Search Documents

By C. H. Cheh

The amount of fines in run-of-mine coal has been increasing and coal quality has been deteriorating as a result of the increased use of mechanized and continuous mining methods. Removing the mineral matter and pyritic sulfur from coal prior to combustion will lower transportation costs, improve power plant performance and reduce sulfur dioxide emissions. Since physical cleaning methods can only remove individual particles of mineral matter and pyrite, it is necessary to crush and grind coal to fine sizes to separate these contaminants so they can be removed by deep cleaning processes. The increased portion of fines in run-of-mine coal together with attempts to increase the mineral matter removal efficiency have stimulated interest in fine coal cleaning technology. However, there are many problems to be solved before fine coal cleaning can be applied to power plant coals. These problems include: 1. coal cleaning plant capacity is reduced when conventional cleaning circuits are modifies to deep clean coals; 2. existing equipment and technology is not suitable for cleaning fine coal; 3. coal recovery is reduced; and 4. fine coal is difficult to dewater, dry, handle, transport and store.

Jan 1, 1982

By Dennis Z. Mraz, Maurice B. Dusseault

INTRODUCTION In 1982 and 1983, as part of the mine design program for a New Brunswick potash mine, series of laboratory tests were conducted on potash and salt samples obtained during the mine exploration program. Concurrently, two rock mechanics monitoring programs were initiated in-situ the short term test at site A, and the long term test at site B (figures 1 and 2). SHORT TERM TEST (FIGURE 1) The purpose of this test was to obtain a quick confirmation of laboratory data and comparison of the rock response to excavation with the data available from Saskatchewan potash mines. Instrumentation in the main drift was installed on Day 4 after excavation, and the pressure cells were pressurized on Day 33. The packer type cells in the east crosscut were pressurized on Day 25. Excavation of the west cross-cut was begun on Day 71. This "mine by" test has provided important information required for calibration of laboratory tests, as will be shown later. The test data recorded are shown in a series of diagrams: a. initial room closures, main drift-figure 3; b. convergence graphs, main drift-figure 4; c. stresses recorded, main drift-figures 5 to 8 and, d. stresses recorded, east crosscut - figure15 Three types of instruments were used in this test. In the main drift. Saskatchewan Research Council water type hydraulic inclusions. encapsulated in potash, were used to measure lateral and vertical stresses. In the east crosscut a home-made packer type hydraulic inclusion was used to record radial stresses. The convergence stations consisted of end-grouted bars of reinforcing steel. LONG TERM TEST (FIGURE 2) The purpose of the long term test was to study the steady-state behaviour of a single opening in potash. Site B was placed in a remote area of the mine, well away from any anticipated early mining activities. To assure homogeneity of rock mass, the site was placed within a 30 meter thick vertical limb of a syncline-shaped ore body contained within a 360 metre thick vertical section of salt rocks. It was excavated mechanically as close as possible to the designed square cross-section for the entire length of the room. The square cross- section was chosen in order to achieve a comparable geometry in vertical and horizontal directions; that is, to eliminate any undesired effects of geometry interaction with lithostratigraphy which might have generated non-homogeneous behaviour. The site was extensively instrumented. As in site A, the convergence stations consisted of end-grouted bars of reinforcing steel. However, in order to avoid any measurement inaccuracies which would be associated with the brittle yield zone in the opening walls, bars were placed to the same depth in opposite sides of the opening. This allowed the convergence measurement to be obtained as the absolute convergence between two points, rather than the convergence of a single point with respect to a potentially unstable reference. For stress measurements the Saskatchewan Research Council cells were placed vertically, laterally and radially. Unfortunately, due to cost considerations, it was decided to use a compacted sand, rather than grout, to encapsulate the cells in the boreholes. Due to the extremely small strain rates, only radial ly placed cells could be adequately pressurized. The rest of the cells did not perform adequately, and are currently being replaced.

Jan 1, 1986

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

By R. F. Korcak

There exists a wide array of industrial byproducts that produce beneficial responses in the soil/ plant environment. These materials range from clean-coal-technology residues produced during the generation of electric power (particularly those high in gypsum) to mineral fines produced by the aggregates industry (i.e., sand, gravel and crushed stone). A number of these materials are examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems are discussed.

