCTION This work is a continuation of the preparatory study by Rustan and Stöckel 1979 (3) and (4) of the possibilities to introduce automatic mine ventilation in Swedish mines and construction works. The preparatory study has been financed by the Swedish Board of Technical Development. In the study it was recommended that an automatic step by step control of the fans near the working place due to diesel exhaust emission would be the best solution. A more advanced alternative would be to regulate the fresh air continuously in proportion to the contamination. The latter alternative has been studied by Boliden Mineral Co in the Udden mine. In this study it was found that the air supply could be regulated continuously but it was very important where the sensors feeling the contamination were placed. An intense study of the environment underground is now being planned by our division together with specialists from the National Board of Health and Safety, The Swedish Work Environment Fund, LKAB and the local Governmental Inspection of the Workers Safety. Different gases, radon, dust, airspeed, moisture temperature and pressure is planned to be measured continuously and correlation between the parameters is going to be established to decide the best measurement parameters for regulating the system. The best situation of sensors is also going to be studied. Despite this work hasn't been done yet this paper covers some of the problems which could be encounted with continuous regulation. In this report the environment has been studied during the test with step by step regulation of fans by radio. Diesel vehicles are the largest polluters under ground in Swedish mines and we have therefore suggested that the large diesel vehicles should regulate the fans. The goal of this study has therefore been to find how active diesel vehicles should be able to start and stop gallery fans at both intake and return air. In this paper different methods for activating fans are discussed. Then the best methods are chosen and tested in the mine. In this study we have found that changes of temperature is a cheap and effective method to start and stop cross cut fans in sublevel caving and radio signals seem to be an attractive system for start and stop of gallery fans. This work has been done in close collaboration between LKAB in Kiruna and the University of Luleå - Division of Electronics and Division of Mining and Rock Excavation. A reference group for the project has been established with ventilation experts from the mines, representatives for the local mine worker's unions and authorities from the local Governmental Inspection of the Workers Safety. VENTILATION SYSTEM STUDIED In the project the ventilation system at LKAB in Kiruna has been studied. The mining method used is sublevel caving with 9-13 m slice height. The air is heated winter time over ground by hot water heat exchanger. The main fans are pushing air down to a main distribution level along the 4000 m long and about 100 m wide orebody. From the distribution level, air is taken through shafts down to the sublevels, where it is pushed through the levels by local gallery fans on both intake and return side, see fig 1. The air ( ~ 8 m3/s) is moving freely through the gallery head. The cross cuts are ventilated with smaller fans, diameter 500 mm, and flexible duct, see fig 2. The aim of this study has been to study how to start and stop gallery- and cross fans and examine the environment when the fans are stopped . In Sweden there are no regulations telling that a minimum of air amount must be supplied. Instead the hygienic limits must be fullfilled.

Jan 1, 1981

By R. V. Ramani

An improved mine environment is the single most critical factor affecting the health and safety of workers engaged in underground coal winning. A very important subclassification of this wide field is mine ventilation, which essentially deals with 'mine atmospheric environmental control.' To ensure proper mine atmospheric environmental control, adequate quantities of air must flow through working sections in the mine. In recent years much attention has been paid to the fan and its prime movers, but the efficient use of the fan output in the workings has not received an equal amount of investigation. In mechanically ventilated mines friction losses in main airways often account for 70 to 90 percent of the total pressure loss sustained in the system. Also the leakage losses are a serious detriment to the efficiency of mine ventilation systems. It is not uncommon to loose 60 to 70 percent of the air between the fan and the last open cross-cuts due to leakage directly into the return Proper assessment of these losses in simulating and projecting complex ventilation systems is vital. Network analysis of ventilation systems is not new. Scott and Hinsly (1951) presented the detailed mathematical framework. Since then work has been done in adopting this technique to analog, and within the past few years, to digital computers. Development of computer programs to solve ventilation network problems has been reported in United Kingdom, Japan, U.S.S.R., South Africa, Germany, and the United States. The purpose of these programs is to serve as an experimental mine wherein analysis of proposed alternatives or ventilation planning can be tested. The great power of the computer as a planning tool lies in the ability to input empirical or Projected data into programs with predicting ability. But, however good a computer program is, unless fairly accurate input information is available accurately assessing the engineering factors of the ventilation system, the output will be suspect. Thus, to simulate and project mine ventilation systems, good estimates of leakage and friction factors are important. Yet, relatively little work has been done in the past three decades to determine these more realistically.

Jan 1, 1973

By John P. Weir

The planning of an underground mine for successful extraction of a bedded deposit in sedimentary rocks requires the integrated evaluation of many interdependent problems. The development and coordination of feasible solutions are the responsibility of the mining engineer. One of these problems will be discussed herein; this is the design and .layout of mine workings to secure effective control of the strata above and below the deposit. The objective is the simplest possible repetitive system permitting safe maximum recovery at optimum cost. Mining conditions to be encountered must be predictable. The best mining equipment is ineffective unless strata are controlled. Conversely, a mining layout is only of academic interest, if equipment can not be adapted to work it with adequate provision for ventilation, compliance with mining laws, proper ingress and egress and other practical requirements. Strata control, then, is but one of the mining engineer's problems, and the solutions must be worked out concurrently with solutions to other problems. Dr. Karl F. Fetters in his introductory remarks before the Fourth International Conference on Strata Control and Rock Mechanics at Columbia University said that mining engineering ?has come from the stage of empiricism backed by intuitive reasoning, to where it is based on fundamental scientific and engineering principles?. The standard curriculum in mining engineering now reflects such a change. In common with other branches of engineering education, less and less emphasis is placed on practical skills and more and more on broad scientific education. Science, research and the quest for basic truth are stressed, while descriptive courses and the teaching of specific skills are limited.

