Search Documents

By Allan M. Hale

The central Florida phosphate industry is not a recent development. The first phosphate mining occurred in approximately 1888 (1). Many of the original mining companies were "wildcat" operations operated with rapid phosphate extraction as the sole purpose and no long-term commitment to development. Many of the early pioneers were ill-equipped to mine phosphate at either a practical or economical level; as a result many of these early companies "folded" after only a brief period of operation. However, as these early companies went out of business, several large companies developed, expanded their mining territories bought up the folding companies and by 1903 (little more than 10 years after the first mines were started), approximately 37 of the original 60 mines were control- led by three major companies (1). In the early period, mining reclamation was nonexistent. The mined out areas were left to revegetate and reclaim "naturally" over the period of many years. Reclamation practices were only started relatively recently and the various reclamation techniques developed and used in the past have continued to be employed with varying degrees of success through the present time. The reclamation techniques used in the past and currently include land and lakes restoration, sand tailing reclamation, slime ponds reclamation and overburden fill.

Jan 1, 1980

By Joel K. Waterland

The Homes take Mining Company at Lead, South Dakota has a yearly production of 1,868,741 tons of ore produced from horizontal cut-and-fill stopes and timber cut-and-fill stopes. This production, in addition to the necessary development (drifts and raises), requires 5,168,271 feet of drilling annually. The rock for the most part consists of quartz; mica schist; and cummingtonite schist; and must be considered as relatively hard. Penetration rates average about 15 inches per minute using an operating air pressure of 100 psi. The rock is tough, rather than brittle, and dulling occurs quite rapidly. The average regrind period is approximately 19 feet per regrind using a 1-7/16 inch carbide bit. At the present time, all drilling is accomplished with 2-5/8 inch bore airleg mounted drills, and 2-3/4 inch and 3-inch diameter bore -stopers (raising only). These machines are all direct striking, with 4-1/4 inch chucks. 7/8-inch hexagonal carbon drill steel with forged collars are used in conjunction with 1-7/16 inch multi-use, threaded, carbide bits. 62,793 rods, and 16,234 bits are used to maintain the yearly production. The number of rods noted are the rods that were sent: underground, both new and reconditioned.

Jan 1, 1963

By T. E. Kobrick

When Ralph Banks called and asked if I would agree to present a paper on environmental health in the coal industry, I was reluctant because I have not been actively involved in coal mine dust control on a day-to-day basis for a number of years. Ralph reminded me that I am one of the few industry people with an industrial health background who remembers the pre-1969 Federal Coal Mine Health and Safety era. This marks the second time within the past year that I have had a similar request based on the same basic reasons. While I was pleased to have been remembered, I'm beginning to feel like the football player who has played one too many games. In responding to Ralph's request to present an overview of the past, present and future of environmental health in the coal industry, I have attempted to take the broad approach of someone who, having been intimately involved in an area of endeavor for a number of years and then leaves, has an opportunity to revisit that area at a later date to see what has changed and what remains the same, what have been the successes and the failures. Since none of us can foresee the future, trying to project too far ahead is fraught with frivolity, except that unless one is foolish enough to accept a future invitation to review those predictions compared to actual events, no one will recall how accurate or inaccurate those projections might have been. I can assure you that I will not ask to accept that challenge, so you can rest comfortably that five years from today you will not be asked to sit through a similar presentation by me - and that's a promise.

Jan 1, 1985

By Bastiawarman Rifki, Nugraha Nico, Priatna Anton

The Deep Mill Level Zone (DMLZ) is one of the underground mines operated by PT Freeport Indonesia (PTFI). DMLZ is located approximately 1,500 m below ground level, where dominant rock types are skarn and diorite. The DMLZ mine and layout was designed based on the previous mine located above ground, the Deep Ore Zone (DOZ). The DOZ mine, located approximately 1,000 m below ground level, was a proven success, with a maximum capacity of 80K tonnes per day. During the production ramp up, which started in 2015, the DMLZ experienced several seismic events. The most significant event occurred in January 2018 with a recorded magnitude of more than 2.0 Mw, which resulted in a 14-month delay of the undercutting until March 2019. The significant event in January 2018 required the DMLZ to apply several adjustments related to the mining plan to help ensure it could continue development and achieve production target safely. This paper will describe the changes in the DMLZ mine plan as a response to the seismic activity at the mine, the reason behind the decisions being made to change the mine plan and strategy, as well as strengths and weaknesses between the previous plan compared with the new plan.