Jan 1, 1997

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By D. Lauriski

The recent spate of catastrophic events at U.S. mines raises the question as to whether or not the mine safety and health system in the U.S. is broken. The prescriptive regulatory regime in the U.S. is not a cure-all for a broken system. Without totally dismissing the contribution of a prescriptive regulatory approach, this paper argues that safety in the U.S. mining industry would be enhanced if the nation adopted a scheme that provides a balance between specification standards and two alternatives: performance and systems-based standards. This would allow effective and flexible means to continuous health and safety performance improvement. Mine operators, regulators and politicians could then go beyond thinking that compliance alone equals strong safety by creating a proactive system that emphasizes continuous improvement. By adopting performance and systems-based standards, exemplary safety and health performers can be recognized, allowing regulators to focus their efforts on those without sound occupational safety systems and who have substandard safety performance. Mining Engineering, 2011, Vol. 63, No. 7, pp. 77-82. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Richard J. Leary

At the 1976 Annual Meeting of AIDE, Alan Merson reminded his audience that economic' success comes to those who understand things as they are, rather than as they have been or what ideology says they should be (1). He went on to say that, measured by this standard, the mining industry is in trouble. The mining firms had recognized long ago the importance of effective lobbying in Washington and the state capitals. But, he pointed out, those methods are nearly worthless anymore in coping with many land use problems because the critical decisions are likely to be made at the local level. There the tactics are far different as are the relations of the decisionmakers to the parties before then. Furthermore, in his estimation the trend is to leave land use regulation largely to the local level of government. All who are concerned for access to land for mineral development will be benefited by reading Professor Merson's paper lie is speaking effectively about the context of decisionmaking for specific cases, the shape of things in the here and now. There is, however, a longer-tern set of considerations that if pursued will be likely to foster the creation of public support for mining developments. At that sane meeting I spoke on two foundations of the long-term relationships: namely, the growth in requirements for minerals implied by projections of increasing consumption; and a rationale for fostering mineral exploration and development. I mentioned in passing the social decisionmaking process for public uses of land (2). This paper is intended as a complement. The growth of requirements for Minerals and the rationale for development based on the Entropy Law will be only mentioned. The main concern will be on the process of social decisionmaking in the context of access to land for mineral development.

Jan 1, 1976

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By S. Davis

It has been accepted almost as dogma that sampling contributes most of the error to fluctuations in gold fire assays. Differences in assay results on pulp material from the same sample interval are frequently regarded as evidence of the presence of the so called "nugget effect" or relatively coarse gold particles. It is true that if coarse gold particles are present they contribute to substantial sampling fluctuations, but while the process of sampling is probably the major source, the analytical process cannot -be completely ignored as a possible contributor to erratic assay results. In order to maintain a stable assay process, the analytic part of the system must be kept in control as well as the sampling and preparation part. One way of monitoring the performance of the analytic system is to systematically assay standard material whose sampling characteristics are carefully controlled. Gold assay standards are not prepared nor can they be prepared to account for both sampling and analytical errors. It is not possible to send coarse material to a lab for preparation (which includes both the processes of comminution and splitting) followed by fire assay, to make inferences only about the fire assay process. Because most gold ores are very heterogeneous, sampling errors would in most cases completely mask the contribution of the analytical errors. Assay standard material is prepared only to assess the accuracy and variability in the fire assay process.

Jan 1, 1995

By James J. Scott

To the safety engineer, mine planning engineer, and mine inspector associated with an underground operation, stability of the underground structure is of the utmost importance. In the United States in 1961 rock falls killed 167 miners, crippled many more, and cost the industry a fortune in lost equipment and production. Much research has been carried on to try to find ways to eliminate this loss of life and property. Within the past few years the interest in rock mechanics as a science has been at its highest point, Private industry, government agencies, universities and foundations have launched studies to gain a better basic understanding of the stability of underground openings.

Jan 1, 1966

By Gülhan Özbayoglu, Yusuf Ziya Akgök

The effect of cooling rate on the flotation behaviour of copper slags of flash smelter plant in Samsun was investigated. Fresh molten slag was solidified in laboratory scale in three different ways. All the samples were characterized by chemical and mineralogical analyses. The chemical analyses showed that samples prepared from fresh slag had 0.9 to 1 % Cu with 40 % Fe and 30 to 32 % SO2. Old pit slag samples contained between 1 to 3% copper. Microphotographs showed that rapidly cooled slags showed fine size distributions, e.g. the copper grains in granulated slag had sizes in 1-2 microns. On the other hand, the size of copper grains in slowly cooled slags increased above 40 microns. Flotation tests carried out by using potassium amyl xanthate and Flotanol-C showed that slowly cooled slag reduced the copper losses in the tailing and improved the grade of concentrate. Under the light of laboratory investigation, the pit dimensions of Samsun Plant have been modified which resulted in a pronounced improvement of the grade and recovery of concentrate produced at Samsun slag flotation circuit.