Jan 1, 1966

By W. L. Price

The intelligent selection of wire cloth and perforated plate for screening surfaces seems a rather confusing subject to the newcomer in aggregate processing. The proper application of various screening surfaces is a complicated one and one could consider himself an expert only after many years of working with all applications. However, part of the subject matter could be simplified considerably for, the average screen user. In this paper an attempt will be made to do this, by presenting some comparative specification data along with cost figures Unfortunately, it is impossible in the limited scope of this paper to give actual service comparison records between different cloths or cloth and plate. Anyone who has considered making actual service comparisons for competing screening media is well aware of the almost insurmountable problems Their solution would form the basis for a separate paper on that subject alone. Therefore, this paper will be limited to comparative data up to the point of installation.

Jan 1, 1961

By Robert J. Clarke

Reflections on over ten years experience handling bituminous coal from railroad cars to ground storage and lake vessels. The arrangement of the facilities is described but the basic theme of the discussion is the experience gained and lessons learned from facility operation. The Great Lakes provide the maritime environment for the economical transport of vast quantities of raw materials from their source in the Upper Lakes (the Mesabi Range, for instance) to Lower Lake Ports. Lake Erie, because of its proximity to the steel centers , blossomed with the great ports that now line its southern shore - Toledo, Sandusky, Lorain, Cleveland, Huron, Ashtabula, Conneaut and Erie.

Jan 1, 1981

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By John Newby, Ulf Gwildis, Ken Massé, Guillaume Roux

How to connect an effluent conveyance tunnel to riser shaft and diffuser arms of an outfall system is dictated by the ground conditions, which ideally include rock or soil strata of low permeability. Where such favorable conditions are beyond reach, both the complexity of designing and the risk of constructing this crucial system connection increase disproportionally. This paper describes the considerations that went into the approach of connecting a 5-m-diameter TBM drive with the in-river riser shaft of the Annacis Island WWTP New Outfall System in the highly permeable Fraser River sands at hydrostatic pressures exceeding 3 bar.

Jun 23, 2024

By R. D. Peterson

Autocad has become the standard graphics package for the mining industry as well as the general engineering profession. This paper discusses the evolution that mine planning has undergone and the trend toward compatibility with Autocad. It discusses the common use of Autocad in mine planning and systems modeling using a program called ICAMPS developed by Ohio Automation. As an example of its usefulness the use of the interactive ventilation network modeling capabilities are discussed specifically and are applied to mine planning at an operating trona mine. The ventilation analysis feature of the ICAMPS software works from Autocad drawing of the as-mined map and the projected mine layout. Using on-screen displays of these maps and the snap-on feature of Autocad, the planner designates nodes in the ventilation network, connects them into branches and selects branch characteristics from a side bar menu. The color coded ventilation network appears with the branch parameters alongside each branch. The software calculates the length of airways, computes the branch resistances where needed, converts the input into the required format and passes this information as input data along to the PENNVEN simulation program written by the Pennsylvania state University. Output is available in graphical as well as report format. The color coded graphs include pressures at the nodes and flow quantities on the branches. Since the networks come from the mine maps, the ventilation schematic displays are to scale and can be plotted separately or superimposed on the mine maps.

Jan 1, 1995

By Eugene P. Pfleider

The mining industry of the World, and particularly of the United States, has made a complete reversal from underground to surface mining methods since the turn of the 20th Century. This has occurred even as average ore grades were decreasing and strip ratios rising. In the early 1900's there were over 100 underground mines producing from the three iron ranges of Minnesota -- today there are hone. Practically all of our coal prior to 1930 was mined underground; today over one-third is from surface operations and that percentage is increasing. Although world mining has hot changed to surface techniques as rapidly as has the U. S. Industry, the shift is escalating and will approach our figures shortly. A comparison of World and U. S. production figures are shown in Table 1, taken from the AIME Surface Mining volume, and the trend rates for the U. S. are depicted in Fig. 1.

Jan 1, 1968

By Charles Kocsis, Pedro Nascimento, W. Patrick Arnott, Samuel J. Taylor

Respirable crystalline silica (RCS) is an inhalation health hazard for mining and industrial work environments and must be monitored. We provide theoretical analysis of real-time measurements for determining RCS mass concentration without the use of filters by using photoacoustic spectroscopy. The suspended dust in the mine air can be continuously sampled by the photoacoustic instrument. A tunable quantum cascade laser is the light source, allowing for determination of interferences such as kaolinite, coal dust, and water vapor. The most useful spectral region is found to be between 11 and 13 μm. Absorption by water vapor, and, to a lesser extent, carbon dioxide, in this spectral region has gaps that allow for quantification of the aforementioned dust species as well as a convenient check on the calibration of the instrument. This work brings photoacoustic measurement of aerosol to the mid infrared range where spectrally dependent light absorption can be used to quantify dust composition and mass concentration.

Jul 31, 2022

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996