Apr 26, 2022

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By Steven A. Bradbury

INTRODUCTION Passive dust control systems are quickly gaining acceptance in the bulk solids handling industries. The number of applications is increasing due to proven performance, especially in US power plants burning Powder River Basin coal. Air Control Sciences ®, Inc., of Boulder, Colorado, has over forty (40) patented Dustless Transfer ® systems in operation. All of the installations control workspace dust levels to less than 2.0 mg/m3, and in some applications reduced conveyor dusting by over ninety-eight percent (98%). Passive systems control fugitive dust emissions by minimizing the induced airflow in bulk material transfer and slowing its velocity. Traditionally, fugitive dust control in the mining industry was accomplished using either dust collection systems or dust suppression systems. The term passive dust control, indicates these methods don't use any active dust collection or suppression. Passive dust control systems are best suited to transfer from one conveyor to another. They can also be applied to transfers from feeder to conveyors.

Jan 1, 2004

By S. K. Mishra, S. B. Kanungo, D. Biswal

An attempt was made to beneficiate low-grade, high-phosphorus manganese ores of the Garividi-Garbham region of Andhra Pradesh, India, by using wet high-intensity magnetic separation (WHIMS). The distribution behavior of both mass and chemical constituents in different size fractions of a typical highly weathered ore sample was studied to obtain information about the liberation characteristics of various chemical constituents. Magnetic separation indicated that in the +208-µm size fractions, P and acid insolubles were concentrated in the magnetic fractions. However, in the -208-µm size fractions, P and acid insolubles were concentrated in the nonmagnetic fraction because of a lower recovery of the magnetic fraction. Variations in field intensity between 1.3 and 1.75 T had little effect on the recovery and the grade of concentrate. The results also demonstrated that phosphorus was associated with all three major constituent phases, namely, oxides of Mn and Fe and aluminosilicate gangue minerals.

Jan 1, 2000

By Alexander Sutulov

It is calculated that since the beginning of last century, which practically coincides with the beginning of the Industrial Revolution, our civilization has consumed around 239.5 million tons of copper (see: Table 1). According to the most pessimistic projections of today, with only a 2.5% annual growth rate in demand, we are bound until the end of this century to consume another 200 million tons of copper in remaining 17 years. A recent study made by US Bureau of Mines (1) indicates that the proven ore reserves of 150 major operating mines and about 120 deposits sufficiently explored for development and feasibility studies accumulate a total mass of 49.3 billion tons of ore, assaying an average of 0.82% Cu and containing around 324 million tons of recoverable copper. Consequently, there is a high grade of probability that the bulk of our future ore supplies, for our demand of, say, next 25 years will cane precisely from these mines. The interesting point in USBM study is that it indicates the recoverable byproduct content of these ores and which is: 118.2 million troy ounces of gold 2277.4 million troy ounces of silver 7.1 million tons of lead 24.7 million tons of zinc 1.3 million tons of nickel 3.1 million tons of molybdenum 765 thousand tons of cobalt, and 720 thousand troy ounces of platinum. This information gives us a relatively reliable profile of our future ores for next 25 years, and thus makes possible evaluation of byproduct credits in our future copper mining and producing activities.

