Search Documents

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003

By Salam Moubarak, Thomas Camus

"INTRODUCTION Since the introduction, several decades ago, of the first concepts of tunnel boring machines (TBMs), the unremitting increase of mechanized and automated tasks and the reduction of manual tasks carried out by human operators have gone hand in hand with the continuous improvement of these machines. In the present state of TBMs, the replacement of worn cutting tools is a critical, tedious, and dangerous manual operation especially for earth pressure balanced (EPB) and slurry TBMs. For such pressurized TBMs, hyperbaric interventions are used. They consist in replacing the pressurized soil/mud inside the chamber with compressed air that balances the face pressure. The operators can then ""dive"" into the chamber; however, because the human body cannot naturally undergo pressure changes, they have to follow strict procedures that have been developed for subsea divers, based on decompression stops. Indeed such interventions are actually quite often performed by professional deep-sea divers. The pressurized TBMS are consequently equipped with a manlock that allows for the required compression and decompression cycles. Hyperbaric interventions increase risk to the operators and require long decompression procedures that increase the TBM idle time and reduce its efficiency. At higher pressures, over 3.5 bar (ITA Report No 10, 2011), specific equipment and special gas mixes and/or saturation techniques are recommended (Lamont, 2012). Such procedures are even more expensive and time consuming although the duration of work in the pressurized area can be very limited for health and safety reasons. Contractors are therefore increasingly interested in automating these operations to reduce the risks to human workers and improve the TBMs performance. Moreover, the demand for new, ambitious and challenging tunneling projects (very deep, high pressure boring) is ever increasing, but the supply of suitable TBMs is limited and the risk from working in the hyperbaric environments becomes increasingly unacceptable. Impact of hyperbaric interventions The UK Health & Safety Executive has analyzed the consequences of working in intermediate pressure compressed air. The retrospective study of decompression illness (DCI) indicated that at certain pressures its incidence was around 2% of all exposures. More worryingly it showed that over 20% of the exposures commonly undertaken by shift workers in tunneling (those over 1 bar pressure for 4 hours or more) resulted in DCI. It was concluded that on some contracts up to 50% of shift production workers experienced DCI at some time during the contract, a situation which was considered to be wholly unacceptable (Lamont, 2006)."

Jan 1, 2016

By Edward K. E. ] [Williams

Conditioning is any treatment of an ore with or without reagents which affect its floatability. While it can start in crushing or grinding circuits and continue into the flotation circuit, conditioning will refer here only to reagent treatment in an agitated tank designed for the purpose. Such treatment is often unnecessary with sulphide ores and collectors or with amines,* but it has long been recognized as essential with fatty acid collectors in the flotation of non-sulphide minerals, The requirements can be extremely variable, depending upon ore alteration, the presence or absence of slimes, and 1 the minerals to be separated. The study described here was concerned with the recovery of oxidized molybdenum minerals from an ore containing the element in both sulphide and oxidized form. Flotation of the iron minerals with which the oxidized molybdenum was associated was the basis for the process. Recovery and optimum concentrate grade without desliming depended upon a twenty to thirty minute conditioning of the pulp with flotation reagents at forty to fifty percent solids and at high turbulence. The objective in the study was the determination of design and operating criteria for conditioners in order to permit scaling-up of the results without repeating the entire study on a larger scale.

Jan 1, 1968

By Peter M. Fozzard

A review is made of the actual costs of recent foreign mineral exploration programmes in third world countries. Target identification leading to the selection of areas, or macro-targets, must follow a well planned and defined series of steps. Suggestions are made with respect to this inter-active project development work. Potential revenues in the broad sense will always determine the overall economics of exploration but clear objective philosophy, good planning and adequate financing are essential for exploration success. Considerable opportunities exist for making important foreign mineral discoveries and broad selected suggestions are made for the identification of exploration areas in relation to high-grade and precious metal mineralization.