Jan 1, 1995

By P. B. Altringer

The Bureau of Mines, U.S. Department of the Interior, is investigating biodegradation of cyanide as a means of decommissioning heap leach operations. Biological oxidation decreased weak acid dissociable (WAD) cyanide in process solutions1from 50 to 170 ppm down to 0.1 ppm. The tests were conducted both in trickling column reactors, using quartz as the growth surface, and in upflow columns, using activated carbon as the growth surface. In addition, exploratory tests indicated that bacteria will destroy residual cyanide in leached ore. A flowsheet has been proposed for closure of heap leach operations in which the metals processing portion of the plant, possibly the carbon adsorption columns, or a collection pond is used as a bioreactor. The cyanide in the process solution is destroyed in the bioreactor and the treated water is used to rinse residual cyanide from the spent heaps. The water is recycled until the effluent WAD cyanide concentration meets discharge standards.

Jan 1, 1992

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By John Bailey

Stressmap is a program whereby the earth's stress field is charted in detail and utilized for design of mines and mine exploitation. This program is implemented by mapping the attitude (location, direction, dip, and extent) of induced rock ruptures during the process of hydrafracturing drill holes contiguous to mine interest. The program includes utilization of ancillary naturally occurring stress relief signals, They are precipitated because the earth is indeed dynamic and the strata of the crust are continually adjusting to load and/or strain differentials resulting in rock deformation and fracturing. These fracturing adjustments occur as small to tiny earthquakes comparable to Richter magnitudes of one, zero, minus one, and smaller events termed microearthquakes. Obviously, the earth's stress field changes due to continued differential loading and crustal movements; therefore it becomes conspicuously evident that resolving today's stress field as opposed to paleostresses is most important for efficient, economical, and safe mining operations.

Jan 1, 1974

By V 9. 0 / 300 dpi

Papua New Guinea (PNG) stretches from the equator to Latitude 12° South and from Indonesia's Irian Jaya Province in the west to the Solomon Islands in the east (Figure 1). The population totals 3.5 million people who are mostly concentrated in highland valleys on the main island and around the coast. This paper outlines the history of mining, describes the natural, cultural and regulatory setting of mineral discoveries and highlights, by example, some of the more idiosyncratic environ-mental aspects of mining developments in PNG. It concludes with remarks on the progress made in the fifteen years since environmental matters entered the agenda for the establishment of a new mine in PNG.

Jan 1, 1988

By Harry Perry

Although the markets for coal in the United States have changed rapidly over the last three decades, the uses of coal, namely, to produce heat and power or coke have been left almost unchanged. The coke is used either as a chemical reducing agent alone or as a reducing agent and source of heat. Most of the heat and power markets for coal require no coal processing, although for more than 50 years, many proposals to skim the more valuable substances in coal before burning have been advanced. Thus, the only large tonnage market requiring processing of coal is high-temperature carbonization to make coke. At present, coal requires processing for some small markets, but for future potential large markets, such as gasification, conversion to liquid and gaseous fuels, and conversion to chemicals, coals will require more processing than is now being done.

Jan 1, 1962

By B. C. Paul, R. Q. Honaker, M. Huang

Froth flotation is now, the most commonly used method for cleaning fine-coal fractions in coal-preparation plants. Past research and industrial practice have demonstrated that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, the efficiency of froth flotation decreases sharply as the concentration of middling particles increases. This is due to the flotation of high-ash particles that have a small amount of hydrophobic coal present at the surface. Because gravity-based processes are much more efficient for the treatment of middlings, the application of centrifugal washing for fine-coal cleaning was studied with an emphasis on the primary cleaning of fine-circuit feed. Results are shown of a parametric study that used a semibatch Falcon centrifugal concentrator. The results of the study revealed that separation performance is a function of particle size, bowl geometry, feed solids content and feed rate.

Jan 1, 1996

By J. K. Shurie

Calcined high quality bauxite is a staple raw material of the abrasive industry world-wide. The author discusses the factors which affect the economic value of calcined abrasive grade bauxite, and proposes an approach to the problem of estimating the relative value of available materials.

Jan 1, 1990