Jan 1, 1983

"HISTORY Tube bundle systems have been used in the coal mining industry for gas detection since the 1960’s. At the time there were developments were underway for improved gas monitoring systems. The primary gas detection systems in use were the flame safety lamp, colorimetric stain tubes and the taking of samples for analysis by gas chromatography. The MSA D6 hand held methanometer was approved in the UK for statutory methane measurements in 1972 and became very popular due to its smallness and simplicity of use. In 1973 Sieger Limited also developed a BM1 methanometer which could be installed underground and relay methane concentrations to the surface. Similar developments were underway for carbon monoxide detection and one was developed in 1982 by the Yorkshire Regional Laboratory of the NCB commercial development was undertaken by Sieger Limited who named it the ‘SCO1’. The UNOR 1 carbon monoxide and methane analyzers were approved for underground use in the United Kingdom in the late 1960’s.5 The technique was developed by Dr Luft of Bergbau-Forschung Essen and the equipment was manufactured by Maihak in Germany. The apparatus was flame proof and provided an intrinsically safe output which allowed the result to be telemetered to the surface through colliery communication systems. Both analyzers work on the same principal and each of the gases adsorb a certain wavelengths of infrared radiation. The detector measures the residual transmitted radiation and determines the percentage of gas present in the sample. These flameproof versions had proven to be robust and reliable. The UNOR 1 had been used in the Saar region of Germany and Scotland in the UK. The development of tube bundles for hydraulic controls enabled the development of the tube bundle gas monitoring systems we know today. A bundle of tubes are taken underground through a shaft, a borehole or drift then distributed to the required monitoring points. This enabled the ongoing monitoring of the underground environment when the power was isolated at 1.25% CH4. In 1972 the United Kingdom (UK) National Coal Board (NCB) produced a hand book for tube bundle systems which was subsequently updated in 1974. This is a useful guideline into the operational aspects of tube bundles systems at coal mines6. Many of the processes identified are being followed today. The United State Bureau of Mines (USBM) prepared a circular similar to the NCB handbook on tube bundle systems.7 The circular was prepared by Litton C and it was targeted at the design criteria for tube bundle the systems. The circular also states that “pneumatic monitoring systems can be used to monitor for hazards that develop quite quickly”."

Jan 1, 2016

By A. Habibi

The FMC Westvaco Trona Mine is located near Green River, Wyoming and has an annual production of 4.5M tons. Trona is an evaporite mineral that is processed into several products, mostly soda ash. The underground mine has two active development panels and one longwall (LW) panel. The mining horizon is about 500m below surface and the surrounding strata liberates methane. Three surface-based, blowing fans provide ventilation air as a positive pressure system. The mine operates a 225m long LW face, built by Joy Mining Machinery. Headgate and Tailgate developments are driven with four entries. The recovery room, at the end of each panel, is 8m wide with three access chutes. Additional recovery room support comes for concrete blocks used with a center to center spacing of 1.5m. As the LW enters this pre-driven recovery room there are notable responses and shifting ground stresses. This study was undertaken to measure the ground response using seven vibrating wire displacement transducers. These devices were used to monitor the convergence as the LW approached the recovery room. The methane concentration in the air ventilating the recovery room was also monitored. The correlation between convergence and gas liberation was then studied. The results show that the convergence varies from 0.1m to 0.25m along the length of the recovery room. Ventilating the recovery room becomes critical as methane is liberated from oil shale as the more plastic floor material is disrupted. Appropriate methods are employed to ventilate the recovery room.

Feb 23, 2014

By Phillip J. Maddex

During the last 10 years there have been many new developments in transport and handling equipment. Important technical and economic developments that can be used to reduce costs are; new terminal and materials handling concepts large river tows - 40,000 tons and 9000 hp towboats slurry loading and unloading of ocean vessels long distance pipelining of solids development of the shuttle train (unit train) large ocean barges ? 25,000+ tons ? pushed & towed 150,000 ton self-unloading super tankers - 300,000+ tons container shipping Some of these developments have been discussed at SME meetings in papers describing the transportation of minerals from new mines. But, only a few papers described improved transportation from older operations. Since transportation is a major part of the delivered cost for minerals, the economic benefits to be gained by putting new transportation developments to work are very substantial. Frequently good transportation planning and management makes the difference between a marginal ore body and a very profitable one.