Jan 1, 1984

By John B. Squyres

The purpose of this paper is to describe certain features of the uranium deposits of the South San Juan Basin, and to suggest a mode of origin for the deposits which is consistent with the data. A series of photographs is included at the end of the paper to illustrate the nature of the ore bodies. Since the general geology of the Grants Region is well described in the literature, it will be only briefly reviewed, and the time will be spent instead on the morphology, spatial relations, and geochemistry of the ore deposits. Part of this material is original, but data and ideas have been taken from a variety of sources, including the literature and the personnel of the USGS, the AEC, and many of the operating companies of the South San Juan Basin. I gratefully acknowledge these sources. The accuracy of the data and the conclusions presented here are my own responsibility, however.

Jan 1, 1974

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their coal. Sulfur was the major concern, with BTU and sodium limiting the market for some. The Clean Air Act has extended the PRB market into plants converting from other coals. These new customers are more sensitive to constituents affecting boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to control cost more stringently than ever. Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998

By J. Boisvert, E. Daniels, C. Deutsch

"INTRODUCTION Conventional mine planning is performed on a single resource model at a selective mining unit (SMU) scale deemed appropriate for the deposit and mining method. Estimation methods such as kriging and inverse distance, commonly used to construct a single model, are susceptible to histogram smoothing (Rossi & Deutsch, 2014). This can be mitigated by limiting the number of composites per estimate, therefore correctly reproducing the distribution of estimates (Boisvert & Deutsch, 2012). Search limiting techniques remedy histogram smoothing at the cost of introducing a problematic conditional bias (Isaaks, 1999) and introduces even greater spatial smoothing. Localization is an alternative, offering histogram reproduction through post processing of more robust probabilistic modeling techniques. A single localized model at the SMU scale is desirable. The correct histogram can be reproduced and a single model allows for the use of conventional mine planning and resource evaluation techniques. Despite the advertized benefits of localization, the necessary reliance on a larger panel scale as a middle step in the localization process yields unsightly “edge-effect” artifacts (Boisvert & Deutsch, 2012). Two approaches to artifact reduction are presented here. The first is a straight forward optimization approach designed to minimize an objective function that penalizes artifacts including panel edge discontinuities to generate a model free of panel edge-effects. The second approach redefines a panel in a less conventional fashion as a randomly chosen set of SMUs throughout the domain. This method produces a model void of any regular panel shape resulting in an artifact free model. Artifact reduction minimizes the obvious “edge-effect” issues of localization but local precision issues described by Boisvert & Deutsch (2012) persist. Localization is not a replacement for quantified uncertainty for comprehensive risk analysis and resource evaluation. LOCALIZATION Initially developed with Uniform Conditioning in mind, localization collapses a distribution of local uncertainty at a panel scale to an SMU scale model for mine planning (Abzalov, 2006). This process has been extended to Indicator Kriging (Hardke, 2011), Sequential Gaussian Simulation (Boisvert & Deutsch, 2012) and MultiGaussian Kriging (Daniels and Deutsch, 2014). The localization process is performed in a similar fashion regardless of which technique is chosen to create the prior model of uncertainty. Methodology There are three scales of importance considered in the localization process. The point scale, otherwise known as the data scale, is the smallest and is the scale at which experimental data is collected. The SMU or block scale is the familiar scale at which mine planning and resource evaluation takes place. Lastly, the panel scale is larger and contains a number of SMUs. Each of the three scales is illustrated in Figure 1."

Jan 1, 2015

By William C. Baldwin

Unitization and containerization continue to grow with great rapidity throughout the world today. Every industrial nation outside of the Iron Curtain is devoting more and more time toward research of these developing sciences. Unitization and containerization are proving to be the solution to many of modern industry's most pressing handling and shipping problems. Manufacturers make large savings, carriers receive many benefits, and customers take an increasing interest in demanding that their shipments either be unitized or containerized. Unit-loads consist of items, packages or bulk materials pre-assembled into a convenient mass for handling by mechanized equipment and to fit the internal dimensions of carriers. It has been found that unitized handling and shipping offers cost savings too great to be ignored by anyone interested in the distribution of goods. At present, the benefits from unitized shipping and handling are being enjoyed only to a small extent due to the failure of many persons concerned with handling practices in recognizing only some of the advantages of unitization. Before the full benefits of unitized handling and shipping can be realized, some major changes in packaging and distribution practices will be necessary on the part of industry. Numerous investigations in the last two years show conclusively that there are more advantages and more inherent savings for shipping goods on pallets in unit loads than by any other method. There is no question that unit-load handling can offer significant advantages to the user over piece-by-piece package handling. Reduction in handling costs is the primary objective of such activities, but it is by far not the sole objective. Some of the other benefits that can be realized are:

Jan 1, 1973

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985

By Lj. Obradovic

The aim of this paper is to study the feasibility of copper and gold recovery from the old flotation tailing dam at Bor, Serbia. Laboratory leaching experiments were carried out using a composite sample taken by drilling from 16 - 40 m depth. Different oxidation agents as FeCl3, Fe2(SO4)3 and H2O2 were used. An H2SO4 solution with a pH less than 3 was used for leaching. The influence of a number of parameters on the recovery of both elements as temperature, pH, duration of leaching and concentration of oxidation agents was also studied.

Jan 1, 2006

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By Karl A. Olsson

The Glenharold Mine is a surface mine operated by Consolidation Coal Company. The mine is located approximately 90 kilometers (55 miles) northwest of Bismarck, and 3 kilometers (2 miles) southeast of Stanton in west central North Dakota. Glenharold has a nominal design capacity of 3.0 million metric tons per year (3.3 million short tons per year). With the exception of local coal sales, this production supplies fuel for Basin Electric's Leland Olds generating station, a mine mouth power plant. The mine has 175 hourly and 50 salary employees. The Glenharold reserve extends over 210 square kilometers (80 square miles). The mining area is on a dissected plateau between the broad flat Missouri River flood plain to the north and the gently rolling uplands to the south. Erosion by intermittently flowing streams has produced many narrow, steep-walled, drainage ways. Mining begins at the 6 meter (20 foot) cover line and continues to the economic recovery line.

Jan 1, 1982

By C. F. Curry

In the early 1940's Humphreys Mining Company in Florida pioneered heavy mineral mining with a dredge in the United States, In 1948 Du Pont, in conjunction with Humphreys, opened their first of two mining operations recovering a titanium dioxide product in Florida. Later on in 1952 Du Pont opened their second plant, both of which used a cutterhead suction type of operation. This process is also used in heavy mineral mining in Australia and Africa. In 1957 ASARCO started prospecting in New Jersey. Test borings indicated a large deposit of ilmenite bearing heavy mineral sands had been deposited and concentrated in an area near Lakehurst in central New Jersey. Humphreys Mining Company was contacted about the possibility of mining the ASARCO New Jersey property in much the same way as Du Pont and themselves were doing in Florida. An extensive study was made to determine the economic feasibility of mining the ASARCO property. During this study, extensive test drilling and samples for a pilot plant were taken.

Jan 1, 1975

By Z. Kowalski

In the defunct Gorka quarry, there are situated both a waste disposal site of an area of 6.7 ha and containing approximately 1 million ton of high aluminium wastes and a pond of an area of roughly 3 ha, up to 15 m deep, with about 400000 m3 of polluted water. The reservoir is fed with the filtrates arriving from the disposal site mentioned, at a rate ~130 m3/day. An alarming phenomenon is the subsidence of the pond bottom and the infiltration of solutions into the Triassic and Jurassic water resources, assessed at ~40 m3/ day. The basic problem related to the effluents in the Gorka pond is their high alkalinity (pH 12-13.4) and variable pollutants whose level increases appreciably with the pond?s depth. The solution offered provides pumping out and treatment of about 500000m3 of effluents retained in the Gorka reservoir in an about yearly time. Effluents would be treated in a reverse osmosis plant, according to a process so far verified on a quarter-commercial scale. The treatment process by-product would be discharged into the Ropa stream. The brine solution (containing about 25% NaCl), whose amount may reach up to100000m3, might be supplied to the Debiensko Mine which produces technological salt from salt-bearing mine waters. Similarly, there would be provided an intake of underflows of infiltrates (by means of deep wells, and possibly girdling ditches) arriving from the high aluminum site, and such effluents would be subject to ongoing dilution in water courses. It would be possible to test the system of underflows reaching the Gorka reservoir by means of geochemical identification, previously performed. The next stage following the pumping, would be the utilization of approx. 50 000m3 of bottom slurry. Highly alkaline slurries would be utilized in the production of self-solidifying mixtures. Slurries would be pumped out and temporarily dumped on drying beds, located nearby the Gorka reservoir, and later on used successively for making self-solidifying mixtures in a plant similar to a concrete making seat. Those mixtures would be applied for sealing the bottom of the Gorka reservoir and the necessary part of the edges of the defunct quarry. An alternative solution is the utilization of slurries in the facilities of the Trzebionka Mining Works and the application of self-solidifying mixtures, made in the Trzebionka Works, for sealing the reservoir bottom.