Jan 1, 1972

By J. Brad Dalton, Sam Vance, Trude V. V. King, Roger N. Clark, Raymond F. Kokaly, Gregg A. Swayze, Dana J. Bove

Visible-wavelength and near-infrared multispectral image cubes for the Animas River Watershed from Hermosa, Colorado to the headwaters at Animas Forks, Colorado were acquired on June 18, 1996 using the Jet Propulsion Laboratory's AVIRIS (Airborne Visible and InfraRed Imaging Spectrometer) instrument (Green et al., 1998). These image cubes have been analyzed using the USGS Tetracorder V3.4 implementation (Clark et al., 1995), an expert system which utilizes a database of more than 300 laboratory spectra of endmember minerals and mineral mixtures to generate maps of mineralogy, vegetation coverage, and other material distributions. Major iron-bearing, clay, carbonate, and other minerals were identified along with several minerals associated with acid-generating hydrothermal systems including pyrite, jarosite, alunite and goethite. Additionally, distributions of alkaline minerals such as calcite and chlorite indicate a relation between acid- buffering assemblages and stream geochemistry within the watershed.

Jan 1, 2000

By Hugh D. Olmstead

Typical operations necessary to develop oil and gas reservoirs are reviewed, including exploration, drilling, cementing, completion, work over, sand control, stimulation, enhanced recovery and production. The role of industrial minerals in these operations is described. Some of the opportunities and problems affecting increased use of industrial minerals in drilling and stimulation are discussed.

Jan 1, 1983

By J. G. Groppo, B. K. Parekh

Removal of moisture from fine (minus 28 mesh) dean coal to 20 percent or lower level is difficult using the conventional vacuum dewatering technique. High pressure filtration technique provides an avenue for obtaining low moisture in fine clean coal. This paper describes a couple of novel approaches for dewatering of fine clean coal using pressure filtration which provides much lower moisture in fine clean coal than that obtained using conventional pressure filter. The approaches involve (a) split stream dewatering and (b) addition of paper pulp to the coal slurry. For Pittsburgh No. 8 coal slurry, split stream dewatering at 400 mesh provided filter cake containing 12.9 percent moisture compared to 24.9 percent obtained on the feed material. The addition of paper pulp to the slurry provided filter cake containing about 17 percent moisture.

Jan 1, 1995

By B. K. Mishra, R. K. Rajamani, P. Songfack

Primary grinding in SAG mills is gaining more importance with respect to the conventional crushing, rod and ball milling operations. This is due to the reduced operating costs generated by lower steel consumption. However. SAG milling is inherently susceptible to more severe risks and problems since it attempts to combine several stages of the conventional crushing and grinding into a single stage. This paper analyzes the SAG milling operation by predicting the motion of rocks and steel balls. The well-known discrete element method (DEM) is used to calculate the trajectories of individual entities, and their collision with one another. A computer code previously used for studying the motion of grinding media in ball mills is enhanced to handle the interaction between heavy spherical steel balls and light chunks of rocks, usually ellipsoidal in shape. The DEM based software called MILLSOFT can animate the charge motion for different design of liners. A case study of a 9.75-m diameter SAG mill is presented and the effects of lifter bar height and configuration on the overall dynamics of the charge are discussed. Also the effect of spacing between liners on lifting the charge is presented. This new approach has a large potential because it shows in detail the effect of each design or operating parameter on the performance of SAG mills.

Jan 1, 1998

By D. Park, V. Gall

The three-dimensional finite element technique combined with a progressive failure approach were used to simulate stress distributions in a complete mine section that occur in response to a longwall mining operation. Due to the availability of a Cray supercomputer, a large-scale, three-dimensional, finite-element model was developed for the analysis. The Hoek-Brown failure criterion, which describes a realistic behavior of rock masses, was used for the simulation of progressive failure. A comparison of calculated and monitored stresses in the mine has shown that the model gives a good representation of stresses in the mine structure.

Jan 1, 1992

By G. Bhaskar Raju, S. Prabhakar

The amenability of column flotation for the beneficiation of fluorspar was investigated, and the overall performance of the column, flotation was compared to the performance of the existing conventional flotation cells at the plant. It was estab¬lished that improved grades and recoveries could be obtained by adopting column technology. Acidspar concentrates as¬saying 97% CaF2, suitable for HF manufacturing, can be produced by adopting two-stage column cleaning in place of multistage cleaning by conventional cells. Similarly, metspar concentrates assaying 90% CaF2, suitable for metallurgical applications, can be achieved in a single-stage cleaning by column flotation. This is an improvement over what is now being achieved using the existing conventional rougher and three-stage cleaning cells in the plant. The number of stages, i.e.,four in the acidspar circuit and four in the metspar circuit, including rougher stages, can be eliminated by adopting a three-column configuration. Thus, the cost of production, the complexity of the circuit and the power consumption can be effectively reduced with other attendant benefits.