Jan 1, 2006

By I. Orisek

The methodology and results of a feasibility study of an Automatic Truck Dispatching (ATD) system in an actual open pit mining operation, are presented. Using mine cost data, an economic analysis confirms that capital and operating cost savings with ATD out-weigh the costs. Productivity improvement achievable with ATD is quantified with a computer simulation of truck haulage based on mine production and operational data.

Jan 1, 1986

By J. W. Lowry

After years of processing copper porphry ores, the Ray concentrator of Kennecott Minerals Company installed a concentrate regrind mill in its flotation circuit. The first cleaner concentrate is reground rather than the usual rougher concentrate. An additional cleaning of the reground product yields an increase in copper content of the final concentrate and a significantly lower insol content. The desired goal of decreasing the energy requirements for smelting the concentrate has been achieved.

Jan 1, 1980

The most common method used for cleaning the fine fraction in today's coal preparation plants is froth flotation. Past research and practice has found that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, its efficiency decreases sharply as the concentration of middling particles increases due to the flotation of high-ash particles having a small amount of hydrophobic coal present at the coal surface. Since gravity-based processes are much more efficient at treating middlings, the application of centrifugal washing for fine coal cleaning has been studied with an emphasis on the primary cleaning of fine circuit feed. Results will be shown from a parametric study using a Falcon centrifugal concentrator which reveals that the separation performance is a function of particle size, bowl geometry, feed solids content, and feed rate.

Jan 1, 1994

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

By John W. King

reserves are exploring to increase them.. Uranium exploration projects are known to be active or planned also in Guayana, Colombia, Ecuador, Peru, Chile, Bolivia, and Uruguay in South America; in the UAR, Nigeria, Angola, Mozambique, Malawi, Kenya, and Somali in Africa; and in Greece, Iran, Pakistan., Indonesia, and New Zealand. The above list, to which several might be added makes a total of at least 43 nations actively interested in exploration for nuclear raw materials. As we consider the distribution of the world's uranium resources, it is interesting to note that roughly one third of the total occurs in deposits that are economically dependant upon another product. The very large reserves of South Africa could not be produced for uranium alone, but gold has carried a sufficient part of the total cost that uranium can be recovered profitably. Approximately 40 percent of the US reserves, or 120,000 tons, are estimated as by-product recovery from porphyry copper and phosphate operations, but these reserves are not presently in production. The remaining two thirds of the world's uranium reserves have been sought, developed, and produced primarily for their uranium content. Those deposits are estimated to contain 613,000 tons of uranium oxide recoverable at less than $10 per pound. Nearly half of that uranium occurs in unmetamorphosed sandstone hosts, mostly of late Phanerozoic age--the Colorado Plateau type. About 30 percent is contained in the quartz pebble conglomerates of southern Ontario, Canada, and 20 percent is in magmatic-related deposits--veins, contact deposits, mineralized breccias, etc.

Jan 1, 1969

By K. A. Grace

"An ore is a rock regardless of its rarity or value."* The application of geology does not cease with the discovery and delineation of a mineral resource, but continues in the calculation of the economic parameters that determine reserves. Reserve determination, reduced to essentials, is the determination of the cost of production of a mineral commodity from a resource. This cost comprises mining, processing, waste disposal, reclamation and marketing costs. Geological input is vital in the calculation of the individual cost parameters from mining to reclamation, and even has some impact on marketing. Geology thus has a critical role in the determination of reserves.

Jan 1, 1985