Jan 1, 2000

By R. H. Bartlett

Hydrometallurgical processes for copper flotation concentrates avoid the S02 emission problems associated with smelting, but they require oxidation of copper to obtain solubilization during leaching. The resulting copper ions must be reduced to metal, which normally requires large amounts of energy or energy equivalent reagents such as hydrogen or iron. The conventional reduction method is electrowinning which is labor intensive and involves 35 to 40% of both the en-tire operating and capital cost of the better hydrometallurgical processes. Smeltermen are correct in criticizing the available hydrometallurgical processes for being more energy intensive than modern smelting processes. Clearly, there is considerable incentive to reduce the cost and energy required for reducing copper ions from solution. Furthermore, it is thermodynamically possible to do this using sulfur contained in the concentrate itself. In fact, the thermodynamic potential of oxidizing sulfur from S+4 to the S+6 state is greater than required to reduce cupric ion to metallic copper. (1) Realization of this potential in a practical process would significantly reduce the cost of hydrometallurgical processing of sulfide concentrates because sulfur would become a cost-free reducing agent. An apparently practical method is to use SO3 and HSO3 ions, obtained by ammonia scrubbing of SO2 from a concentrate roaster gas, to reduce leached copper to metal in an autoclave. This reduction step is the Jumau 1907 patent. (2) A series of steps including sulfite reduction constituting a crude flowsheet was suggested by Parker in 1976(3), but apparently little development work has been done by him, since he has been interested in new routes of refining the resulting copper powder. The purposes of the present paper are to elaborate on the Jumau-Parker thrust. Describe a detailed complete sulfite process flowsheet based on materials and energy balances, discuss the chemistry, and discuss further work that is required to develop this process. The results of the present paper are largely based on a synthesis of the steps using handbook chemistry. Process materials, utilities costs, and energy requirements are projected to be unusually low.

Jan 1, 1978

By Donald P. Schlick

Gentlemen, today I would like to talk to you about metal and nonmetal mine health and safety--past, present and future. Briefly, I will comment on the past because it is important to an understanding of our present activity and our plans for the future. Federal inspection of noncoal mines was not authorized until 1966, when congress passed the federal metal and nonmetal mine health and safety act; public law 89-577, with the passage of this act, the federal inspector, for the first time, had the delegated authority and responsibility to enforce health and safety regulations designed to prevent personal injuries and occupational diseases, the new law also provided for the education and training of our miners; assistance to the operator through the transmission of technical and scientific information and assistance and equally important, the law made provision for state participation in the congressional mandate to prevent injuries and save lives in the mineral industry, Before I tell you about our program and our future plans, I want you to know that I am here to listen as well as to talk! In my view, the only kind of communication that is meaningful is two-way communication. Our nationwide progress in metal and nonmetal mine health and safety during 1972 cannot be measured in reduced fatalities or injuries. The unforeseen tragedy that took pace in Kellogg, Idaho, in may of last year mode that almost a certainty.

Jan 1, 1973

By Mark A. White

Surface mining of multiple seams by mountaintop removal and contour mining is complex in Appalachia. Arch of West Virginia, a division of Apogee Coal, has made its operations state-of-the-art to cope with this challenge. Arch of West Virginia moved into the heart of coal mining in Appalachia when Arch Mineral acquired coal reserves and coal operations in the southern West Virginia counties of Logan and Wyoming. These reserves were initially developed at the turn of the century as underground operations. Today, though, they are mined using mountaintop removal and contour mining. The steep slopes in the mountains of Appalachia generated a method of mining referred to as contour mining. During the late 1960s and early 1970s, contour mining was introduced at these operations using front-end loaders with bucket capacities of more than 7 m3 (10 cu yd) that could load 45-t (50-ton) end-dump trucks.

Jan 1, 1995